User Tag List

Reply
 
Thread Tools Rate Thread Display Modes
Old 05-29-2023, 10:23 PM #1
knightsfs4's Avatar
knightsfs4 knightsfs4 is offline
Member
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
knightsfs4 knightsfs4 is offline
Member
knightsfs4's Avatar
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
Turn Signal LED Hyperflash Solution

I drive a 2006 4Runner and currently have LEDs throughout the entire vehicle. The only lights I never replaced with LEDs were the turn signals due to the hyper flash issue.

I know some people use resistors, while others have used a turn signal flash module.

My question is, what have you all done to solve this issue? Looking for a solution so I can swap in LEDs and call it a day.

Thank you in advance for all input!
__________________
Knightsfs4 Build Thread http://www.toyota-4runner.org/4th-ge...ld-thread.html
Jack-Purchased on 11/22/10- 2006 Limited 4X4 V8
knightsfs4 is offline   Reply With QuoteReply With Quote
Old 05-30-2023, 06:13 AM #2
Bluesky 07's Avatar
Bluesky 07 Bluesky 07 is online now
Senior Member
 
Join Date: Sep 2014
Location: Cherokee Co., GA
Posts: 2,691
Real Name: Russell (OB #9908)
Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of
Bluesky 07 Bluesky 07 is online now
Senior Member
Bluesky 07's Avatar
 
Join Date: Sep 2014
Location: Cherokee Co., GA
Posts: 2,691
Real Name: Russell (OB #9908)
Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of
I used resistors from Amazon secured with metal dryer duct tape (which is very handy for numerous vehicle uses btw). The resistors have screw holes but drilling sheet metal risks rust so nope on that.

It’s been almost a year and no issues. This is the passenger side; on the driver’s side, I tucked it up forward as far as possible from the battery (had the battery out for something else).



LMK if resistor and/or bulb specifics would be helpful.
Bluesky 07 is online now   Reply With QuoteReply With Quote
Old 05-30-2023, 08:42 AM #3
riceandpho's Avatar
riceandpho riceandpho is offline
Elite Member
 
Join Date: Sep 2005
Location: Oakland CA
Age: 36
Posts: 5,009
riceandpho is a jewel in the rough riceandpho is a jewel in the rough riceandpho is a jewel in the rough
riceandpho riceandpho is offline
Elite Member
riceandpho's Avatar
 
Join Date: Sep 2005
Location: Oakland CA
Age: 36
Posts: 5,009
riceandpho is a jewel in the rough riceandpho is a jewel in the rough riceandpho is a jewel in the rough
i have been using led flasher relay, it replaces the one at the back of the inside fuse box. granted mines not even equipped with DRL, also the only thing youll loose is the flash from factory keyless entry. if you have aftermarket system installed, they should work like normal since its tied to the parking lights.
__________________
Pioneer DEH-80PRS,Rockford Fosgate T600-2,Hertz ML 1650.3(2 pairs),T400-2,Hertz ML 280.3(2 pairs),T1000-1bdcp,(2)JL Audio 12W6v3, Mechman 240a HO Alternator, Dual Northstar 31m,Borla Dual Exhaust,AFE Magnumforce intake.Enkei WT-4 Michelin Defender LTX 275/55R20. retrofitted S2000 projectors,Philips 85122 White Vision,Morimoto 5Five Ballast.Diode Dynamics SS3 Yellow Fog Sport.2 pairs of Hella Supertones.Full led conversion on interior and exterior.HAWK LTS pads F+R, Stoptech slotted rotors and stainless steel lines F+R.Bilstein 5100 @0.85, MOOG FJ Springs front,Bilstein B12 36-281824 rear .
riceandpho is offline   Reply With QuoteReply With Quote
Old 05-30-2023, 09:07 AM #4
Inv4drZm's Avatar
Inv4drZm Inv4drZm is offline
Senior Member
 
Join Date: Sep 2015
Location: Kansas
Age: 28
Posts: 4,275
Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute
Inv4drZm Inv4drZm is offline
Senior Member
Inv4drZm's Avatar
 
