11-05-2020, 07:47 PM
|
#1
|
Member
|
|
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
|
Member
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
Random extra bolt on engine block
Reassembed my engine after a HG/Timing job. This random bolt on the passenger side just above the exhaust manifold is left. When I removed stuff I typically install bolts back in the holes. But...everything's connected and running fine so I don't know what this is.
this is on the 5VZFE
|
|
Reply With Quote
|
11-05-2020, 08:29 PM
|
#2
|
|
Member
|
|
Join Date: May 2020
Location: Ontario
Posts: 424
|
|
Member
Join Date: May 2020
Location: Ontario
Posts: 424
|
Nothing goes there,.. So I'd say maybe from the ATF upper dip tube support to engine?, looks about right length and size, plus you might not notice it in its actual location if I'm right, and would make installing that head difficult.
__________________
99' Ltd E-locker grey wired, 4R Bilstein 5100, 99 tall coils, 906 OME & 1.5" spacers, 2015 4R Trail Edition 275/70R17, 1" RB BL
97' SR5 E-locker grey wired, Warn winch, 2" RB BL, Sonoran Steel 1.2 lift, dual battery, 1000W inverter, Hydraulic Arctic plow, 12" x 33" Baja Claw
92' Eclipse GSX AWD 6/4 bolt combo, 28 PSI boost, Meth injection, 750cc injectors, FMIC, 2.5" IC piping, full 3" exhaust, 350AWHP, lowered, Alum flywheel, 6 puck Clutch, Cams, JDM gear set,VC rear diff, EPROM ECU
Last edited by Malcolm99; 11-05-2020 at 08:32 PM.
|
|
Reply With Quote
|
11-05-2020, 08:42 PM
|
#3
|
Member
|
|
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
|
Member
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
the ATF dip tube is about 4 inches left of that bolt and it's hooked up already. All my ground straps are hooked up and everything. what the heck?
|
|
Reply With Quote
|
11-05-2020, 09:31 PM
|
#4
|
|
Member
|
|
Join Date: May 2020
Location: Ontario
Posts: 424
|
|
Member
Join Date: May 2020
Location: Ontario
Posts: 424
|
Ya that's why I was thinking dip tube bolt, as that new Head wouldn't go on with the bolt left in place and the dip tube hanging there, dunno man, nothing goes in that location in the USDM 5vz-Fe. Only other hardware like that would be PS ALT AC stay bolts and the intake to mounting brackets, and fender to mounting brackets, keep looking, unless you have extra hardware you stole from inventory..
__________________
99' Ltd E-locker grey wired, 4R Bilstein 5100, 99 tall coils, 906 OME & 1.5" spacers, 2015 4R Trail Edition 275/70R17, 1" RB BL
97' SR5 E-locker grey wired, Warn winch, 2" RB BL, Sonoran Steel 1.2 lift, dual battery, 1000W inverter, Hydraulic Arctic plow, 12" x 33" Baja Claw
92' Eclipse GSX AWD 6/4 bolt combo, 28 PSI boost, Meth injection, 750cc injectors, FMIC, 2.5" IC piping, full 3" exhaust, 350AWHP, lowered, Alum flywheel, 6 puck Clutch, Cams, JDM gear set,VC rear diff, EPROM ECU
Last edited by Malcolm99; 11-05-2020 at 09:33 PM.
|
|
Reply With Quote
|
11-05-2020, 10:57 PM
|
#5
|
|
Elite Member
|
|
Join Date: Oct 2014
Location: Citrus Heights, California
Age: 36
Posts: 7,337
Real Name: Jerod
|
|
Elite Member
Join Date: Oct 2014
Location: Citrus Heights, California
Age: 36
Posts: 7,337
Real Name: Jerod
|
Nothing goes there. The cylinder heads are identical did you switch them around? On the other side there's a bunch of items that bolt on that side such as the alternator drip shield.
|
|
Reply With Quote
|
11-05-2020, 11:20 PM
|
#6
|
Member
|
|
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
|
Member
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
No the shop had them kept together with camshafts and everything so they couldn't be swapped. I have no brackets left either nor other screws. I'll re-vist my steps and the breakdown and see how the part count goes.
