User Tag List

Reply
 
Thread Tools Rate Thread Display Modes
Old 12-02-2020, 09:45 PM #1
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
Loosening 'New Style' Steering Rack Guide Lock Ring

Hey All,

I have an '01 T4R with the "updated" steering rack guide (i.e. 24mm hex to remove) that I would like to tighten up a bit to see if it improves slight steering play. I have already tack welded the shaft and this seems like another area to gain a little bit more response and reduce the amount that the truck gets pushed around by wind.

My problem is that I am unable to loosen the lock nut/ring that puts the guide cap under tension. I have soaked it pretty good with penetrating oil but its been no match for 20yrs and 230k miles of New England driving. It is corroded but not horribly so, but I suspect it has never been removed.

Has anyone else had this problem? What's the safest way to remove it? Is a torch safe on the rack housing with the fluid and seals inside? Can the nut be cut in such a way to allow for a nailset/screwdriver removal? Keep soaking with WD40 and give up if it doesn't move?

I would love to tighten up the guide a few degrees but its not worth hurting anything expensive on a silly lock ring.

Thanks!
tgreenwood75 is offline   Reply With QuoteReply With Quote
Old 12-02-2020, 11:18 PM #2
Dom8706's Avatar
Dom8706 Dom8706 is offline
Member
 
Join Date: Dec 2019
Location: Portland, OR
Posts: 216
Dom8706 is on a distinguished road
Dom8706 Dom8706 is offline
Member
Dom8706's Avatar
 
Join Date: Dec 2019
Location: Portland, OR
Posts: 216
Dom8706 is on a distinguished road
Quote:
Originally Posted by tgreenwood75 View Post
Hey All,

I have an '01 T4R with the "updated" steering rack guide (i.e. 24mm hex to remove) that I would like to tighten up a bit to see if it improves slight steering play. I have already tack welded the shaft and this seems like another area to gain a little bit more response and reduce the amount that the truck gets pushed around by wind.

My problem is that I am unable to loosen the lock nut/ring that puts the guide cap under tension. I have soaked it pretty good with penetrating oil but its been no match for 20yrs and 230k miles of New England driving. It is corroded but not horribly so, but I suspect it has never been removed.

Has anyone else had this problem? What's the safest way to remove it? Is a torch safe on the rack housing with the fluid and seals inside? Can the nut be cut in such a way to allow for a nailset/screwdriver removal? Keep soaking with WD40 and give up if it doesn't move?

I would love to tighten up the guide a few degrees but its not worth hurting anything expensive on a silly lock ring.

Thanks!
Just out of curiosity how much torque do you think you are using trying to remove it? Are you using a hex socket on a breaker bar or a hex allen wrench?

I know those guides are only suppose to be torqued to 18 FT LB so it shouldnt need much but like you said after years of not moving it could be rusted up pretty well. Either way if it was me id use a cheater bar to get as much length as possible for better leverage. 24mm is a big hex so i dont foresee any stripping or issues from giving it a good amount of torque. Id personally stay away from using heat in that area but other people might say different.

Im actually going to be doing the exact same thing this weekend for the same reason. Let me know how big of a difference it made if you can. Im trying to track down my freeway wondering.
__________________
02 T4R SR5 3.4L AT 215k - TJM Front Bumper - Coastal Offroad Rear Bumper - 914Z Ditch Lights w/ CBI brackets - Ebay Snorkel - Airaid MIT - Big 4 - B&M 70268 - Complete Suspension Rebuild - OME 881/906 Coils - OME 90004/60028 Shocks - ToyTec 1" BL - SS Diff Drop/Panhard Bar/Rear Body Mounts/Hi Lift Mount. Plus other stuff.
Dom8706 is offline   Reply With QuoteReply With Quote
Old 12-03-2020, 12:28 AM #3
firemanj92 firemanj92 is offline
Member
 
Join Date: Apr 2017
Location: SF Bay Area, CA
Posts: 150
firemanj92 is on a distinguished road
firemanj92 firemanj92 is offline
Member
 
Join Date: Apr 2017
Location: SF Bay Area, CA
Posts: 150
firemanj92 is on a distinguished road
Quote:
Originally Posted by tgreenwood75 View Post
Hey All,

I have an '01 T4R with the "updated" steering rack guide (i.e. 24mm hex to remove) that I would like to tighten up a bit to see if it improves slight steering play. I have already tack welded the shaft and this seems like another area to gain a little bit more response and reduce the amount that the truck gets pushed around by wind.

My problem is that I am unable to loosen the lock nut/ring that puts the guide cap under tension. I have soaked it pretty good with penetrating oil but its been no match for 20yrs and 230k miles of New England driving. It is corroded but not horribly so, but I suspect it has never been removed.

