06-26-2021, 10:32 PM
|
#1
|
|
Member
|
|
Join Date: Jun 2021
Location: KY
Posts: 115
|
|
Member
Join Date: Jun 2021
Location: KY
Posts: 115
|
Trouble Installing Morimoto HID Bulb in Factory Projector
I'm having trouble installing an HID bulb in the driver's side projector and am looking for some advice/help.
I bought a plug n play kit from TRS. I've used a few of their kits in other cars and have always been pleased. Tonight I tried installing the bulb in the driver's side projector and couldn't seem to get the bulb in far enough to be able to turn it. I took that bulb to the passenger side and it was tight but I was able to get it installed.
I went back to the driver's side with the factory bulb and it installs easily. I took the other HID bulb and attempted to install it again. I got the bulb in and was able to just barely turn it to where it didn't just fall back out but was unable to turn it any further by hand. I took a pair of pliers (I know, I know) and attempted to turn the bulb, and it did turn some. I don't believe it got completely turned when 2 of the lugs snapped off the bulb.
I've ordered another set of bulbs from TRS but I REALLY don't want the same thing to happen with the new ones! I know I shouldn't use pliers but I couldn't see another way of turning it. Any advice for me, beside don't use pliers?
|
|
Reply With Quote
|
06-26-2021, 10:54 PM
|
#2
|
|
Senior Member
|
|
Join Date: Dec 2013
Location: Near Baton Rouge, LA
Age: 70
Posts: 4,062
|
|
Senior Member
Join Date: Dec 2013
Location: Near Baton Rouge, LA
Age: 70
Posts: 4,062
|
Quote:
Originally Posted by Frasher4Runner
I'm having trouble installing an HID bulb in the driver's side projector and am looking for some advice/help.
I bought a plug n play kit from TRS. I've used a few of their kits in other cars and have always been pleased. Tonight I tried installing the bulb in the driver's side projector and couldn't seem to get the bulb in far enough to be able to turn it. I took that bulb to the passenger side and it was tight but I was able to get it installed.
I went back to the driver's side with the factory bulb and it installs easily. I took the other HID bulb and attempted to install it again. I got the bulb in and was able to just barely turn it to where it didn't just fall back out but was unable to turn it any further by hand. I took a pair of pliers (I know, I know) and attempted to turn the bulb, and it did turn some. I don't believe it got completely turned when 2 of the lugs snapped off the bulb.
I've ordered another set of bulbs from TRS but I REALLY don't want the same thing to happen with the new ones! I know I shouldn't use pliers but I couldn't see another way of turning it. Any advice for me, beside don't use pliers?
|
Did you try to swap the one that was installed in the passenger side? Did it go in without issue?
Try when the new bulbs come in. If you still have the same issue, loosen the small screws on the back side of the reflector housing where the bulbs go in until you can place the bulbs in with friction. It may take you a couple of tries.....
Let us know how it goes!
__________________
Best Regards,
Saker
2021 T4R *MIDNIGHT BLACK METALLIC* TRD OFF ROAD PREMIUM 4X4| Saker’s Ebony Build | Saker’s Previous 2014 Midnight Build | Scuba Mod | LED LIGHT BAR INSTALL | Saker's EBRs Photos Updated 05-21-16| Saker's Previous 2013 FJ TT/SE
|
|
Reply With Quote
|
06-26-2021, 11:11 PM
|
#3
|
|
Member
|
|
Join Date: Jun 2021
Location: KY
Posts: 115
|
|
Member
Join Date: Jun 2021
Location: KY
Posts: 115
|
Trouble Installing Morimoto HID Bulb in Factory Projector
Quote:
Originally Posted by Saker
Did you try to swap the one that was installed in the passenger side? Did it go in without issue?
Try when the new bulbs come in. If you still have the same issue, loosen the small screws on the back side of the reflector housing where the bulbs go in until you can place the bulbs in with friction. It may take you a couple of tries.....
Let us know how it goes!
|
The bulb that I put in the passenger side I had initially tried to put in the driver side, but had the same issue - couldn’t seem to push it in far enough to be able to turn it.
