User Tag List

Reply
 
Thread Tools Rate Thread Display Modes
Old 01-04-2019, 11:05 PM #1
smokey73's Avatar
smokey73 smokey73 is offline
Member
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
smokey73 smokey73 is offline
Member
smokey73's Avatar
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
Who do you trust for a head job?

After my last trip, I noticed I had to add a little more oil than usual, almost 1/2 quart after 1500 miles. I rarely have to add more than 1/2qt between oil changes, regardless of how hard I drive it. I've been noticing the normal "puff" of smoke I see when I start it after it sits a week or more is turning into a light fog and it doesn't need to sit more than a couple days now to see it. I've been suspecting valve seals and I confirmed this today when I had the exhaust manifolds off (new cats) and saw that the valve stems were slightly wet still. This leaves me trying to decide what to do next. At 280k miles, I'm sure the engine needs some attention. I plan on keeping it for as long as possible. My thoughts are to run it till having to add oil becomes a problem. Pull the engine and do the bottom end. At that point, who would I send the heads off to? If it was an old SBC, I'd take it down to Motor Parts and let "Steve" or "Chuck" work them over in the back room for $75 a pop. That being said, I'm not sure either one of them could even spell Toyota, so would I be taking a risk letting them work these heads? Is there enough difference that I should be worried? I live in the DFW area, I'm sure there's a specialized shop somewhere that deals with them, but would it be worth it to go to them? I'm just looking for some thoughts from someone who's been through this already.
__________________
'03 Limited V8 Toytec Ultimate 3/2.5" General Grabber ATx LT275/70 R17 Rear Grizzley locker
smokey73 is offline   Reply With QuoteReply With Quote
Old 01-06-2019, 10:46 PM #2
smokey73's Avatar
smokey73 smokey73 is offline
Member
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
smokey73 smokey73 is offline
Member
smokey73's Avatar
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
Bump

Bump
__________________
'03 Limited V8 Toytec Ultimate 3/2.5" General Grabber ATx LT275/70 R17 Rear Grizzley locker
smokey73 is offline   Reply With QuoteReply With Quote
Old 01-06-2019, 10:56 PM #3
4RunnerMexico 4RunnerMexico is offline
Member
 
Join Date: Aug 2017
Location: SC
Posts: 111
4RunnerMexico is on a distinguished road
4RunnerMexico 4RunnerMexico is offline
Member
 
Join Date: Aug 2017
Location: SC
Posts: 111
4RunnerMexico is on a distinguished road
I had great success with a local machine shop. Yes, this guy usually spends his time building 1000hp GM engines, but he did a great job with my 4.0 heads. Just go visit some local people near you, most of the time people who do this type of work are honest in what they can and cant do.
4RunnerMexico is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 11:51 AM #4
wsgoat's Avatar
wsgoat wsgoat is offline
Member
 
Join Date: Oct 2008
Location: under the radar
Posts: 470
wsgoat has a spectacular aura about wsgoat has a spectacular aura about
wsgoat wsgoat is offline
Member
wsgoat's Avatar
 
Join Date: Oct 2008
Location: under the radar
Posts: 470
wsgoat has a spectacular aura about wsgoat has a spectacular aura about
I trust my girl friend.....she's a great mechanic!
__________________
*2017 4R TRD Pro, 01H5 Cement w/ Shrockworks dimpled tread plate sliders, Moroso oil catch-can, black powder-coated roof rails. (summer runner).
*2005 4R Sport Edition w/ Bilstein 5100's, Gen-5 brake upgrade, K&N cold air intake, cabin air intake mod, Falken Wildpeak AT3. (winter runner).
*1965 Pontiac GTO convertible, 4-speed w/tri-power, PHS documented. (born in Freemont CA).
*1962 Chevrolet C-10 (short-step) pickup, 4-speed, survivor. (born in Oakland CA).
wsgoat is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 12:53 PM #5
hinmo24t hinmo24t is offline
Senior Member
 
Join Date: Aug 2018
Location: MA
Posts: 1,141
hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough
hinmo24t hinmo24t is offline
Senior Member
 
