11-20-2021, 12:29 PM
|
#1
|
 |
Member
|
|
Join Date: Aug 2015
Location: High desert, CA
Posts: 480
|
|
|
Member
Join Date: Aug 2015
Location: High desert, CA
Posts: 480
|
Do sequoia spindles fit?
I had a friend part out a 2wd 2002 Sequoia with less than 90k miles and I ended up with the front suspension pieces for free. Pretty sure my front wheel bearing are starting to grumble and get loud so I was wondering if anyone knew if the Sequoia spindles I have are the same or compatible as the 4runner? It would be much easier for me to just swap both spindles than deal with pressing bearings on and off
__________________
'99 4Runner SR5: 5VZ, 2wd, AT, 400k+ club
'94 Pickup: 2wd, 22RE, 5spd, (3RZ swap in progress)
Front: Total Chaos Uniball Kit, Fox 2.5 8'' coilover
Rear: Deaver F67 Leaf Springs, Fox 2.0 14'' Reservoir Shocks, E-locker Axle 4.88 Gears 33x10.5 BFG ATs
|
|
 Reply With Quote
|
|
11-20-2021, 01:51 PM
|
#2
|
|
Senior Member
|
|
Join Date: Feb 2019
Location: Hot Springs, AR
Posts: 4,410
Real Name: Patrick
|
|
|
Senior Member
Join Date: Feb 2019
Location: Hot Springs, AR
Posts: 4,410
Real Name: Patrick
|
Quote:
Originally Posted by Twisted Sid
I had a friend part out a 2wd 2002 Sequoia with less than 90k miles and I ended up with the front suspension pieces for free. Pretty sure my front wheel bearing are starting to grumble and get loud so I was wondering if anyone knew if the Sequoia spindles I have are the same or compatible as the 4runner? It would be much easier for me to just swap both spindles than deal with pressing bearings on and off
|
I'm 99 percent sure they do not interchange. Sequoia spindles would be closer to Tundra spindles than 4Runners.
EDIT: I'm wrong. Learn something new every day!
__________________
2000 SR5 V6 Manual 4WD https://www.toyota-4runner.org/3rd-g...biography.html
2000 Limited V6 Auto E-Locker Sold 3/2022
Last edited by Bad Luck; 11-22-2021 at 09:44 AM.
|
|
|
Reply With Quote
|
|
11-20-2021, 02:01 PM
|
#3
|
 |
Senior Member
|
|
Join Date: Apr 2011
Location: Oceanside, CA
Posts: 1,892
Real Name: Evan
|
|
|
Senior Member
Join Date: Apr 2011
Location: Oceanside, CA
Posts: 1,892
Real Name: Evan
|
Quote:
Originally Posted by Bad Luck
I'm 99 percent sure they do not interchange. Sequoia spindles would be closer to Tundra spindles than 4Runners.
|
I was going to say the opposite. I think they’re all the same, as well as the front diffs. I believe the a arms, tie rods and ball joints are what’s different.
__________________
2000 Black Sport 4WD 5spd -JD Fabrication long travel/ Fox 2.5 8” RR/ Anonymous Fab lower uniball• McNeil Racing fenders • Toytec Superflex/ 5th gen Bilstein 5100/ Wheelers Superbumps • 315/70/17 BFG KO2 on Robby Gordon wheels • 231mm TBU / Wheelers SS lines • MStudt rear swaybar links • Tom Woods driveshaft • Satoshi • K&N FIPK w/ AFE dry filter • Borla Pro XS • URD short throw shifter & Ellis Precision shift knobs • Uniden PRO 520XL & 3' Firefly on custom mount• Prinsu full rack • Baja Designs Squadron Sport Sae & combo beam lights • Paranoid Fab switch panel with Ram mounts • Extended rear diff breather • 01-02 tail lights • Stubbs HD-SKO sliders • Any 7 Offroad gas tank skid • @Assburns custom tube front bumper • Nguyen Works swing out bumper • FROR rear links
|
|
|
Reply With Quote
|
|
11-20-2021, 02:13 PM
|
#4
|
|
Senior Member
|
|
Join Date: Apr 2011
Location: Oceanside, CA
Posts: 1,892
Real Name: Evan
|
|
|
Senior Member
Join Date: Apr 2011
Location: Oceanside, CA
Posts: 1,892
Real Name: Evan
|
Spindle gussets from various manufacturers all show that they fit Tacoma, 4Runner and Tundra of similar years. Solo Motorsports has fabricated spindles that say they fit all 3 also, which would imply that there are no differences.
