05-04-2021, 12:44 AM
|
#1
|
Member
|
|
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
|
Member
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
A/T oil temperature light: what temperature?
I have a 2002 4runner. At what temperature will the a/t trans temp light come on. Does it state this temperature somewhere in the FSM somewhere. Has anyone verified it with an actual analog gauge or anything like that? In the FSM I have it states to check the temp sensor resistance at 68 degrees and 230 degrees Fahrenheit, does that mean the light comes on at 230 degrees?
I was in deep sand the other weekend on the beach and my light came on and I immediately shut the truck down. I realize now I should have let it idle but I did not know any better at the time. I literally shut it off about 10 seconds after the light came on. I started the truck back up a short while later and drove away like nothing happened, light was off and never came back on. I lowered the PSI in tires some more and the truck was driving a lot easier through the sand, trans was not working so hard. I checked the fluid and it is still a bright red color and smells just like tranny fluid. It is Valvoline Max-Life trans fluid...probably less than 2000 miles on the fluid as well. I changed it not too long ago, the 4Runner is not my main vehicle. I was going to change the fluid but it looks brand new, and I also read that Maxlife can withstand high temperatures (280 degrees) with no issue. Was looking for some more detailed info for when that gauge lights up.
|
|
Reply With Quote
|
05-04-2021, 01:04 AM
|
#2
|
|
Senior Member
|
|
Join Date: May 2019
Location: Northern California
Posts: 1,685
Real Name: Blair
|
|
Senior Member
Join Date: May 2019
Location: Northern California
Posts: 1,685
Real Name: Blair
|
I don't know the answer, but on an extended off road trip (climbing a few thousand feet), I got my UltraGauge trans temp up to 249 and the dash light did not trigger. I can see the bulb works at start up. I gave it a 30 min rest and never saw those heights again, but will be adding a dedicated trans cooler in series as soon as I get a chance.
__________________
260K - Y2K/E - Clock still works
|
|
Reply With Quote
|
05-04-2021, 01:13 AM
|
#3
|
Member
|
|
Join Date: Sep 2020
Location: Ohio
Posts: 507
|
|
Member
Join Date: Sep 2020
Location: Ohio
Posts: 507
|
Stating the obvious but did you make sure it's right at the correct level? I don't think it should be triggering the a/t temp light on unless it was very rough to roll in the sand.
__________________
2000 4Runner Limited 4x4 V6
|
|
Reply With Quote
|
05-04-2021, 08:06 AM
|
#4
|
Member
|
|
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
|
Member
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
Quote:
Originally Posted by FD7683
Stating the obvious but did you make sure it's right at the correct level? I don't think it should be triggering the a/t temp light on unless it was very rough to roll in the sand.
|
Good idea. I will check the level again but I am pretty sure it was spot on when I exchanged the fluid.
The thing with beach sand (at least in my area) is that it is like driving through sugar and it takes some effort. You basically follow the existing ruts and it is a couple inches deep most of the time. The tires are pushing up against the side of the existing ruts, the truck is moving slow, only in gear 2 most of the time, and the torque converter never locks up. You have to give it just enough throttle to stay moving at a pace. If you give it too much throttle the tires just fight the sand and you don't go any faster, this is what I was doing. It was my first time out this year and I wasn't paying attention to the driving method, also I didn't air down enough.
I didn't really think it was that big of a deal if the light came on for a second. But then I searched on the forum and there was a lot of doom and gloom!
|
|
Reply With Quote
|
05-04-2021, 09:20 AM
|
#5
|
Member
|
|
Join Date: Feb 2021
Location: PA
Posts: 61
|
|
Member
Join Date: Feb 2021
Location: PA
Posts: 61
|
IIRC, it's somewhere in the 270-290 range. Basically right before it starts blowing out of the vent tube.
I think I saw that on another forum so take it with a grain of salt.
