User Tag List

Reply
 
Thread Tools Rate Thread Display Modes
Old 12-10-2016, 08:07 PM #1
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB

Hey everyone, here are the install instructions for our new 14+ 4runner Lo-Pro winch bumper.

Tools required:
-10mm wrench/socket
-12mm wrench/socket
-14mm wrench/socket
-19mm wrench/socket
-9/16" wrench/socket
-1/2" wrench/socket
-Small flathead screwdriver
-Large flathead screwdriver
-Die grinder or airsaw to use for cutting plastic bumper.


First off the plastic bumper cover needs to be removed from the vehicle.
Start by opening the hood and removing the plastic clips that hold the radiator shroud cover in place. Use the small flathead screwdriver to pop the center of the clip up, and then pull the clip out of the hole. Completely remove the cover and set it aside with the clips.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3975-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3976-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3978-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com

Last edited by C4 Fabrication; 03-04-2018 at 08:52 PM.
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-10-2016, 08:11 PM #2
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Now remove the plastic clips and screws with 10mm head that attach the bumper cover to the steel radiator support.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3979-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3981-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3982-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-10-2016, 08:16 PM #3
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Then remove all of the small screws with 10mm head that hold the plastic fender liner to the bumper cover. Note where the screws go so you can put them back into the same locations. Some screws are different lengths and diameters than others.
Also fully remove the small black plastic cover that goes from the bottom of the plastic bumper cover to the frame of the vehicle.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3985-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3988-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3990-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3991-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3992-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-10-2016, 08:22 PM #4
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Now disconnect the fog light wiring harness from the light and then the bumper cover will be ready to remove.

Start at one corner of the bumper cover where it meets the fender. Firmly pull out and forward on the plastic to remove it from the clips that hold it in place.
Follow the same procedure on the other side of the vehicle and the bumper cover will come right off in one big piece.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3995-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3994-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3998-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn3999-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4000-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4001-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-10-2016, 08:27 PM #5
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
The aluminum crash bar can now be removed from the frame of the 4runner.
Use a 14mm socket to remove the nuts holding the crash bar on, then remove the crash bar mounting brackets from the frame as well.
Be sure to save the bolts that hold the crash bar brackets to the frame, these will be re-used to hold the new Lo-Pro bumper in place.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4016-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4018-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4019-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-10-2016, 08:31 PM #6
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Next we are going to start on the bumper cover cutting process.
First remove the silver plastic trim cover from the front lower area of the bumper cover. Use a flat head screwdriver to pop the plastic clips out of the back side of the cover.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4002-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4003-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4004-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-10-2016, 08:40 PM #7
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Now the bumper can be marked for cutting. Use masking tape to create an easy line to follow when cutting. Basically the cut is made right along the deepest part of the groove where the silver plastic cover used to meet the edge of the bumper cover. Also lay out a line right above the slotted holes below the lower grille mesh area. The slotted holes are where the silver plastic cover used to fit through the bumper cover.

When cutting the left and right side, be sure to cut right in the center of the deep grooved area on each side. This will ensure good fitment to the new Lo-Pro bumper. The area that needs to be cut along the slotted holes doesnt have to be a perfect smooth straight line. This area will get covered by the new Lo-Pro bumper.

Any rough edges along the cut can be cleaned up with a sanding pad on a die grinder or with a knife and file.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4005-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4007-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4006-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4010-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4008-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4011-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4012-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4013-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-10-2016, 08:53 PM #8
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
The plastic bumper cover can now be installed back onto the 4runner using the original hardware. We have discovered that it is actually much easier to install the Lo-Pro onto the 4runner first, before the plastic bumper cover is installed. The light bar and winch can be installed into the Lo-Pro, then the Lo-Pro can be installed onto the 4runner, then the plastic bumper cover can go on after that.
The aluminum crash bar and brackets along with the small plastic skid plate DO NOT get installed back onto the 4runner.

