User Tag List

Reply
 
Thread Tools Rate Thread Display Modes
Old 12-18-2020, 09:37 PM #1
4runner_dreamer's Avatar
4runner_dreamer 4runner_dreamer is offline
Member
 
Join Date: Nov 2015
Location: Stevens Point, WI
Posts: 117
Real Name: Nate
4runner_dreamer is on a distinguished road
4runner_dreamer 4runner_dreamer is offline
Member
4runner_dreamer's Avatar
 
Join Date: Nov 2015
Location: Stevens Point, WI
Posts: 117
Real Name: Nate
4runner_dreamer is on a distinguished road
LCA Replacement??

Hey team...

After searching this thread, I am in need of a bit more advice/opinions about lower control arm replacing and product choice.

My 2011 has seen better days when it comes to rust (like many of us on here) and the cam bolts on the controls arms have become part of the vehicle - there's no moving them; torched them and all..

With that being said, I want to replace them and put either new bushings OR lower control arm assemblies (both sides).

However, I'm kinda leaning towards replacing the whole assembly My thought is there's less labor due to having to clean out the bushing housings and not f*ck them up..

I've found a couple different options as far as arms, but, the brand names are throwing me off..

Here's the links:
Security Check
Amazon.com: Dorman 526-653 Front Driver Side Lower Suspension Control Arm and Ball Joint Assembly for Select Toyota Models: Automotive

Side note: I do medium-type overlanding and need something of quality..

I guess what I'm looking for from you is your honest opinion on what route you'd take. Whole arms? Just bushings? Best cam bolts? Beer?

Regards.
__________________
2011 4Runner SR5 - 5100's - ICON 3" Rear - 285/70 AT3's - 17" AR - Morimoto Mini H1 Retrofit - Amsoil - K&N Drop In - WT Mats -
SOLD - 2000 4Runner Limited - Midnight Black - E-Locker - Amsoil - Custom Magnaflow Muffler - B5100's - OME 891 - Diff Drop - K&N CAI - 265/75R16 KO2's - 4X-Innovations Front - Tundra Brakes

"Faith and fear both demand that you believe in something you cannot see. It's your choice."#BobProctor
4runner_dreamer is offline   Reply With QuoteReply With Quote
Old 12-18-2020, 10:43 PM #2
Nobody Special's Avatar
Nobody Special Nobody Special is offline
Member
 
Join Date: Dec 2020
Location: Nowhere Special
Posts: 676
Real Name: Special Ed
Nobody Special is a jewel in the rough Nobody Special is a jewel in the rough Nobody Special is a jewel in the rough
Nobody Special Nobody Special is offline
Member
Nobody Special's Avatar
 
Join Date: Dec 2020
Location: Nowhere Special
Posts: 676
Real Name: Special Ed
Nobody Special is a jewel in the rough Nobody Special is a jewel in the rough Nobody Special is a jewel in the rough
Most "brands" are just that. Brands = labels/stickers on a box. Very few manufacturers make their own stuff.
Order parts from somewhere, slap their label on the box, then sell at a markup.

Go on RockAuto.
Take some part numbers, all of them, and enter them on the net and see all the different brands that pop up for that part number.


See how there are multiple part numbers for the same part?
2011 TOYOTA 4RUNNER 4.0L V6 Control Arm | RockAuto

Now, if there is a 10 digit/letter part number, put a dash ( - ) in between the first five and last five as well.
Interesting how that all works.
But the dashed number is how Toyota does it.

Last edited by Nobody Special; 12-18-2020 at 10:49 PM.
Nobody Special is offline   Reply With QuoteReply With Quote
Old 12-18-2020, 10:44 PM #3
LandCruiser's Avatar
LandCruiser LandCruiser is offline
Senior Member
 
Join Date: Feb 2013
Location: East Bay
Posts: 4,584
Real Name: Sparky
LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of
LandCruiser LandCruiser is offline
Senior Member
LandCruiser's Avatar
 
Join Date: Feb 2013
Location: East Bay
Posts: 4,584
Real Name: Sparky
LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of LandCruiser has much to be proud of
I would replace the entire LCA assembly with OEM stuff. That’s what I did. They tend to rust to shit, and yours is just old enough to experience those symptoms.
__________________
Old and (c)rusty.
LandCruiser is offline   Reply With QuoteReply With Quote
Old 12-18-2020, 10:47 PM #4
RedSled's Avatar
RedSled RedSled is offline
Senior Member
 
Join Date: Feb 2014
Posts: 2,016
RedSled has a spectacular aura about RedSled has a spectacular aura about
RedSled RedSled is offline
Senior Member
RedSled's Avatar
 
Join Date: Feb 2014
Posts: 2,016
RedSled has a spectacular aura about RedSled has a spectacular aura about
Don’t know if this helps you or not.