Toyota Full Fabricated Spindles - Solo Motorsports
__________________
2000 Black Sport 4WD 5spd -JD Fabrication long travel/ Fox 2.5 8” RR/ Anonymous Fab lower uniball• McNeil Racing fenders • Toytec Superflex/ 5th gen Bilstein 5100/ Wheelers Superbumps • 315/70/17 BFG KO2 on Robby Gordon wheels • 231mm TBU / Wheelers SS lines • MStudt rear swaybar links • Tom Woods driveshaft • Satoshi • K&N FIPK w/ AFE dry filter • Borla Pro XS • URD short throw shifter & Ellis Precision shift knobs • Uniden PRO 520XL & 3' Firefly on custom mount• Prinsu full rack • Baja Designs Squadron Sport Sae & combo beam lights • Paranoid Fab switch panel with Ram mounts • Extended rear diff breather • 01-02 tail lights • Stubbs HD-SKO sliders • Any 7 Offroad gas tank skid • @Assburns custom tube front bumper • Nguyen Works swing out bumper • FROR rear links
|
|
|
Reply With Quote
|
|
11-20-2021, 07:53 PM
|
#5
|
|
Member
|
|
Join Date: Aug 2015
Location: High desert, CA
Posts: 480
|
|
|
Member
Join Date: Aug 2015
Location: High desert, CA
Posts: 480
|
Quote:
Originally Posted by Dezert4Runner
Spindle gussets from various manufacturers all show that they fit Tacoma, 4Runner and Tundra of similar years. Solo Motorsports has fabricated spindles that say they fit all 3 also, which would imply that there are no differences.
Toyota Full Fabricated Spindles - Solo Motorsports |
I thought the same thing and these exact reasons are why I asked. I didn't want to tear it all down to find out it's off by 10mm in some critical area and screws up alignment
__________________
'99 4Runner SR5: 5VZ, 2wd, AT, 400k+ club
'94 Pickup: 2wd, 22RE, 5spd, (3RZ swap in progress)
Front: Total Chaos Uniball Kit, Fox 2.5 8'' coilover
Rear: Deaver F67 Leaf Springs, Fox 2.0 14'' Reservoir Shocks, E-locker Axle 4.88 Gears 33x10.5 BFG ATs
|
|
|
Reply With Quote
|
|
11-21-2021, 04:14 AM
|
#6
|
 |
Member
|
|
Join Date: May 2004
Location: Mideast
Posts: 977
|
|
|
Member
Join Date: May 2004
Location: Mideast
Posts: 977
|
for 1999-2002 Tundra,the part numbers are the same as those of the 4Runner, after that the part numbers are different:
LH - 43202-35070/71 (ABS)
RH - 43201-35080/81 (ABS)
dunno why they changed part numbers. perhaps the newer ones are Made in the USA?
|
|
|
Reply With Quote
|
|
11-22-2021, 09:45 AM
|
#7
|
|
Senior Member
|
|
Join Date: Feb 2019
Location: Hot Springs, AR
Posts: 4,410
Real Name: Patrick
|
|
|
Senior Member
Join Date: Feb 2019
Location: Hot Springs, AR
Posts: 4,410
Real Name: Patrick
|
Quote:
Originally Posted by Dezert4Runner
I was going to say the opposite. I think they’re all the same, as well as the front diffs. I believe the a arms, tie rods and ball joints are what’s different.
|
Well that's good to know. I wonder if the bearings are the same and you can use the entire spindle minus the lower ball joint?