Push firmly on the corners of the bumper cover to clip it back onto the fender area. Make sure to plug in the wiring harness for the fog lights before re-attaching the plastic fender liner to the bottom of the bumper cover.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4022-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4023-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4024-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com

Last edited by C4 Fabrication; 03-04-2018 at 08:55 PM.
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-11-2016, 02:12 PM #9
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Now that the plastic bumper cover has been re-installed, a couple other things need to be done before the Lo-Pro bumper can be installed.

You will need to trim off some plastic from the air dam on the driver side so the bumper upright support can fit without interference. Cut off a portion that resembles the shape in the picture. You may need to test fit the bumper real quick to make sure you have trimmed enough.

Next if you are installing a winch into your Lo-Pro bumper, you will need to slightly bend the A/C condenser line to make room for the body of the winch.
In the photos you can see where the winch would interfere with the line if it is not adjusted out of the way.
When adjusting the line, carefully and slowly bend the line a little bit at a time in a slight arc to create a gradual bend. This will prevent the line from kinking when it is adjusted. Also support the line where it attaches to the condenser to make sure the line does not crack loose from the fitting.

MAKE SURE TO CHECK ALL CLEARANCES BETWEEN THE BUMPER, WINCH AND A/C LINE BEFORE THE FINAL INSTALL! If the A/C line is rubbing on the winch or the bumper somewhere, it can puncture the line and allow the Freon to leak out.
It is also a good precaution to add a piece of rubber hose around the A/C line in any areas where rubbing may occur.


Also some winches may interfere with the small metal grille support bracket right in the center area in front of the condenser. This bracket can be slightly bent back with a mallet or crescent wrench to create the necessary clearance.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4025-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4028-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4031-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4033-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4038-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com

Last edited by C4 Fabrication; 07-25-2017 at 02:21 PM.
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-11-2016, 02:19 PM #10
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Now it is time to install the Lo-Pro bumper onto the 4runner.
If you are installing a winch and/or LED light into the bumper, do it now before the bumper is installed onto the 4runner.

If you are installing an Extreme LED 30" Pro series 2D light bar into the bumper, you will need to use the two small "L" shaped tabs provided in the Lo-Pro hardware kit to install the light. Do not use the tabs that come with the light, they will be too tall. Install the "L" tabs onto the light with the longer leg attaching to the light and the shorter leg mounting to the tabs that are welded into the bumper.
There is a photo of the mounting tabs at the bottom of this post. There is also a photo of one of the tabs mounted to the light inside a bumper as well.


Once your bumper accessories are installed, you can lift the bumper into place on the vehicle. Have a friend get one bolt on each side at the top of the frame mount threaded in enough to hold the bumper in place. Then the rest of the bolts can loosely be installed. Use the provided grade eight 3/8" flat washers with the factory bolts when installing the bumper.

Adjust the bumper up or down on the slotted holes to align it with the plastic bumper cover as desired.

The remaining bolts can now be tightened down.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4276-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4279-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4692-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4708-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com

Last edited by C4 Fabrication; 10-25-2017 at 09:02 PM.
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-11-2016, 02:25 PM #11
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Now install the extra frame support brackets on the back of the bumper which attach to the sides of the frame rail.
There is a left and right hand bracket, make sure you use the correct one on each side, they should only fit one way.

Loosely attach the bracket to the back of the bumper with the provided 3/8" carriage head bolt. Then thread the provided M12 bolt into the side of the frame rail. Use the provided 1/2" flat washer on the bolt as well. Adjust the bracket so it sits flat on both surfaces and tighten down the bolts.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4280-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4282-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4285-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4286-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 12-11-2016, 02:32 PM #12
C4 Fabrication's Avatar
C4 Fabrication C4 Fabrication is offline
Senior Member
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
C4 Fabrication C4 Fabrication is offline
Senior Member
C4 Fabrication's Avatar
 
Join Date: Sep 2015
Location: Black Hills of South Dakota
Age: 33
Posts: 1,185
Real Name: Caleb
C4 Fabrication has a spectacular aura about C4 Fabrication has a spectacular aura about
Lastly you will need to install the flat brackets that attach the original plastic bumper cover to the bottom edge of the Lo-Pro bumper.
The flat bracket goes on the inside of the Lo-Pro and plastic bumper.
Set the bracket into position and install the 3/8" carriage head bolt up through the bottom corner of the Lo-Pro bumper and through the flat bracket. Loosely install the washers and nut.
Now install the provided 5/16" bolt through the hole in the plastic bumper up through the flat bracket. Install the washers and nut and tighten everything down.