Has anyone else had this problem? What's the safest way to remove it? Is a torch safe on the rack housing with the fluid and seals inside? Can the nut be cut in such a way to allow for a nailset/screwdriver removal? Keep soaking with WD40 and give up if it doesn't move?

I would love to tighten up the guide a few degrees but its not worth hurting anything expensive on a silly lock ring.

Thanks!

I had to use a pipe wrench on one of our T4R's to break it loose.
firemanj92 is offline   Reply With QuoteReply With Quote
Old 12-03-2020, 01:26 PM #4
Kanoe's Avatar
Kanoe Kanoe is offline
Senior Member
 
Join Date: Dec 2013
Location: Yukon
Posts: 1,317
Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice
Kanoe Kanoe is offline
Senior Member
Kanoe's Avatar
 
Join Date: Dec 2013
Location: Yukon
Posts: 1,317
Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice
Quote:
Originally Posted by firemanj92 View Post
I had to use a pipe wrench on one of our T4R's to break it loose.
My tool of choice for the job as well. Then I put on a new clean lock ring.
__________________
-1996 4Runner. 3RZ 5-Spd. 4x4 Base model. OME2906/Toyota OEM rears with 2004 Tacoma Dual Rate Fronts on Bilstien 4600s.
-1993 Corolla Wagon 7AFE
-2001 Echo D.D.
Kanoe is offline   Reply With QuoteReply With Quote
Old 12-03-2020, 01:43 PM #5
Malcolm99's Avatar
Malcolm99 Malcolm99 is offline
Member
 
Join Date: May 2020
Location: Ontario
Posts: 424
Malcolm99 has a spectacular aura about Malcolm99 has a spectacular aura about
Malcolm99 Malcolm99 is offline
Member
Malcolm99's Avatar
 
Join Date: May 2020
Location: Ontario
Posts: 424
Malcolm99 has a spectacular aura about Malcolm99 has a spectacular aura about
Ya a pipe wrench for sure, but you can just loosen the fitting first and then adjust the lock ring.
__________________
99' Ltd E-locker grey wired, 4R Bilstein 5100, 99 tall coils, 906 OME & 1.5" spacers, 2015 4R Trail Edition 275/70R17, 1" RB BL
97' SR5 E-locker grey wired, Warn winch, 2" RB BL, Sonoran Steel 1.2 lift, dual battery, 1000W inverter, Hydraulic Arctic plow, 12" x 33" Baja Claw
92' Eclipse GSX AWD 6/4 bolt combo, 28 PSI boost, Meth injection, 750cc injectors, FMIC, 2.5" IC piping, full 3" exhaust, 350AWHP, lowered, Alum flywheel, 6 puck Clutch, Cams, JDM gear set,VC rear diff, EPROM ECU
Malcolm99 is offline   Reply With QuoteReply With Quote
Old 12-03-2020, 05:39 PM #6
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
Quote:
Originally Posted by Malcolm99 View Post
Ya a pipe wrench for sure, but you can just loosen the fitting first and then adjust the lock ring.
Could you explain this? By "loosen the fitting" you mean to back out the guide to relieve the pressure on the lock ring? This was one of my ideas.
tgreenwood75 is offline   Reply With QuoteReply With Quote
Old 12-03-2020, 05:40 PM #7
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
Quote:
Originally Posted by Dom8706 View Post
Just out of curiosity how much torque do you think you are using trying to remove it? Are you using a hex socket on a breaker bar or a hex allen wrench?

I know those guides are only suppose to be torqued to 18 FT LB so it shouldnt need much but like you said after years of not moving it could be rusted up pretty well. Either way if it was me id use a cheater bar to get as much length as possible for better leverage. 24mm is a big hex so i dont foresee any stripping or issues from giving it a good amount of torque. Id personally stay away from using heat in that area but other people might say different.

Im actually going to be doing the exact same thing this weekend for the same reason. Let me know how big of a difference it made if you can. Im trying to track down my freeway wondering.
I'll keep you updated as soon as I break mine free, should be a quick and easy job barring this obstacle!
tgreenwood75 is offline   Reply With QuoteReply With Quote
Old 12-03-2020, 07:09 PM #8
Kanoe's Avatar
Kanoe Kanoe is offline
Senior Member
 
Join Date: Dec 2013
Location: Yukon
Posts: 1,317
Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice
Kanoe Kanoe is offline
Senior Member
Kanoe's Avatar
 