Join Date: Aug 2018
Location: MA
Posts: 1,141
hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough
Quote:
Originally Posted by 4RunnerMexico View Post
I had great success with a local machine shop. Yes, this guy usually spends his time building 1000hp GM engines, but he did a great job with my 4.0 heads. Just go visit some local people near you, most of the time people who do this type of work are honest in what they can and cant do.
funny you mention this - i had a similar experience.

my wrx timing belt snapped over seized waterpump WHILE DRIVING and bent every valve...i coasted into a domestic performance shop and ironically
they did a kickass job of new valves on the turbo jap car.
hinmo24t is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 12:54 PM #6
hinmo24t hinmo24t is offline
Senior Member
 
Join Date: Aug 2018
Location: MA
Posts: 1,141
hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough
hinmo24t hinmo24t is offline
Senior Member
 
Join Date: Aug 2018
Location: MA
Posts: 1,141
hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough hinmo24t is a jewel in the rough
Quote:
Originally Posted by wsgoat View Post
I trust my girl friend.....she's a great mechanic!
lmao i initially opened this thread to see if the title was a joke and it wasn't so i left - thanks for taking the plunge.

op - good luck with the head!
hinmo24t is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 02:39 PM #7
duffdog duffdog is offline
Member
 
Join Date: Mar 2015
Location: Sacramento CA
Posts: 683
duffdog is a jewel in the rough duffdog is a jewel in the rough duffdog is a jewel in the rough
duffdog duffdog is offline
Member
 
Join Date: Mar 2015
Location: Sacramento CA
Posts: 683
duffdog is a jewel in the rough duffdog is a jewel in the rough duffdog is a jewel in the rough
Quote:
Originally Posted by smokey73 View Post
After my last trip, I noticed I had to add a little more oil than usual, almost 1/2 quart after 1500 miles. I rarely have to add more than 1/2qt between oil changes, regardless of how hard I drive it. I've been noticing the normal "puff" of smoke I see when I start it after it sits a week or more is turning into a light fog and it doesn't need to sit more than a couple days now to see it. I've been suspecting valve seals and I confirmed this today when I had the exhaust manifolds off (new cats) and saw that the valve stems were slightly wet still. This leaves me trying to decide what to do next. At 280k miles, I'm sure the engine needs some attention. I plan on keeping it for as long as possible. My thoughts are to run it till having to add oil becomes a problem. Pull the engine and do the bottom end. At that point, who would I send the heads off to? If it was an old SBC, I'd take it down to Motor Parts and let "Steve" or "Chuck" work them over in the back room for $75 a pop. That being said, I'm not sure either one of them could even spell Toyota, so would I be taking a risk letting them work these heads? Is there enough difference that I should be worried? I live in the DFW area, I'm sure there's a specialized shop somewhere that deals with them, but would it be worth it to go to them? I'm just looking for some thoughts from someone who's been through this already.
Most high performance racing machine shops can handle the 2uz-fe. I wouldn't trust one of those all-in-one machine shop auto parts stores... been there, never will go back
__________________
2005 Blue SR5 v8

3" suspension lift, 1" body lift, 315's, rear Elocker, on-board air system, slider air tanks, full skid plates, front Demello bumper, rear HMF plate/tube bumper, rear 9000lb hidden winch, front 10000lb winch, dual electric fans (in cab adjustable temp), rock lights, 25W LED projector lights.
duffdog is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 08:15 PM #8
smokey73's Avatar
smokey73 smokey73 is offline
Member
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
smokey73 smokey73 is offline
Member
smokey73's Avatar
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
Quote:
Originally Posted by hinmo24t View Post
lmao i initially opened this thread to see if the title was a joke and it wasn't so i left - thanks for taking the plunge.