Personally I've never seen the light come on but I've never had it over 220 or so.
|
|
Reply With Quote
|
05-04-2021, 09:45 AM
|
#6
|
|
Senior Member
|
|
Join Date: Sep 2011
Location: Austin, Texas
Posts: 3,151
|
|
Senior Member
Join Date: Sep 2011
Location: Austin, Texas
Posts: 3,151
|
Quote:
Originally Posted by NJ-4Runner
... At what temperature will the a/t trans temp light come on. ...
|
It is a very high number, like others said upper 200s, closer to 300, way too high, hence they call it an 'idiot' light.
Did you pull trans dipstick to have a look at the color? If on just a tiny bit probably won't make much difference but everything affects everything, in a trans anyway.
Might even do a quick drain/fill.
If you have 4x4, I'd use it in 4Lo next time on the sand or going really slow. You can start in 2nd gear and avoid the hard 1-2 shift in 4Lo on 01-02s, another feature!
Luck.
__________________
2001 Limited 4WD - 346+K - SunfireRed\Thunder Cloud; - 265/75/16 Michelin A/T2s - Fat Pat's 1.5" BL - StopTech ANGLED rotors - In series 699 trans cooler, New Yota1 transmission, All new OEM suspension front to rear.
|
|
Reply With Quote
|
05-04-2021, 09:55 AM
|
#7
|
Member
|
|
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
|
Member
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
Quote:
Originally Posted by jgue467
It is a very high number, like others said upper 200s, closer to 300, way too high, hence they call it an 'idiot' light.
Did you pull trans dipstick to have a look at the color? If on just a tiny bit probably won't make much difference but everything affects everything, in a trans anyway.
Might even do a quick drain/fill.
If you have 4x4, I'd use it in 4Lo next time on the sand or going really slow. You can start in 2nd gear and avoid the hard 1-2 shift in 4Lo on 01-02s, another feature!
Luck.
|
I did check the fluid. The trans fluid is red in color and looks like it just came out of the bottle. Smells as good as transmission fluid could.
Thanks for the tip with the 2nd gear. I know practically nothing about auto transmissions. I am 43 years old and this is the first 4x4 (or vehicle for that matter) with an automatic transmission I have ever owned. I always had manuals, after this I feel like I don't know how to use the auto properly. I know that sounds silly but it's true. I actually don't mind the auto in the woods, it is nice to not be on the clutch all the time. But the heat thing is a buzzkill.
If I put the trans in 2 and the transfer case in Lo like you said does the torque converter ever lock up?
|
|
Reply With Quote
|
05-04-2021, 10:45 AM
|
#8
|
Member
|
|
Join Date: Dec 2015
Location: Manitoba, Canada
Posts: 905
|
|
Member
Join Date: Dec 2015
Location: Manitoba, Canada
Posts: 905
|
My records show that the A/T temp light comes on at 302 F and goes out when it falls back to 248 F. I can't find where I got that info though.
In any case, the resistance tests in the FSM for 68F and 230F is to test the sensor. It assumes if the values are correct at those two points the sensor is good.
It's not practical to test the sensor over 230F in a shop.
__________________
2000 4runner 4wd Auto V6 - Tru-Cool LPD4454 trans cooler in series
1991 4runner 4wd Auto V6
1990 4runner 4wd Auto V6
|
|
Reply With Quote
|
05-04-2021, 11:51 AM
|
#9
|
Elite Member
|
|
Join Date: Mar 2016
Location: Pasadena, CA
Posts: 5,411
|
|
Elite Member
Join Date: Mar 2016
Location: Pasadena, CA
Posts: 5,411
|
Quote:
Originally Posted by NJ-4Runner
If I put the trans in 2 and the transfer case in Lo like you said does the torque converter ever lock up?
|
No, but in 4LO, you don't really need to lock the torque converter. Low in the transfer case really lowers the load on the engine/torque converter/transmission (by 2.7x).