|
|
Reply With Quote
|
11-07-2020, 05:58 PM
|
#7
|
Member
|
|
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
|
Member
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
OK I took more pics. I also rewound my steps and couldn't find where it came from. It's 12mm and it doesn't have the self tapping starter like the frame bolts. I had everything in baggies labeled from where they came. This must have been on the passenger side head baggie with the camshaft bolt, ground bolt and nut from the rear of the head, etc. So i threaded it in when I put the head back thinking i would come back to it. And in the instance of me mislabeling it in the wrong baggie, there's no bracket missing from the driver side either. I marked with yellow and red circles where grounds straps, intake stay bolts, fuel line bolts, etc go and they're all there.
|
|
Reply With Quote
|
11-07-2020, 11:36 PM
|
#8
|
Elite Member
|
|
Join Date: Aug 2013
Location: Stouchsburg PA
Posts: 5,323
|
|
Elite Member
Join Date: Aug 2013
Location: Stouchsburg PA
Posts: 5,323
|
Do you have anything left over. Like a little tab with a square hole to anchor a wiring harness?
Sent from my iPhone using Tapatalk
|
|
Reply With Quote
|
11-08-2020, 03:41 AM
|
#9
|
Member
|
|
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
|
Member
Join Date: Dec 2015
Location: Seattle, WA
Posts: 570
|
Not that I am noticing. The main "attachments" that I recall are the tranny dipstick and ground strap on the back of the head on the passenger side, then the ground strap, diagnostic plug, manifold stay, and fuel line on the driver side.
|
|
Reply With Quote
|
11-08-2020, 07:41 AM
|
#10
|
Member
|
|
Join Date: Mar 2006
Location: Huntsville, Al
Posts: 687
|
|
Member
Join Date: Mar 2006
Location: Huntsville, Al
Posts: 687
|
If the heads are identical and the other side has some attachments then it would make sense that this side has the same bolts with nothing attached. Also it might be worth a quick trip to a junkyard to look at a similar engine
|
|
Reply With Quote
|
11-08-2020, 12:19 PM
|
#11
|
Elite Member
|
|
Join Date: Aug 2013
Location: Stouchsburg PA
Posts: 5,323
|
|
Elite Member
Join Date: Aug 2013
Location: Stouchsburg PA
Posts: 5,323
|
On the passenger side it’s an empty hole on my engine.
Sent from my iPhone using Tapatalk
|
|
Reply With Quote
|
11-08-2020, 12:55 PM
|
#12
|
Member
|
|
Join Date: Jun 2014
Location: Port Hueneme
Posts: 64
Real Name: Mike
|
|
Member
Join Date: Jun 2014
Location: Port Hueneme
Posts: 64
Real Name: Mike
|
That Hole on my 97 is empty.
Mike
|
|
Reply With Quote
|
11-08-2020, 02:01 PM
|
#13
|
|
Senior Member
|
|
Join Date: Jun 2016
Location: MS
Posts: 2,508
Real Name: Mark
|
|
Senior Member
Join Date: Jun 2016
Location: MS
Posts: 2,508
Real Name: Mark
|
Bag n tag with ? On bag you may or not need it later, I have bag labeled that stuck to toolbox with magnet couple in it. It happens.
|
|
Reply With Quote
|
11-08-2020, 09:34 PM
|
#14
|
Junior Member
|
|
Join Date: Apr 2019
Location: Santa Rosa
Posts: 9
|
|
Junior Member
Join Date: Apr 2019
Location: Santa Rosa
Posts: 9
|
I had a U-Shaped metal shim left over once from doing a HG repair on a 95 Sonoma. Had no clue where it went, put it on the bench and went for a test drive, would up being a connecter piece for fuel lines
|
|
Reply With Quote
|
11-08-2020, 10:19 PM
|
#15
|
Member
|
|
Join Date: Sep 2020
Location: Ohio
Posts: 507
|
|
Member
Join Date: Sep 2020
Location: Ohio
Posts: 507
|
I think I remember taking those bolts off during a valve cover job.
______________
2000 Toyota 4Runner 4x4 Limited Sport Edition V6
|
|
Reply With Quote
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
|