[4runnerchibcha]

Originally Posted by LFD_Off_Road

The mounting ear got bent during shipping, that happens sometimes. You should be able to bend it back straight. If not then we can swap it out.

Thanks for the reply here. I can probably bend it back, but the bar itself is a tad short, as you can see from pick. I can add some washers, no problem.

However, what do I do with the screws that are tok big?

[toyn280]

Originally Posted by toyn280

Thank you. Will they ship direct or do they go to the vendor I bought them from and then shipped to me? I need to see if I will get them by the 26th or if I need to find another solution for my trip. Thank you for your fast response and help. One of the biggest reason I chose the LFD bars is about the great customer service I read on this forum.


Sent from my iPhone using Tapatalk

Thank you, I live in California. Will you send tracking once you ship? That will help me to see if I need to buy some temporary bars for my trip if I don’t get the ones from LFD in time. Also I had a integrated wind after bar as part of my order, if those are not produced in the same batch you have ready next week, can you ship that separately so at least I can have the bars? Thank you


Sent from my iPhone using Tapatalk

[krhayes79]

@LFD

Any ETA on the fuel tank skid? It is time to get the replacement and I would like to get the matching fuel tank skid to my LFD skid plates.

Thanks!

[LFD_Off_Road]

Originally Posted by krhayes79

@LFD

Any ETA on the fuel tank skid? It is time to get the replacement and I would like to get the matching fuel tank skid to my LFD skid plates.

Thanks!

I just put the latest prototype on my 4R Tuesday. It fit better, but still needs a little bit of tweaking.

[Daikon]

@LFD_Off_Road

Is it possible to order the transmission skid plate for 5th gen? I already have the front AL skid, but would like to get a quote for the transmission skid, since it is not listed on the website by itself.

[Daikon]

Originally Posted by Daikon

@LFD_Off_Road

Is it possible to order the transmission skid plate for 5th gen? I already have the front AL skid, but would like to get a quote for the transmission skid, since it is not listed on the website by itself.

@LFD_Off_Road

[Finslayer83]

[007Tacoma]

Originally Posted by Finslayer83

THAT is just a gorgeous front end.

[Anand]

Originally Posted by Finslayer83

Originally Posted by 007Tacoma

THAT is just a gorgeous front end.

Not sure if @Finslayer83 got the bumper/spot that I originally had, but that is a very very good looking setup!!

[Finslayer83]

I think I was #3 and second of the variants.

With some custom tweaks. I was nagging them for a few months about the project.

Drove over to the shop in February - had it for a few months now.

Day of install at LFD.





This week at the beach





Love it. Strongly recommend #700 coils for the front.

[salsanacho]

For your crossbars, is this type of degradation around the slots normal? It's only been a couple months outside and haven't even installed anything on these cross bars yet.
Crossbar photo

[Sea_ledford]

Anyone know the dimensions of the mounting plate for the air compressor mount?
LFD Off Road - Air Compressor Mount - for ARB Single Compressor


Wondering if I can use it to mount my viair portable compressor.

Thanks!

[007Tacoma]

Originally Posted by Sea_ledford

Anyone know the dimensions of the mounting plate for the air compressor mount?
LFD Off Road - Air Compressor Mount - for ARB Single Compressor


Wondering if I can use it to mount my viair portable compressor.

Thanks!

I had my Viair 300P mounted using the LFD mounting plate under my hood until I got a bigger air box. Now its mounted in the cargo area.

[Sea_ledford]

Originally Posted by 007Tacoma

I had my Viair 300P mounted using the LFD mounting plate under my hood until I got a bigger air box. Now its mounted in the cargo area.

Thanks! I've got a 400P, which looks like is about an inch wider and longer (if I leave the foot plate on). You think it would still fit?

Foot plate dimensions are 10.9" x 5.8"

[007Tacoma]

Originally Posted by Sea_ledford

Thanks! I've got a 400P, which looks like is about an inch wider and longer (if I leave the foot plate on). You think it would still fit?

Foot plate dimensions are 10.9" x 5.8"

I took the foot plate off. I reused the isolators to keep the vibrations to a minimum, and that worked really well. Honestly, the LFD Plate is Stainless Steel - so, if the hole don't line up you can still drill new holes without worrying about rust. Its definitely worth it. I can't use mine anymore, but I'm keeping it in case I can repurpose it - so many ideas floating around...