Join Date: Sep 2015
Location: Kansas
Age: 28
Posts: 4,275
Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute Inv4drZm has a reputation beyond repute
I had the resistors and I believe they failed, I sanded down the wire in the stock flasher relay thing and its worked great ever since.
__________________
2005 4R Sport 4WD "The last of the V8s!" - Custom TIG'd SS Dual Exhaust - King 2.5" +2 LT. - ARB Front & Rear - 37's - Dana 60 - Build Thread
2005 Tundra 2WD Regular Cab V8 - Chopped Frame - Short Bed Swap
1977 Celica Liftback - LFX Swap - Build Thread
Inv4drZm is offline   Reply With QuoteReply With Quote
Old 05-30-2023, 10:30 PM #5
knightsfs4's Avatar
knightsfs4 knightsfs4 is offline
Member
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
knightsfs4 knightsfs4 is offline
Member
knightsfs4's Avatar
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
Quote:
Originally Posted by riceandpho View Post
i have been using led flasher relay, it replaces the one at the back of the inside fuse box. granted mines not even equipped with DRL, also the only thing youll loose is the flash from factory keyless entry. if you have aftermarket system installed, they should work like normal since its tied to the parking lights.
Do you have a link for the flasher relay you use? I'm honestly torn between using the resistors or getting the flasher relay. I actually have 4 flasher relays from vleds already. I know for the from you can just slap them on, but I am not sure if its the same for the rears. Still trying to figure out the route I wanna take here.
__________________
Knightsfs4 Build Thread http://www.toyota-4runner.org/4th-ge...ld-thread.html
Jack-Purchased on 11/22/10- 2006 Limited 4X4 V8
knightsfs4 is offline   Reply With QuoteReply With Quote
Old 05-30-2023, 11:43 PM #6
xtremewlr's Avatar
xtremewlr xtremewlr is offline
Member
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
xtremewlr xtremewlr is offline
Member
xtremewlr's Avatar
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
I used the Diode Dynamics Smart Tap since I'm running aftermarket LED turn signals in my Coastal front bumper. Plug and play for the most part. I had to get a new OEM short adapter harness for my Limited.

LED Flasher for 2003-2009 Toyota 4Runner (non-DTRL)

You only need this adapter if you have DRLs I believe. With DRLs, the flasher relay is different but this harnes resolves the issue.

__________________
2003 4Runner Limited 4wd V8 - Build thread on Tacoma World
FJ tcase swap, VVT intake swap, Solid Offroad motor mounts, Doug Thorley y-pipe, Bold Performance cat-back, ADS shocks F&R, Metal Tech LTHD springs rear, 1" body lift, 285/75/17 Toyo R/T Trails on Sequoia rims, Coastal front bumper, CAD rear bumper
xtremewlr is offline   Reply With QuoteReply With Quote
Old 05-30-2023, 11:47 PM #7
knightsfs4's Avatar
knightsfs4 knightsfs4 is offline
Member
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
knightsfs4 knightsfs4 is offline
Member
knightsfs4's Avatar
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
Quote:
Originally Posted by xtremewlr View Post
I used the Diode Dynamics Smart Tap since I'm running aftermarket LED turn signals in my Coastal front bumper. Plug and play for the most part. I had to get a new OEM short adapter harness for my Limited.

LED Flasher for 2003-2009 Toyota 4Runner (non-DTRL)

You only need this adapter if you have DRLs I believe. With DRLs, the flasher relay is different but this harnes resolves the issue.

Ok so you are using both the Smart Tap and the harness adapter?

And you are able to run LEDs in the front and back without losing your DRLs?
__________________
Knightsfs4 Build Thread http://www.toyota-4runner.org/4th-ge...ld-thread.html
Jack-Purchased on 11/22/10- 2006 Limited 4X4 V8
knightsfs4 is offline   Reply With QuoteReply With Quote
Old 05-31-2023, 12:52 AM #8
xtremewlr's Avatar
xtremewlr xtremewlr is offline
Member
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
xtremewlr xtremewlr is offline
Member
xtremewlr's Avatar
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
Quote:
Originally Posted by knightsfs4 View Post
Ok so you are using both the Smart Tap and the harness adapter?

And you are able to run LEDs in the front and back without losing your DRLs?
Yes and no.

I had to run the harness to use the smart tap since my truck had DRLs to start. I've disabled the DRLs completely using Techstream. I hate DRL, they are pointless IMO.

I have aftermarket LED turn signals in my aftermarket front bumper. The rear lights are still stock 2003, so don't have LEDs in them.
__________________
2003 4Runner Limited 4wd V8 - Build thread on Tacoma World
FJ tcase swap, VVT intake swap, Solid Offroad motor mounts, Doug Thorley y-pipe, Bold Performance cat-back, ADS shocks F&R, Metal Tech LTHD springs rear, 1" body lift, 285/75/17 Toyo R/T Trails on Sequoia rims, Coastal front bumper, CAD rear bumper
xtremewlr is offline   Reply With QuoteReply With Quote
Old 05-31-2023, 08:52 AM #9
riceandpho's Avatar
riceandpho riceandpho is offline
Elite Member
 
Join Date: Sep 2005
Location: Oakland CA
Age: 36
Posts: 5,009
riceandpho is a jewel in the rough riceandpho is a jewel in the rough riceandpho is a jewel in the rough
riceandpho riceandpho is offline
Elite Member
riceandpho's Avatar
 