Depending on speed, you might find that in 4LO that you'll run in 3rd (OD off) with the torque converter locked in sand.
-Charlie
__________________
'99 4Runner SR5 Auto - 4WD swapped
'89 Camry Alltrac LE 3S-GTE 5spd
'17 Chevy Volt Premier
'16 Honda Odyssey Elite
Previous: '88 Camry Alltrac LE 3S-GE BEAMS, 90 Camry 3S-GTE, 90 Camry DX, '03 WRX wagon, '08 Outback XT
|
|
Reply With Quote
|
05-04-2021, 01:07 PM
|
#10
|
Member
|
|
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
|
Member
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
Quote:
Originally Posted by alumarine
My records show that the A/T temp light comes on at 302 F and goes out when it falls back to 248 F. I can't find where I got that info though.
In any case, the resistance tests in the FSM for 68F and 230F is to test the sensor. It assumes if the values are correct at those two points the sensor is good.
It's not practical to test the sensor over 230F in a shop.
|
Good answer. Thanks!
Quote:
Originally Posted by phattyduck
No, but in 4LO, you don't really need to lock the torque converter. Low in the transfer case really lowers the load on the engine/torque converter/transmission (by 2.7x).
Depending on speed, you might find that in 4LO that you'll run in 3rd (OD off) with the torque converter locked in sand.
-Charlie
|
Super good advice. Thanks!
|
|
Reply With Quote
|
05-04-2021, 01:39 PM
|
#11
|
Senior Member
|
|
Join Date: May 2015
Location: north east of Fairbank out there in the frontiers Alaska
Posts: 3,167
Real Name: 3 Bears
|
|
Senior Member
Join Date: May 2015
Location: north east of Fairbank out there in the frontiers Alaska
Posts: 3,167
Real Name: 3 Bears
|
lots of good advice above.
I too was not that fammiliar with automatics in a 4wd till I got my 2000 ( now have a 2001) While I never did trigger my trans light....what really got my attention...and thus changed my driving habits ...was when i got my OBD2 reader and torque pro for my phone. YOu can watch the temps in real time. That phone app as well as advice here and I think timmy has a video on trans temps and driving off road helped improve my off road habits alot.
side note.....after moving to alaska i also saw how cold my tranny was running...which is bad too...so I then went back and hooked my external cooler back in series to help warm up my tranny fluid.....and also put on a tranny heater so then my rig had a block heater as well as a tranny pan heater.
__________________
2000 SR-5 Highlander version 4:30's, factory locker , green, bought 6/21
2001 SR-5... bought 11/20..sold 6/21....
2000 SR-5 moded, lifted, e locker, other cool stuff, totaled 10/20
|
|
Reply With Quote
|
05-04-2021, 10:48 PM
|
#12
|
|
Senior Member
|
|
Join Date: Sep 2011
Location: Austin, Texas
Posts: 3,151
|
|
Senior Member
Join Date: Sep 2011
Location: Austin, Texas
Posts: 3,151
|
Quote:
Originally Posted by NJ-4Runner
.. But the heat thing is a buzzkill.
If I put the trans in 2 and the transfer case in Lo like you said does the torque converter ever lock up?
|
Right on the buzzkill, 4Lo will keep trans cooler in low speed driving.
Starting on 2 in 4Lo will allow vehicle to go about 20 before it shifts to 3rd but I never drive that fast off-road when I need 4Lo, so I'm always in 2.
Try taking off from 0 in 4Lo in first gear, when you hit about 10 you'll see what I mean about the hard 1-2 shift and probably won't like it. I only use 4Lo in sand or crawling slowly uphills in rocky terrain the rest of the time she's in 4Hi with center diff locked (really helps on deep mud and snow/ice).