Total Chaos makes a replacement LCA for Toyota 4Runners. I think they also make an extended travel, longer LCA that widens the front track. It's a more involved process to widen the track and involves other handling issues, according to posts I've read here by others who have done it.
TOTAL CHAOS FABRICATION
__________________
2015 T4R Trail Edition w/KDSS. Baja Rack flat utility rack, Baja Rack ladder, WeatherTech floor mats, Demello rock sliders. RCI skid plates, Falken AT3W LT285/70R17 tires, ICON Stage 7 tubular 2" extended travel lift, ICON Rebound 17x8.5" 0 offset alloy wheels, Baxter Performance remote oil filter adapter. Side exit exhaust, 2nd recovery hook on rear frame corner, DIY wheel well liners with 1/4" neoprene rubber.
__________________
2017 Silver SR5 Premium
Vietnam 67-68

Greed and corruption are rampant.
RedSled is offline   Reply With QuoteReply With Quote
Old 12-18-2020, 11:27 PM #5
Jeremy556's Avatar
Jeremy556 Jeremy556 is offline
Senior Member
 
Join Date: Jan 2012
Location: Fruita, CO
Age: 43
Posts: 3,985
Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold
Jeremy556 Jeremy556 is offline
Senior Member
Jeremy556's Avatar
 
Join Date: Jan 2012
Location: Fruita, CO
Age: 43
Posts: 3,985
Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold
I recently replaced my LCAs because one of the bushings broke. OEM arms are just over $300 each and lasted me over 250k miles, so I went OEM.

Have seen several posts on this forum of people that got aftermarket arms, bushings, or ball joints that ended up not fitting because mfgs assumed that the LCAs were the same from 4th to 5th gen. Perhaps those have been worked out by now
Jeremy556 is offline   Reply With QuoteReply With Quote
Old 12-18-2020, 11:33 PM #6
4runner_dreamer's Avatar
4runner_dreamer 4runner_dreamer is offline
Member
 
Join Date: Nov 2015
Location: Stevens Point, WI
Posts: 117
Real Name: Nate
4runner_dreamer is on a distinguished road
4runner_dreamer 4runner_dreamer is offline
Member
4runner_dreamer's Avatar
 
Join Date: Nov 2015
Location: Stevens Point, WI
Posts: 117
Real Name: Nate
4runner_dreamer is on a distinguished road
What about the cam bolts?

I noticed moog ones (I believe) come greaseable...

Amazon.com: Moog K100129 Caster/Camber Adjusting Kit: Automotive

or even these from Metal Tech:
Toyota Alignment Cam Bolts | Camber Bolt Kit | Metal Tech 4x4
__________________
2011 4Runner SR5 - 5100's - ICON 3" Rear - 285/70 AT3's - 17" AR - Morimoto Mini H1 Retrofit - Amsoil - K&N Drop In - WT Mats -
SOLD - 2000 4Runner Limited - Midnight Black - E-Locker - Amsoil - Custom Magnaflow Muffler - B5100's - OME 891 - Diff Drop - K&N CAI - 265/75R16 KO2's - 4X-Innovations Front - Tundra Brakes

"Faith and fear both demand that you believe in something you cannot see. It's your choice."#BobProctor
4runner_dreamer is offline   Reply With QuoteReply With Quote
Old 12-18-2020, 11:34 PM #7
4runner_dreamer's Avatar
4runner_dreamer 4runner_dreamer is offline
Member
 
Join Date: Nov 2015
Location: Stevens Point, WI
Posts: 117
Real Name: Nate
4runner_dreamer is on a distinguished road
4runner_dreamer 4runner_dreamer is offline
Member
4runner_dreamer's Avatar
 