op - good luck with the head!
Yeah, I figured I'd try a little click bait to ramp up the views a little
__________________
'03 Limited V8 Toytec Ultimate 3/2.5" General Grabber ATx LT275/70 R17 Rear Grizzley locker
smokey73 is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 08:18 PM #9
smokey73's Avatar
smokey73 smokey73 is offline
Member
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
smokey73 smokey73 is offline
Member
smokey73's Avatar
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
Quote:
Originally Posted by wsgoat View Post
I trust my girl friend.....she's a great mechanic!
Yeah, "mechanic"
__________________
'03 Limited V8 Toytec Ultimate 3/2.5" General Grabber ATx LT275/70 R17 Rear Grizzley locker
smokey73 is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 08:20 PM #10
smokey73's Avatar
smokey73 smokey73 is offline
Member
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
smokey73 smokey73 is offline
Member
smokey73's Avatar
 
Join Date: Jun 2015
Location: Kemp, Tx
Posts: 125
Real Name: Roddy
smokey73 is on a distinguished road
Quote:
Originally Posted by duffdog View Post
Most high performance racing machine shops can handle the 2uz-fe. I wouldn't trust one of those all-in-one machine shop auto parts stores... been there, never will go back
That's the way I was leaning. Can they set the valves without the heads on the engine?
__________________
'03 Limited V8 Toytec Ultimate 3/2.5" General Grabber ATx LT275/70 R17 Rear Grizzley locker
smokey73 is offline   Reply With QuoteReply With Quote
Old 01-07-2019, 09:02 PM #11
AuSeeker AuSeeker is offline
Senior Member
 
Join Date: Nov 2016
Location: South Carolina
Posts: 4,617
Real Name: Skip
AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future
AuSeeker AuSeeker is offline
Senior Member
 
Join Date: Nov 2016
Location: South Carolina
Posts: 4,617
Real Name: Skip
AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future AuSeeker has a brilliant future
Quote:
Originally Posted by smokey73 View Post
Yeah, I figured I'd try a little click bait to ramp up the views a little
I was hesitant to reply to this topic because I didn't trust myself to post a serious reply...but my reply would have been..."my wife" she's eeerr a mechanic as well...yes that's right and she can torque my nuts!!

Quote:
Originally Posted by smokey73 View Post
That's the way I was leaning. Can they set the valves without the heads on the engine?
Unfortunately not, the heads have to be installed as well as the cams, timming belt, etc., etc., basically the engine needs to be totally put back together, then all the valve clearances have to be checked, any that aren't within tolerance will have to be "adjusted" and that's when the fun parts starts, the valves have a cap/cup on top of each valve, the cam lobes run in these cups to open the valves, and in between the cup and the valve stem there's a specific size shim, this shim is what sets the proper valve clearance, any valve that's doesn't have the proper clearance will need the shim replaced thusly "adjusting" the valve clearance, unfortunately to replace the shim for one that corrects the clearance the cup needs to be removed and to do that the cam needs to be removed, pull the cup/s and replace the shim/s with a thicker or thinner shim/s to achieve the proper valve clearance....so you check all the clearances make very accurate notes on which valves needs "adjustment" and by how much +/- and then starts the fun of taking the cam/s off pull the cup/ss, swap out shim/s and then install the cams check the clearances again and hope you took good notes and got it all right so you don't have to do it all again!

Also when the heads are removed to be reworked make sure you keep all the cups and shims organized so they go back exactly where they came off, you may get lucky and the valves when reassembled are not that far off and needs no "adjustment" but again unfortunately I doubt that will happen after the work is done on the heads/valves.
__________________
2004 Limited V8

Last edited by AuSeeker; 01-07-2019 at 09:10 PM.
AuSeeker is offline   Reply With QuoteReply With Quote
Old 01-08-2019, 02:59 PM #12
duffdog duffdog is offline
Member
 
Join Date: Mar 2015
Location: Sacramento CA
Posts: 683
duffdog is a jewel in the rough duffdog is a jewel in the rough duffdog is a jewel in the rough
duffdog duffdog is offline
Member
 
Join Date: Mar 2015
Location: Sacramento CA
Posts: 683
duffdog is a jewel in the rough duffdog is a jewel in the rough duffdog is a jewel in the rough
Quote:
Originally Posted by AuSeeker View Post
I was hesitant to reply to this topic because I didn't trust myself to post a serious reply...but my reply would have been..."my wife" she's eeerr a mechanic as well...yes that's right and she can torque my nuts!!