You mention reflector housing - would that be the same for the projectors? (I have the Limited model)
Sent from my iPhone using Tapatalk Pro
|
|
Reply With Quote
|
06-27-2021, 12:57 AM
|
#4
|
|
Member
|
|
Join Date: May 2018
Location: GA
Posts: 400
|
|
Member
Join Date: May 2018
Location: GA
Posts: 400
|
try to play with the o-rings on the hid bulb base. swap the stocks o rings in or take the o rings out to see if its easier to turn...
|
|
Reply With Quote
|
06-27-2021, 01:03 PM
|
#5
|
|
Senior Member
|
|
Join Date: Dec 2013
Location: Near Baton Rouge, LA
Age: 70
Posts: 4,062
|
|
Senior Member
Join Date: Dec 2013
Location: Near Baton Rouge, LA
Age: 70
Posts: 4,062
|
Quote:
Originally Posted by Frasher4Runner
The bulb that I put in the passenger side I had initially tried to put in the driver side, but had the same issue - couldn’t seem to push it in far enough to be able to turn it.
You mention reflector housing - would that be the same for the projectors? (I have the Limited model)
|
Now that I think about it, you may not be able to get to the projector housing...
so my solution will probably not work, sorry!
But, try
@ Axix23
suggestion. that may work for you!
__________________
Best Regards,
Saker
2021 T4R *MIDNIGHT BLACK METALLIC* TRD OFF ROAD PREMIUM 4X4| Saker’s Ebony Build | Saker’s Previous 2014 Midnight Build | Scuba Mod | LED LIGHT BAR INSTALL | Saker's EBRs Photos Updated 05-21-16| Saker's Previous 2013 FJ TT/SE
|
|
Reply With Quote
|
06-27-2021, 01:12 PM
|
#6
|
|
Member
|
|
Join Date: May 2018
Location: GA
Posts: 400
|
|
Member
Join Date: May 2018
Location: GA
Posts: 400
|
^^ I had the same issue when the o rings were brand new. But afferwards, they were more loose to turn. I want to say the Oem h11 bulb o rings were more thick. Without the o rings, it was super loose to turn into the headlight.
|
|
Reply With Quote
|
06-27-2021, 01:27 PM
|
#7
|
|
Member
|
|
Join Date: Jun 2012
Location: Pleasure Point, Ca
Posts: 210
Real Name: Natey
|
|
Member
Join Date: Jun 2012
Location: Pleasure Point, Ca
Posts: 210
Real Name: Natey
|
You lost me at "play with your 0-Ring".
__________________
2012 Limited...Stock
|
|
Reply With Quote
|
06-27-2021, 04:42 PM
|
#8
|
|
Junior Member
|
|
Join Date: Jun 2021
Location: Los Angeles
Posts: 28
|
|
Junior Member
Join Date: Jun 2021
Location: Los Angeles
Posts: 28
|
Make sure an o ring didn't also accidentally get stuck on the housing. I've seen that happen.
I would swap your stock o rings to the aftermarket bulb.
I just did all my lights and found the oem o rings to be much better and perfect size.
Good luck
Sent from my Pixel 4 XL using Tapatalk
Last edited by Filthy4Runner63; 06-28-2021 at 03:12 AM.
|
|
Reply With Quote
|
06-27-2021, 09:59 PM
|
#9
|
|
Member
|
|
Join Date: Jun 2021
Location: KY
Posts: 115
|
|
Member
Join Date: Jun 2021
Location: KY
Posts: 115
|
If I do remove the battery to make more room, what am I looking at in terms of needing codes or the like for the stereo to work? Anything?
Sent from my iPhone using Tapatalk Pro
|
|
Reply With Quote
|
06-28-2021, 03:11 AM
|
#10
|
|
Junior Member
|
|
Join Date: Jun 2021
Location: Los Angeles
Posts: 28
|
|
Junior Member
Join Date: Jun 2021
Location: Los Angeles
Posts: 28
|
Quote:
Originally Posted by Frasher4Runner
If I do remove the battery to make more room, what am I looking at in terms of needing codes or the like for the stereo to work? Anything?