Join Date: Sep 2005
Location: Oakland CA
Age: 36
Posts: 5,009
riceandpho is a jewel in the rough riceandpho is a jewel in the rough riceandpho is a jewel in the rough
Quote:
Originally Posted by knightsfs4 View Post
Do you have a link for the flasher relay you use? I'm honestly torn between using the resistors or getting the flasher relay. I actually have 4 flasher relays from vleds already. I know for the from you can just slap them on, but I am not sure if its the same for the rears. Still trying to figure out the route I wanna take here.
i got mines off ebay, didn't even pay over 20 for it.
look for the cf18 flasher, everyone carries a variant of those, as long you dont have DRL, you can use that 8 pin flasher, pretty standard on all toyotas mostly
__________________
Pioneer DEH-80PRS,Rockford Fosgate T600-2,Hertz ML 1650.3(2 pairs),T400-2,Hertz ML 280.3(2 pairs),T1000-1bdcp,(2)JL Audio 12W6v3, Mechman 240a HO Alternator, Dual Northstar 31m,Borla Dual Exhaust,AFE Magnumforce intake.Enkei WT-4 Michelin Defender LTX 275/55R20. retrofitted S2000 projectors,Philips 85122 White Vision,Morimoto 5Five Ballast.Diode Dynamics SS3 Yellow Fog Sport.2 pairs of Hella Supertones.Full led conversion on interior and exterior.HAWK LTS pads F+R, Stoptech slotted rotors and stainless steel lines F+R.Bilstein 5100 @0.85, MOOG FJ Springs front,Bilstein B12 36-281824 rear .
riceandpho is offline   Reply With QuoteReply With Quote
Old 05-31-2023, 12:20 PM #10
xtremewlr's Avatar
xtremewlr xtremewlr is offline
Member
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
xtremewlr xtremewlr is offline
Member
xtremewlr's Avatar
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
Quote:
Originally Posted by riceandpho View Post
i got mines off ebay, didn't even pay over 20 for it.
look for the cf18 flasher, everyone carries a variant of those, as long you dont have DRL, you can use that 8 pin flasher, pretty standard on all toyotas mostly
That's what that adapter cable resolves. Vehicles with DRL have the larger connector, not sure what the pin count is. The adapter harness goes from the larger connector to the non-DRL 8 pin connector.
__________________
2003 4Runner Limited 4wd V8 - Build thread on Tacoma World
FJ tcase swap, VVT intake swap, Solid Offroad motor mounts, Doug Thorley y-pipe, Bold Performance cat-back, ADS shocks F&R, Metal Tech LTHD springs rear, 1" body lift, 285/75/17 Toyo R/T Trails on Sequoia rims, Coastal front bumper, CAD rear bumper
xtremewlr is offline   Reply With QuoteReply With Quote
Old 06-01-2023, 08:42 AM #11
riceandpho's Avatar
riceandpho riceandpho is offline
Elite Member
 
Join Date: Sep 2005
Location: Oakland CA
Age: 36
Posts: 5,009
riceandpho is a jewel in the rough riceandpho is a jewel in the rough riceandpho is a jewel in the rough
riceandpho riceandpho is offline
Elite Member
riceandpho's Avatar
 
Join Date: Sep 2005
Location: Oakland CA
Age: 36
Posts: 5,009
riceandpho is a jewel in the rough riceandpho is a jewel in the rough riceandpho is a jewel in the rough
Quote:
Originally Posted by xtremewlr View Post
That's what that adapter cable resolves. Vehicles with DRL have the larger connector, not sure what the pin count is. The adapter harness goes from the larger connector to the non-DRL 8 pin connector.
the work around for the drl version, is to take a apart the flasher relay, and slowly grind away the resistor bar.

i havent taken apart that harness you talk about, i wonder which wire is tapped together or what extra wire changed.
__________________
Pioneer DEH-80PRS,Rockford Fosgate T600-2,Hertz ML 1650.3(2 pairs),T400-2,Hertz ML 280.3(2 pairs),T1000-1bdcp,(2)JL Audio 12W6v3, Mechman 240a HO Alternator, Dual Northstar 31m,Borla Dual Exhaust,AFE Magnumforce intake.Enkei WT-4 Michelin Defender LTX 275/55R20. retrofitted S2000 projectors,Philips 85122 White Vision,Morimoto 5Five Ballast.Diode Dynamics SS3 Yellow Fog Sport.2 pairs of Hella Supertones.Full led conversion on interior and exterior.HAWK LTS pads F+R, Stoptech slotted rotors and stainless steel lines F+R.Bilstein 5100 @0.85, MOOG FJ Springs front,Bilstein B12 36-281824 rear .
riceandpho is offline   Reply With QuoteReply With Quote
Old 06-01-2023, 09:36 AM #12
xtremewlr's Avatar
xtremewlr xtremewlr is offline
Member
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
xtremewlr xtremewlr is offline
Member
xtremewlr's Avatar
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
Quote:
Originally Posted by riceandpho View Post
the work around for the drl version, is to take a apart the flasher relay, and slowly grind away the resistor bar.