Join Date: Nov 2015
Location: Stevens Point, WI
Posts: 117
Real Name: Nate
4runner_dreamer is on a distinguished road
Quote:
Originally Posted by LandCruiser View Post
I would replace the entire LCA assembly with OEM stuff. That’s what I did. They tend to rust to shit, and yours is just old enough to experience those symptoms.
That's fair..
__________________
2011 4Runner SR5 - 5100's - ICON 3" Rear - 285/70 AT3's - 17" AR - Morimoto Mini H1 Retrofit - Amsoil - K&N Drop In - WT Mats -
SOLD - 2000 4Runner Limited - Midnight Black - E-Locker - Amsoil - Custom Magnaflow Muffler - B5100's - OME 891 - Diff Drop - K&N CAI - 265/75R16 KO2's - 4X-Innovations Front - Tundra Brakes

"Faith and fear both demand that you believe in something you cannot see. It's your choice."#BobProctor
4runner_dreamer is offline   Reply With QuoteReply With Quote
Old 12-18-2020, 11:37 PM #8
PK930's Avatar
PK930 PK930 is offline
Member
 
Join Date: Apr 2016
Location: Houston'ish
Posts: 173
PK930 will become famous soon enough
PK930 PK930 is offline
Member
PK930's Avatar
 
Join Date: Apr 2016
Location: Houston'ish
Posts: 173
PK930 will become famous soon enough
My lower BJs were shot and so were the bushings.

I replaced them with Dirt Kings and couldn't be happier. I got them for a good deal otherwise I would have just stuck with OEM.

If its really rusted and bad, just cut off the cam bolts to free arms for removal. Then get new cam bolts and use anti-seize.
__________________
Something, something, something.
PK930 is offline   Reply With QuoteReply With Quote
Old 12-19-2020, 12:59 AM #9
Jeremy556's Avatar
Jeremy556 Jeremy556 is offline
Senior Member
 
Join Date: Jan 2012
Location: Fruita, CO
Age: 43
Posts: 3,985
Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold
Jeremy556 Jeremy556 is offline
Senior Member
Jeremy556's Avatar
 
Join Date: Jan 2012
Location: Fruita, CO
Age: 43
Posts: 3,985
Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold Jeremy556 is a splendid one to behold
I don't think greasable bolt gains you much, other than the cheaper purchase price versus OEM. I pulled my OEM bolts a few months after purchase and coated them with brake grease, still had to cut the arms out with a sawzall, and I live in the desert. The bushings seize to the mounting tabs on the frame.
Jeremy556 is offline   Reply With QuoteReply With Quote
Old 12-19-2020, 10:32 AM #10
85GT-79FJ40 85GT-79FJ40 is offline
Member
 
Join Date: Nov 2018
Location: NH
Posts: 229
85GT-79FJ40 will become famous soon enough
85GT-79FJ40 85GT-79FJ40 is offline
Member
 
Join Date: Nov 2018
Location: NH
Posts: 229
85GT-79FJ40 will become famous soon enough
Mine has 80k on it and the ball joints are fine. But the factory bushings are mush even when new. And you can find Sankei 555 ball joints (OE supplier) on ebay if you look hard enough. I put Whiteline polyurethane LCA bushings in mine. I'm a classic car restoration tech by trade and I will say the job sucked. Took me 7 hours WITH the truck on a lift and a full shop of tools. It's very difficult to get the old bushings out because they press in from the outside and you have to press them out from the inside. Of all the tools and equipment I had on hand the stock jack was what I wound up using to push out the bushing cores. Then lots of careful air chisel use to get the sleeves out without messing up the arms. But it was well worth it. The front end feels SO much better. more precise steering, no more jiggling steering wheel on washboard roads... It is definitely transmitting more road feel into the vehicle which I don't mind.

I'll also say those greasable MOOG cam bolts... Don't bother. They aren't the correct size. I bought those and it was a complete waste of money. I had to cut out one of the factory bolts and had no choice but to use one of those to get the truck off the lift but wound up getting a dealer replacement the following monday. So I couldn't return them as one is used.