Sent from my iPhone using Tapatalk Pro
|
Shouldn't pop any codes, radio will probably clear memory stuff. You can also plug in a memory saver to your 12v cig lighter so when you unplug the battery it's like nothing happened. It is a tight little spot I cut up my hands a bit when I just did My headlight. Make sure you check the tabs too the bulbs I got had the biggest tab a little to large I grinded it a tad with a Dremel and was able to finally get it in. I didn't suggest this before because you mentioned you could fit it in the passenger side
Sent from my Pixel 4 XL using Tapatalk
|
|
Reply With Quote
|
06-29-2021, 12:27 PM
|
#11
|
|
Elite Member
|
|
Join Date: Mar 2010
Location: Pittsburgh
Posts: 5,688
Real Name: Chris
|
|
Elite Member
Join Date: Mar 2010
Location: Pittsburgh
Posts: 5,688
Real Name: Chris
|
I had this issue with my Morimoto HID kit and had to have them send me the other h11 bulbs because I could not get them to seat right
__________________
2017 Nautical Blue SR5 Premium - Black Emblems, AFE 76mm TB, AFE Momentum GT Intake, URD MAF Calibrator, Borla Touring Cat-Back Exhaust, VR ECU Tune, RCI Skid Plate, Morimoto MLED 2.0 Headlight Retrofit, Morimoto LED Fogs, Eagle Eye Smoked Black Tail Lights, FyreFlys LED Interior, Meso Puddle Lights, Tinted Mirror Turn Signals, Smoked Amber Raptor Lights, Odyssey 34 Battery, 32" LED Bar with Rago Hidden Brackets, Rago Molle Panels, Side Shooter LED Ditch Lights, sPod w/ PowerTray, Raceline Matte Bronze Wheels w/ Cooper Discoverer RTX, CaliRaised Rock Sliders, BajaRack Full Length Roof Rack, Kenwood DMX1057XR, Infinity Kappa Door Speakers and 3.5's in dash, JL 8w3v3 in JBL Enclosure, Husky Weather Beaters, Blackvue DR900S Dash Cams
|
|
Reply With Quote
|
06-29-2021, 01:56 PM
|
#12
|
|
Member
|
|
Join Date: Jun 2021
Location: KY
Posts: 115
|
|
Member
Join Date: Jun 2021
Location: KY
Posts: 115
|
I got my new bulbs in today; had them sent next day air since I currently only have 1 working headlight. I'll try to tackle the installation again tonight. I'll swap out the o-ring from an OEM bulb first and if I can't get that in easily I'll remove the battery. I don't think I've ever had this much trouble installing one of these kits.
|
|
Reply With Quote
|
06-29-2021, 08:49 PM
|
#13
|
|
Member
|
|
Join Date: May 2019
Location: Chicago's NW Suburbs
Posts: 232
|
|
Member
Join Date: May 2019
Location: Chicago's NW Suburbs
Posts: 232
|
I reused the OEM o-rings on mine, went in nice and snug after that.
__________________
RCI Sliders & TRD Integration, Transmission and Transfer Case Skids
Eibach TRD Pro Lift, 285/70/17 KO2s
TRD Intake, ARB Breathers
Pioneer 8500NEX
|
|
Reply With Quote
|
06-29-2021, 11:01 PM
|
#14
|
|
Member
|
|
Join Date: Jun 2021
Location: KY
Posts: 115
|
|
Member
Join Date: Jun 2021
Location: KY
Posts: 115
|
Success! I figured out what I was doing wrong and once I fixed it, it went right in. The bulbs are shipped with a plastic cap contraption over them to protect them. It’s a 3 part system that screws together. Once you remove the cap you have to put the o-ring into place before installation - I wasn’t getting it in the right spot. Once I realized that I took the passenger side out and fixed it too.
Sent from my iPhone using Tapatalk Pro
|
|
Reply With Quote
|
07-04-2021, 01:52 PM
|
#15
|
|
Junior Member
|
|
Join Date: Jun 2021
Location: Los Angeles
Posts: 28
|
|
Junior Member
Join Date: Jun 2021
Location: Los Angeles
Posts: 28
|
Quote:
Originally Posted by Frasher4Runner
Success! I figured out what I was doing wrong and once I fixed it, it went right in. The bulbs are shipped with a plastic cap contraption over them to protect them. It’s a 3 part system that screws together. Once you remove the cap you have to put the o-ring into place before installation - I wasn’t getting it in the right spot. Once I realized that I took the passenger side out and fixed it too.
Sent from my iPhone using Tapatalk Pro
|
Oh yeah you gotta make sure it seats on that very bottom portion cause it does seem like it belongs right above it, didn't even consider that. Glad you got it fixed!
Sent from my Pixel 4 XL using Tapatalk
|
|
Reply With Quote
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
|