Here is my 2000 limited 4runner w/ elocker. I had a 97 Tacoma about 5 years ago that I modded the crap out of over at Tacomaworld which led me to buying this 4runner.Tacoma build

IG: 415yota

How it sits today(185k):




When I bought it (178k):


Exterior/Armor:
-Addicted off-road front bumper
-Eimkeith rear bumper w/ f150 tank kit
-9.5k smittybilt synthetic winch & factor 55
-4xinnovations front skid set
-RCI transfercase skid
-BAMF sliders
-Lotus rear LCA skids
-Satoshi grill w/ toyota emblem
-SRQ turn signals (paint matched+relay)
-Blacked out rear emblems
-Ruffstuff rear diff guard
-eBay snorkel w/ TRD badge
-hood w/ scoop
-Arb awning w/ light kit 6’
-DIY roof rack
-HF spindle gussets
-eimkeith LCA kit
-eimkeith coil bucket kit

Drivetrain/Engine
-Marlin crawler tacobox w/ 2.28 gears
-5.29 gears from ECGS w/ front arb locker
-ECGS front diff bushing
-ARB diff breather kit (front diff, transfercase/transmission, rear diff)
-B&M transmission cooler
-Borla muffler w/ turndown
-AFE stage 2 intake (modified to fit with the stock intake box)
-Tomwoods F/R driveshafts
-trans-go kit (truck setting)
-Front diff drop kit

Suspension/Tires:
-Toytec bilstien coilover kit front/rear
-JBA UCA’s
-Durobumps front/rear (stock length)
-Bora 1” spacers x4
-ES steering rack bushings
-ES body mount bushings
-Toytec 1” body lift
-eimkeith PCK
-Steering column weld/tilt ball spacer
-Method 312 rims w/ 315/70/17 cooper stt pro’s
-Wheelers extended SS brake lines
-13wl tundra brakes
-Opt Offroad rear control arms

Maintenance/Replacement Parts:
-New OEM LBJs + OTRs
-New Napa cv’s (I plan on rebuilding my oem ones)
-New dash ‘crash pad’
-New center armrest
-New tundra pads + rotors
-Valve cover gasket/plugs/wires/pcv
-New moon roof
-New rear hatch (spoiler delete)
-New oil/filter/coolant/gear oil/power steering
-New o2 sensors (both)
-DIY Alignment
-Steering rack guide
-Replaced alternator brushes
-Rebuilt starter x2
-Rear hatch strut bushings
-New fuel filter
-New gas cap
-Replaced all bulbs in dash
-Removed old security system
-Rebuilt climate control
-Timing belt/radiator/coolant inlet+outlet
-New shifter bushings
-cleaned/rebuilt injectors
-whiteline LCA bushings
-new toyota TPS
-cleaned IAC
-new door lock motors
-door stopper repair
-rear main seal
-misc transmission/tcase seals
-transmission solenoids
-Fan clutch
-muffler gasket

Lighting/Electrical:
-bxbuilt turbine led projectors w/ rear switchback halos
-Rigid 20” single row led bar
-CBI hood mounts w/ rigid d-pods
-Firestick cb antenna w/fire ring cable
-Rigid orange flush mount fog lights
-Rigid ignite reverse lights
-Rigid rock light kit
-OTTRAW switches
-Military battery terminals
-Led interior bulbs throughout
-Kenwood Navi head unit w/ switch for antenna
-alpine type S speakers w/speaker mounts
-Grey wire mod
-scangauge
-ram phone mount

Miscellaneous:
-New leather for seats & steering wheel
-arb compressor w/ quick connect for filling tires
-Weather tech mats (front, rear, cargo)
-DIY hood struts
-Scarab windshield washer kit
-tubbed for 37” tires

Waiting to be installed:
-Front/reverse camera
-drawer/bed/fridge system
-new throttle cable
-cv rebuild kit
-new cv axle seals

nice color combo. looks good.

Thanks!

A belated welcome to the forum. Your years of Tacoma experience should serve you very well with your new purchase. Congratulations! Looks very nice.

Was up late researching sliders actually, and BAMF is on my short list. Cool that they are local to us here...

Thank you! Jerry does some top notch work, wish he had more stuff to offer for our T4Rs.

I've seen photos only, but his sliders look very nice indeed. I imagine you plan to pick them up locally... His are longer than most and will entail that us Limited guys trim fender flares - i believe. I look forward to your install.

Nice rig! Looks really clean and ready to go for the plans you have for it. Sounds like you have done a lot already!

I had his sliders on my Tacoma as well as his shock relocation kit. Yea I’m going to pick them up. I think your right about trimming the flares a bit, hopefully it’s not too much.. I’ll post up pics


Thank you! Yea I’m trying, it’s had a few owners so there is a lot of little stuff to go through.

Changed all the gear oil to redline today. Finally finished installing the LBJs, UBJs, OTRs, CV’s, wheel spacers, and steering rack bushings today as well..
Tomorrow I’m going to finish installing my radio and take it to get smogged.

Welp just got the smog done, thought I was going to have to come back because I had the battery disconnected. Got a couple pics real quick while driving it around. When installing the radio I installed a switch for my antenna (I never use the radio..)

Runner looks good! You should bring your "new to you" 4runner to Tim and I's semi-annual BBQ/MOD day at his place...

It will be November 3rd.

https://www.youtube.com/watch?v=4e5yMEUkVzY

Thank you! I was actually one of the first people to sign up, definitely will be there.

Drove it up to Tahoe over the weekend for my wedding, seemed to do good although when it was really cold the rear struts for the tailgate were pretty much useless.. smashed my finger so hard that it popped today, ouch.. more updates coming soon..

Strongarm struts. I recommend the overcharged model if you have any extra weight on the liftgate, I added a few pounds of sound deadening so it helps.

Nice buy! I'm not always the biggest fan of the two-tone colors, but I really like the green/grey combo.