Join Date: Dec 2013
Location: Yukon
Posts: 1,317
Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice
Quote:
Originally Posted by tgreenwood75 View Post
I'll keep you updated as soon as I break mine free, should be a quick and easy job barring this obstacle!
If you are not wanting to get the whole shiterie out you may just be able to tighten the center cap a bit. Get your socket on it and tighten it in a touch. Likely an 1/8 of an inch on the circumference is all you are going to want to tighten it anyway. The steering feel will tighten up fast. Go too far and you’ll be backing off again.
__________________
-1996 4Runner. 3RZ 5-Spd. 4x4 Base model. OME2906/Toyota OEM rears with 2004 Tacoma Dual Rate Fronts on Bilstien 4600s.
-1993 Corolla Wagon 7AFE
-2001 Echo D.D.
Kanoe is offline   Reply With QuoteReply With Quote
Old 12-03-2020, 07:20 PM #9
gamefreakgc's Avatar
gamefreakgc gamefreakgc is offline
Elite Member
 
Join Date: Oct 2014
Location: Citrus Heights, California
Age: 36
Posts: 7,330
Real Name: Jerod
gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future
gamefreakgc gamefreakgc is offline
Elite Member
gamefreakgc's Avatar
 
Join Date: Oct 2014
Location: Citrus Heights, California
Age: 36
Posts: 7,330
Real Name: Jerod
gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future gamefreakgc has a brilliant future
Mine even with no rust was also insanely hard to remove. Road grime I guess. I ended up removing the guide and the ring came off with it, also with a breaker bar.
__________________
'98 4Runner SR5 - 4x4 JDM 5VZ-FE Supercharged - 249K miles.
326WHP 347TQ

AEM F/IC 6, 11 PSI, 3" Intake and 3" Exhaust
Jerod's Supercharged T[u]RD Build
gamefreakgc is offline   Reply With QuoteReply With Quote
Old 12-04-2020, 06:26 PM #10
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
So, I was able to break it free with a pipe wrench (had to pull the skidplate bolts and push it downward first) and tighten the guide a bit.

I tightened it about 10 degrees and felt no difference so I went a bit further and that was too tight, had some sticky spots in returning to center. I backed it out a touch and will try again in the morning to see how it feels. Definitely a trial-and-error scenario where it is easy to convince yourself that a touch tighter is better not worse.

For those who haven't done this yet, definitely mark the guide and the housing with a sharpie to get an idea of how far you are turning. Also, ensure that the guide doesnt get tightened when you snug down the lock ring, I think this contributed to mine being overtightened the first time.
tgreenwood75 is offline   Reply With QuoteReply With Quote
Old 12-04-2020, 07:11 PM #11
Kanoe's Avatar
Kanoe Kanoe is offline
Senior Member
 
Join Date: Dec 2013
Location: Yukon
Posts: 1,317
Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice
Kanoe Kanoe is offline
Senior Member
Kanoe's Avatar
 
Join Date: Dec 2013
Location: Yukon
Posts: 1,317
Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice Kanoe is just really nice
[QUOTE=tgreenwood75;3575449Also, ensure that the guide doesnt get tightened when you snug down the lock ring, I think this contributed to mine being overtightened the first time.[/QUOTE]

Yes, it's a 2 handed job. Ratchet in the center and wrench on the lock ring.
__________________
-1996 4Runner. 3RZ 5-Spd. 4x4 Base model. OME2906/Toyota OEM rears with 2004 Tacoma Dual Rate Fronts on Bilstien 4600s.
-1993 Corolla Wagon 7AFE
-2001 Echo D.D.
Kanoe is offline   Reply With QuoteReply With Quote
Old 12-12-2020, 07:54 PM #12
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
tgreenwood75 tgreenwood75 is offline
Member
 
Join Date: Dec 2016
Posts: 111
tgreenwood75 is on a distinguished road
Just wanted to update this for others to say that I was extremely happy with the results.

Not sure of how many degrees in total I tightened mine because I tweaked it a few times and the lock ring was hiding my initial sharpie markings.

The result is better stability in windy conditions and slightly less bump steer. The steering overall feels much nicer, could not be more pleased for the minimal effort. Amazing that a 230k mile vehicle can drive so tight and nicely without completely overhauling suspension and steering - very impressive. I would add this to the list of considerations for new owners before R&Ring the whole front end.
tgreenwood75 is offline   Reply With QuoteReply With Quote
Reply

Tags
guide , lock , rack , steering , tighten

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Excessive play on drivers side steering - replace steering rack guide cheeser 3rd gen T4Rs 17 05-05-2022 08:15 PM
Solid rack guide update in steering rack needs continual adjustment floatingkiwi 3rd gen T4Rs 13 03-20-2017 01:04 PM
New style rack guide $50 plus shipping. SoCal. JBurt For Sale: T4R Items 1 08-03-2015 07:22 PM
FS: Newer style Rack Guide parts - Reno, NV $50 shipped Dinabox For Sale: T4R Items 11 09-30-2013 11:11 AM
New Style Steering Rack Guide Dous For Sale: T4R Items 5 05-01-2013 09:06 PM

Powered by vBadvanced CMPS v3.2.2

All times are GMT -4. The time now is 05:14 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger
 
Copyright © 2020