From the research I did a lot of the aftermarket replacement arms listed don't actually fit 5th gens either. And Whiteline doesn't list the bushings I bought for a 4Runner. But after some research I discovered that the second generation of FJ Cruiser from I think 09 uses the same arms as a 5th gen and that's what I bought the bushings for. They fit perfect.
__________________
Toyota 4x4 #17 - 2011 4Runner Trail Edition
85GT-79FJ40 is offline   Reply With QuoteReply With Quote
Old 12-19-2020, 11:02 AM #11
delloro's Avatar
delloro delloro is offline
Senior Member
 
Join Date: Apr 2015
Location: I. E. So. Cal
Posts: 1,162
delloro is just really nice delloro is just really nice delloro is just really nice delloro is just really nice
delloro delloro is offline
Senior Member
delloro's Avatar
 
Join Date: Apr 2015
Location: I. E. So. Cal
Posts: 1,162
delloro is just really nice delloro is just really nice delloro is just really nice delloro is just really nice
Quote:
Originally Posted by 85GT-79FJ40 View Post
Mine has 80k on it and the ball joints are fine. But the factory bushings are mush even when new. And you can find Sankei 555 ball joints (OE supplier) on ebay if you look hard enough. I put Whiteline polyurethane LCA bushings in mine. I'm a classic car restoration tech by trade and I will say the job sucked. Took me 7 hours WITH the truck on a lift and a full shop of tools. It's very difficult to get the old bushings out because they press in from the outside and you have to press them out from the inside. Of all the tools and equipment I had on hand the stock jack was what I wound up using to push out the bushing cores. Then lots of careful air chisel use to get the sleeves out without messing up the arms. But it was well worth it. The front end feels SO much better. more precise steering, no more jiggling steering wheel on washboard roads... It is definitely transmitting more road feel into the vehicle which I don't mind.

I'll also say those greasable MOOG cam bolts... Don't bother. They aren't the correct size. I bought those and it was a complete waste of money. I had to cut out one of the factory bolts and had no choice but to use one of those to get the truck off the lift but wound up getting a dealer replacement the following monday. So I couldn't return them as one is used.

From the research I did a lot of the aftermarket replacement arms listed don't actually fit 5th gens either. And Whiteline doesn't list the bushings I bought for a 4Runner. But after some research I discovered that the second generation of FJ Cruiser from I think 09 uses the same arms as a 5th gen and that's what I bought the bushings for. They fit perfect.
Do the Whiteline bushings squeak, or have a provision to grease them?
delloro is offline   Reply With QuoteReply With Quote
Old 12-19-2020, 12:25 PM #12
85GT-79FJ40 85GT-79FJ40 is offline
Member
 
Join Date: Nov 2018
Location: NH
Posts: 229
85GT-79FJ40 will become famous soon enough
85GT-79FJ40 85GT-79FJ40 is offline
Member
 
Join Date: Nov 2018
Location: NH
Posts: 229
85GT-79FJ40 will become famous soon enough
Quote:
Originally Posted by delloro View Post
Do the Whiteline bushings squeak, or have a provision to grease them?
Not a peep yet and it's been about 1k miles. They come with grease to lube the centers where the inner sleeves go through and you can lube the ends too which I did. And there are formed washers to cap the ends of the sleeves. I feel there's very little chance they will squeak. Of course I put urethane sway bar bushings in the truck front and rear over 40k miles ago and haven't heard a peep from those either. It would be nice if the LCA's had fittings like my JBA uppers but I doubt it'll be an issue. I used a generous amount of anti-seize on all the adjustment bolts too.
__________________
Toyota 4x4 #17 - 2011 4Runner Trail Edition
85GT-79FJ40 is offline   Reply With QuoteReply With Quote
Old 12-19-2020, 02:37 PM #13
BackOff's Avatar
BackOff BackOff is offline
Senior Member
 
Join Date: Dec 2012
Location: Earth, Central Oregun
Age: 53
Posts: 1,196
Real Name: Derek
BackOff is a jewel in the rough BackOff is a jewel in the rough BackOff is a jewel in the rough BackOff is a jewel in the rough
BackOff BackOff is offline
Senior Member
BackOff's Avatar
 
Join Date: Dec 2012
Location: Earth, Central Oregun
Age: 53
Posts: 1,196
Real Name: Derek
BackOff is a jewel in the rough BackOff is a jewel in the rough BackOff is a jewel in the rough BackOff is a jewel in the rough
Quote:
Originally Posted by 85GT-79FJ40 View Post
Mine has 80k on it and the ball joints are fine. But the factory bushings are mush even when new. And you can find Sankei 555 ball joints (OE supplier) on ebay if you look hard enough. I put Whiteline polyurethane LCA bushings in mine. I'm a classic car restoration tech by trade and I will say the job sucked. Took me 7 hours WITH the truck on a lift and a full shop of tools. It's very difficult to get the old bushings out because they press in from the outside and you have to press them out from the inside. Of all the tools and equipment I had on hand the stock jack was what I wound up using to push out the bushing cores. Then lots of careful air chisel use to get the sleeves out without messing up the arms. But it was well worth it. The front end feels SO much better. more precise steering, no more jiggling steering wheel on washboard roads... It is definitely transmitting more road feel into the vehicle which I don't mind.