Unfortunately not, the heads have to be installed as well as the cams, timming belt, etc., etc., basically the engine needs to be totally put back together, then all the valve clearances have to be checked, any that aren't within tolerance will have to be "adjusted" and that's when the fun parts starts, the valves have a cap/cup on top of each valve, the cam lobes run in these cups to open the valves, and in between the cup and the valve stem there's a specific size shim, this shim is what sets the proper valve clearance, any valve that's doesn't have the proper clearance will need the shim replaced thusly "adjusting" the valve clearance, unfortunately to replace the shim for one that corrects the clearance the cup needs to be removed and to do that the cam needs to be removed, pull the cup/s and replace the shim/s with a thicker or thinner shim/s to achieve the proper valve clearance....so you check all the clearances make very accurate notes on which valves needs "adjustment" and by how much +/- and then starts the fun of taking the cam/s off pull the cup/ss, swap out shim/s and then install the cams check the clearances again and hope you took good notes and got it all right so you don't have to do it all again!

Also when the heads are removed to be reworked make sure you keep all the cups and shims organized so they go back exactly where they came off, you may get lucky and the valves when reassembled are not that far off and needs no "adjustment" but again unfortunately I doubt that will happen after the work is done on the heads/valves.

What?? I'm not sure where you are getting this information. If you take your heads to a Racing engine shop where they build Racing engines, they have all the equipment available to completely build the heads with all clearances on all valves completely set up to bolt onto the engine with proper seat pressure having never seen the block or the car at all. I do understand that there are very few shops that can do this, in Sacramento CA there are 2 shops that can do it. You could even take a random basket of head parts to them completely out of order and they will deliver to you an assembled head ready to bolt onto the engine. (That last scenario would cost you a lot of $$$$)

I have already had this done with my own engine and it is running amazingly with better gas mileage and power than before it exploded. The shop never saw the engine or the car and rebuilt my heads after a catastrophic event where the valves hit the pistons. I put them back on the engine in my backyard by myself 2 years ago and the 2uz-fe is still running great.

It doesn't have to cost a zillion dollars to rebuild a 2uz. Granted its not as simple as a domestic engine, but there are some very good shops that can handle it.
__________________
2005 Blue SR5 v8

3" suspension lift, 1" body lift, 315's, rear Elocker, on-board air system, slider air tanks, full skid plates, front Demello bumper, rear HMF plate/tube bumper, rear 9000lb hidden winch, front 10000lb winch, dual electric fans (in cab adjustable temp), rock lights, 25W LED projector lights.
duffdog is offline   Reply With QuoteReply With Quote
Old 03-21-2021, 07:10 AM #13
mmeuli mmeuli is offline
Member
 
Join Date: Jan 2019
Location: Charleston, SC
Age: 37
Posts: 51
Real Name: Michael Meuli
mmeuli is on a distinguished road
mmeuli mmeuli is offline
Member
 
Join Date: Jan 2019
Location: Charleston, SC
Age: 37
Posts: 51
Real Name: Michael Meuli
mmeuli is on a distinguished road
Quote:
Originally Posted by wsgoat View Post
I trust my girl friend.....she's a great mechanic!
Beat me to the punch!

Sent from my SM-G998U using Tapatalk
mmeuli is offline   Reply With QuoteReply With Quote
Reply

Tags
add , engine , oil , thoughts , valve

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
SPACERS: how much can you Trust em when off Roading? CrazySte Off-Roading 9 07-21-2018 12:58 AM
Do you trust your Nav? SgnDen 5th gen T4Rs 22 10-22-2012 02:30 PM
Amazon.com Don't Trust ntopliffe General Discussions 5 04-06-2012 12:31 AM
Should I trust this? Carolinafan 3rd gen T4Rs 15 05-31-2011 10:31 PM
Should You Trust the V8 Towing Spec? cmj685 4th Gen T4Rs 3 03-17-2005 10:27 AM

Powered by vBadvanced CMPS v3.2.2

All times are GMT -4. The time now is 07:19 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger
 
Copyright © 2020