__________________
2000 SR5 V6 Manual 4WD https://www.toyota-4runner.org/3rd-g...biography.html
2000 Limited V6 Auto E-Locker Sold 3/2022
|
|
|
Reply With Quote
|
|
11-22-2021, 10:01 AM
|
#8
|
|
Member
|
|
Join Date: May 2004
Location: Mideast
Posts: 977
|
|
|
Member
Join Date: May 2004
Location: Mideast
Posts: 977
|
only the 2001-2002 Tundra front axle hub bearings are the same as those of the 1996-2002 4Runner
|
|
|
Reply With Quote
|
|
11-24-2021, 12:20 AM
|
#9
|
|
Member
|
|
Join Date: Aug 2015
Location: High desert, CA
Posts: 480
|
|
|
Member
Join Date: Aug 2015
Location: High desert, CA
Posts: 480
|
Well damn, i appreciate eveeryones replys but i was wrong and the sequoia was an '05 🙄. Anyone know what is different about them?
__________________
'99 4Runner SR5: 5VZ, 2wd, AT, 400k+ club
'94 Pickup: 2wd, 22RE, 5spd, (3RZ swap in progress)
Front: Total Chaos Uniball Kit, Fox 2.5 8'' coilover
Rear: Deaver F67 Leaf Springs, Fox 2.0 14'' Reservoir Shocks, E-locker Axle 4.88 Gears 33x10.5 BFG ATs
|
|
|
Reply With Quote
|
|
11-24-2021, 12:27 AM
|
#10
|
 |
Senior Member
|
|
Join Date: Apr 2020
Location: Monroe, WA
Posts: 2,197
Real Name: Devan
|
|
|
Senior Member
Join Date: Apr 2020
Location: Monroe, WA
Posts: 2,197
Real Name: Devan
|
Damn, read this thread in it's beginning and was also hoping this was the case. Why Toyota didn't just offer bolt on hubs is beyond me, life would be so much easier that way 
__________________
Y2K Highlander Millennium Silver 3.4L auto @ 320k and climbing 
Toytecs + 5100s / 7.5 wrap + OME spacers + Tokicos / JBA UCAs / Anonymous Fab. LBJs / Total Chaos Gussets / EimKeith PCK + LCAR / Extended Bump Stops; Brake Lines; Rear Diff Breather / True North Fab. Hybrid Bumper / CBI Hybrid Bumper + Tire Carrier / 4xInnovations Hybrid Sliders / Opt Offroad Trailing Arms / Lil Skip Gas Skid / BudBuilt Front Skid / ARB Rear Locker
|
|
Reply With Quote
|
|
11-24-2021, 12:29 AM
|
#11
|
|
Senior Member
|
|
Join Date: Apr 2011
Location: Oceanside, CA
Posts: 1,892
Real Name: Evan
|
|
|
Senior Member
Join Date: Apr 2011
Location: Oceanside, CA
Posts: 1,892
Real Name: Evan
|
First gen Sequoia is up to 2007, so those should be the same spindle too.
__________________
2000 Black Sport 4WD 5spd -JD Fabrication long travel/ Fox 2.5 8” RR/ Anonymous Fab lower uniball• McNeil Racing fenders • Toytec Superflex/ 5th gen Bilstein 5100/ Wheelers Superbumps • 315/70/17 BFG KO2 on Robby Gordon wheels • 231mm TBU / Wheelers SS lines • MStudt rear swaybar links • Tom Woods driveshaft • Satoshi • K&N FIPK w/ AFE dry filter • Borla Pro XS • URD short throw shifter & Ellis Precision shift knobs • Uniden PRO 520XL & 3' Firefly on custom mount• Prinsu full rack • Baja Designs Squadron Sport Sae & combo beam lights • Paranoid Fab switch panel with Ram mounts • Extended rear diff breather • 01-02 tail lights • Stubbs HD-SKO sliders • Any 7 Offroad gas tank skid • @Assburns custom tube front bumper • Nguyen Works swing out bumper • FROR rear links
|
|
|
Reply With Quote
|
| Thread Tools |
|
|
| Display Modes |
Rate This Thread |
 Linear Mode
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
|