__________________
2001 Limited 4WD - 346+K - SunfireRed\Thunder Cloud; - 265/75/16 Michelin A/T2s - Fat Pat's 1.5" BL - StopTech ANGLED rotors - In series 699 trans cooler, New Yota1 transmission, All new OEM suspension front to rear.
|
|
Reply With Quote
|
05-05-2021, 05:19 AM
|
#13
|
Junior Member
|
|
Join Date: Nov 2019
Location: Smithfield, NC
Posts: 10
|
|
Junior Member
Join Date: Nov 2019
Location: Smithfield, NC
Posts: 10
|
Hi NJ4Runner,
I have been driving the beaches of Cape Hatteras Sea Shore for the past 20 years. It has some notorious soft sand, especially entering and exiting the access ramps.
I have owned my stock 2000 4Runner since 2001. I air down to 17 lbs and have never been stuck. Driving and navigating soft sand is all about tire pressure, staying in the ruts, and avoiding the wet red sand.
I also monitor my tranny temps with a ultraguage. I use 4hi and never see temps exceeding 185-190.
SeaCreechur
|
|
Reply With Quote
|
05-05-2021, 08:23 AM
|
#14
|
|
Senior Member
|
|
Join Date: Mar 2016
Location: West Bend, WI
Posts: 2,339
Real Name: Mike
|
|
Senior Member
Join Date: Mar 2016
Location: West Bend, WI
Posts: 2,339
Real Name: Mike
|
Wow, nice fish. That sheepshead is massive!
__________________
1997 SR5 4x4 Auto, 99' tall coils up front, OME 906's, Truetrac LSD, Airaid MIT
1999 SR5 4x4 Auto for parts
2011 Camry SE V6
2011 Highlander Limited
|
|
Reply With Quote
|
05-05-2021, 10:48 AM
|
#15
|
Member
|
|
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
|
Member
Join Date: Jun 2020
Location: NJ Pine Barrens
Posts: 107
|
Quote:
Originally Posted by jgue467
Right on the buzzkill, 4Lo will keep trans cooler in low speed driving.
Starting on 2 in 4Lo will allow vehicle to go about 20 before it shifts to 3rd but I never drive that fast off-road when I need 4Lo, so I'm always in 2.
Try taking off from 0 in 4Lo in first gear, when you hit about 10 you'll see what I mean about the hard 1-2 shift and probably won't like it. I only use 4Lo in sand or crawling slowly uphills in rocky terrain the rest of the time she's in 4Hi with center diff locked (really helps on deep mud and snow/ice).
|
Quote:
Originally Posted by SeaCreechur
Hi NJ4Runner,
I have been driving the beaches of Cape Hatteras Sea Shore for the past 20 years. It has some notorious soft sand, especially entering and exiting the access ramps.
I have owned my stock 2000 4Runner since 2001. I air down to 17 lbs and have never been stuck. Driving and navigating soft sand is all about tire pressure, staying in the ruts, and avoiding the wet red sand.
I also monitor my tranny temps with a ultraguage. I use 4hi and never see temps exceeding 185-190.
SeaCreechur
|
That's awesome.
After some digging I think I know what some of my problem is. I have Mickey Thompson MTZ P3 Mud Terrain tires. They are 265/75 R16 load range E. These are small load range E tires. When I air down to 18 PSI the tires are not even squatting, it is not enough and the tires are digging in too much. They are fighting me in the sand at that PSI and my natural reaction was to add throttle which is the wrong move. I think I have to drop down to more like 15 PSI, or lower to even begin to float on top of the sand. I used to have 31x10.5 load range C tires and they behaved very differently at 18 PSI.
The next question is how the hell have you been driving that 4Runner on an east coast beach for 20 years and it is not a pile of rust and rubber! The beach is straight up vehicle killer. I knew I would be taking mine on the beach and when I bought the truck I pretty much knew that it is a sacrifice. We have guys up here that simply lease jeeps, drive them on the beach for 4 years, and turn them in with substantial rust. do you wash it after every beach run? Are you on the beach often?
|
|
Reply With Quote
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
|