I'll also say those greasable MOOG cam bolts... Don't bother. They aren't the correct size. I bought those and it was a complete waste of money. I had to cut out one of the factory bolts and had no choice but to use one of those to get the truck off the lift but wound up getting a dealer replacement the following monday. So I couldn't return them as one is used.

From the research I did a lot of the aftermarket replacement arms listed don't actually fit 5th gens either. And Whiteline doesn't list the bushings I bought for a 4Runner. But after some research I discovered that the second generation of FJ Cruiser from I think 09 uses the same arms as a 5th gen and that's what I bought the bushings for. They fit perfect.

I discovered if you cut the flange off the outside bushing sleeve you can press out the bushings easier... now that your done ...not much help.
__________________
2004 T4R 4x4 SR5 v6
Some modifications.
Black-N-Blue
BackOff is offline   Reply With QuoteReply With Quote
Old 12-19-2020, 04:26 PM #14
85GT-79FJ40 85GT-79FJ40 is offline
Member
 
Join Date: Nov 2018
Location: NH
Posts: 229
85GT-79FJ40 will become famous soon enough
85GT-79FJ40 85GT-79FJ40 is offline
Member
 
Join Date: Nov 2018
Location: NH
Posts: 229
85GT-79FJ40 will become famous soon enough
Quote:
Originally Posted by BackOff View Post
I discovered if you cut the flange off the outside bushing sleeve you can press out the bushings easier... now that your done ...not much help.
That was actually my plan. Tried it on the first one and after fighting it for over 2 hours I pushed them out the correct way. Which turned out to be much quicker. For me at least. I'm sure if my truck was from a no-salt use area it would have taken much less time overall.
__________________
Toyota 4x4 #17 - 2011 4Runner Trail Edition
85GT-79FJ40 is offline   Reply With QuoteReply With Quote
Old 12-21-2020, 03:56 PM #15
TotalAutomotiveLV TotalAutomotiveLV is offline
Senior Member
 
Join Date: Feb 2015
Location: Las Vegas, NV
Posts: 3,026
TotalAutomotiveLV has a spectacular aura about TotalAutomotiveLV has a spectacular aura about TotalAutomotiveLV has a spectacular aura about
TotalAutomotiveLV TotalAutomotiveLV is offline
Senior Member
 
Join Date: Feb 2015
Location: Las Vegas, NV
Posts: 3,026
TotalAutomotiveLV has a spectacular aura about TotalAutomotiveLV has a spectacular aura about TotalAutomotiveLV has a spectacular aura about
If you are looking for Aftermarket LCA's, Dirt King has been
the most popular for us over the last year.

Part #DK-814704




Features:

- CAD designed
- Slanted front plate to deflect objects
- Internally ribbed with extrusions for weight reduction
- Preassembled for fast installation
- Grease fitting ports for easy servicing
- Zinc plated components for corrosion resistance
- Bump stop plating
- Limit strap tabbing
- Professionally MIG welded
- Proudly made in the USA

_
TotalAutomotiveLV is offline   Reply With QuoteReply With Quote
Reply

Tags
arm , arms , control , lower , replacing

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Auto Trans Shifter Bushing Replacement & Transfer Case Shifter Seat Replacement mtbtim 3rd gen T4Rs 17 09-14-2022 08:23 PM
Lower Ball Joint replacement or dust boot replacement help? dot_tom 5th gen T4Rs 7 01-11-2018 11:52 PM
xreas replacement - shock vs shock/spring replacement amheck 4th Gen T4Rs 21 11-14-2017 08:21 PM
3rd Gen 4runner Rear Coil Spring Replacement and Rear Shock Bushing Replacement mtbtim 3rd gen T4Rs 7 11-28-2016 11:43 AM
CV boot replacement vs entire joint replacement zerowkul98 Maintenance/Detailing 3 06-29-2010 06:30 PM

Powered by vBadvanced CMPS v3.2.2

All times are GMT -4. The time now is 09:17 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger
 
Copyright © 2020