i havent taken apart that harness you talk about, i wonder which wire is tapped together or what extra wire changed.
Why not just do it the right way with the adapter harness? I'd rather do that then a hack job of grinding a resistor. Less chance of issues, especially since it's OEM and only costs $15-$20 from a dealer.
__________________
2003 4Runner Limited 4wd V8 - Build thread on Tacoma World
FJ tcase swap, VVT intake swap, Solid Offroad motor mounts, Doug Thorley y-pipe, Bold Performance cat-back, ADS shocks F&R, Metal Tech LTHD springs rear, 1" body lift, 285/75/17 Toyo R/T Trails on Sequoia rims, Coastal front bumper, CAD rear bumper
xtremewlr is offline   Reply With QuoteReply With Quote
Old 06-01-2023, 06:59 PM #13
knightsfs4's Avatar
knightsfs4 knightsfs4 is offline
Member
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
knightsfs4 knightsfs4 is offline
Member
knightsfs4's Avatar
 
Join Date: Mar 2011
Location: Alpharetta, GA
Posts: 959
knightsfs4 is an unknown quantity at this point
So, if you need the harness for DRL then what is the reasoning for needing the smart tap version?

Wouldn't this along with the harness suffice to fix the hyperflash and still retain DRLs? CF18 ADJUSTABLE FLASHER 8 PIN
__________________
Knightsfs4 Build Thread http://www.toyota-4runner.org/4th-ge...ld-thread.html
Jack-Purchased on 11/22/10- 2006 Limited 4X4 V8

Last edited by knightsfs4; 06-01-2023 at 07:03 PM.
knightsfs4 is offline   Reply With QuoteReply With Quote
Old 06-01-2023, 08:22 PM #14
xtremewlr's Avatar
xtremewlr xtremewlr is offline
Member
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
xtremewlr xtremewlr is offline
Member
xtremewlr's Avatar
 
Join Date: Nov 2019
Location: Tucson, AZ
Posts: 767
Real Name: Todd
xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold xtremewlr is a splendid one to behold
Quote:
Originally Posted by knightsfs4 View Post
So, if you need the harness for DRL then what is the reasoning for needing the smart tap version?

Wouldn't this along with the harness suffice to fix the hyperflash and still retain DRLs? CF18 ADJUSTABLE FLASHER 8 PIN
Because I chose to use the smart tap for the additional features?

You don't need to use the smart tap version, just get whatever works for you to resolve the fast flash. I told you what I used and why the harness was needed.
__________________
2003 4Runner Limited 4wd V8 - Build thread on Tacoma World
FJ tcase swap, VVT intake swap, Solid Offroad motor mounts, Doug Thorley y-pipe, Bold Performance cat-back, ADS shocks F&R, Metal Tech LTHD springs rear, 1" body lift, 285/75/17 Toyo R/T Trails on Sequoia rims, Coastal front bumper, CAD rear bumper
xtremewlr is offline   Reply With QuoteReply With Quote
Old 06-04-2023, 06:37 AM #15
Bluesky 07's Avatar
Bluesky 07 Bluesky 07 is online now
Senior Member
 
Join Date: Sep 2014
Location: Cherokee Co., GA
Posts: 2,691
Real Name: Russell (OB #9908)
Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of
Bluesky 07 Bluesky 07 is online now
Senior Member
Bluesky 07's Avatar
 
Join Date: Sep 2014
Location: Cherokee Co., GA
Posts: 2,691
Real Name: Russell (OB #9908)
Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of Bluesky 07 has much to be proud of
Driverís side resistor placement. Stay as far from the battery as possible since the resistors heat up while operating.

Bluesky 07 is online now   Reply With QuoteReply With Quote
Reply

Tags
flash , issue , leds , signal , turn

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
FS: 5th Gen Lasfit front turn signals. Canbus no Hyperflash no resistor Bayonne Nj 0 skillzo1 For Sale: T4R Items 1 04-05-2020 10:29 AM
Demello LED turn signal and hyperflash- Has anyone solved this issue with a resistor? PAULUNM 4th Gen T4Rs 7 11-05-2014 11:30 PM
Help turn signal mod 2001TR4runner 3rd gen T4Rs 3 09-25-2014 08:51 PM
Turn signal mod ARC 3rd gen T4Rs 10 05-27-2014 03:17 AM
3rd gen turn signal solution... Limbwalker 3rd gen T4Rs 5 09-22-2013 02:30 AM

Powered by vBadvanced CMPS v3.2.2

All times are GMT -4. The time now is 03:03 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2023, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2023 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2023 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2023 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger
 
Copyright © 2020