Your Lo-Pro bumper installation is now complete! Finish wiring the winch and light, and you are ready to hit the trail.

Thank you for purchasing your Lo-Pro winch bumper from C4 FAB!
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4287-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4291-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4294-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4296-jpg  14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-dscn4298-jpg 
__________________


Owner/Operator of C4 Fabrication. specializing in custom built Toyota off-road products.www.c4fabrication.com
C4 Fabrication is offline   Reply With QuoteReply With Quote
Old 05-27-2018, 11:05 PM #13
ProShooter1 ProShooter1 is offline
Junior Member
 
Join Date: Jan 2018
Location: Canton, GA
Posts: 1
ProShooter1 is on a distinguished road
ProShooter1 ProShooter1 is offline
Junior Member
 
Join Date: Jan 2018
Location: Canton, GA
Posts: 1
ProShooter1 is on a distinguished road
Power Steering Line

Iím In the middle of installing the C4 Lo Pro bumper and the power steering line is in the way of the winch control box. Anyone experienced this? It isnít a line that is easily bent like the AC line. I wish I had known this would be a possibility before I took a Dremel to my brand new truck. It does not fit cleanly across the top of the box like what I have pictured in the attachment.
Attached Images
14+ 4runner Lo-Pro Winch Bumper install instructions by C4 FAB-1f458cb2-bf0d-4fd5-b21a-9e74e4f9b594-jpg 
ProShooter1 is offline   Reply With QuoteReply With Quote
Old 04-16-2019, 10:54 PM #14
kkruel55 kkruel55 is offline
Junior Member
 
Join Date: Oct 2018
Location: Denver, CO
Posts: 18
kkruel55 is on a distinguished road
kkruel55 kkruel55 is offline
Junior Member
 
Join Date: Oct 2018
Location: Denver, CO
Posts: 18
kkruel55 is on a distinguished road
I really like this bumper, but I have a couple questions:

Does it come powder coated? Can it come powder coated?

What is a good time estimate for a reputable shop to install it?
kkruel55 is offline   Reply With QuoteReply With Quote
Old 05-21-2019, 08:11 PM #15
T4R_KAI's Avatar
T4R_KAI T4R_KAI is offline
Member
 
Join Date: Nov 2018
Location: San Diego, CA
Posts: 112
Real Name: Josh
T4R_KAI will become famous soon enough
MY GARAGE
T4R_KAI T4R_KAI is offline
Member
T4R_KAI's Avatar
 
Join Date: Nov 2018
Location: San Diego, CA
Posts: 112
Real Name: Josh
T4R_KAI will become famous soon enough
MY GARAGE
Quote:
Originally Posted by kkruel55 View Post
I really like this bumper, but I have a couple questions:

Does it come powder coated? Can it come powder coated?

What is a good time estimate for a reputable shop to install it?
2014+ 4Runner Lo Pro Winch Bumper | C4 Fabrication
__________________
2017 TRD Off-Road -- Dobinsons 3/2 Lift w/ Camburg UCAs, Method 701s, Falken Wildpeaks AT3W, Xenon HID Low / LED High, Cali Raised LED, N-Fab Nerfs, Pro Grill

On Order:
SSO Roof Rack
T4R_KAI is offline   Reply With QuoteReply With Quote
Reply

Tags
bumper , hybrid , led light bar , plate bumper , winch bumper

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Factory Bumper Winch Install stickw 4th Gen T4Rs 24 01-21-2018 11:55 PM
Anyone install their winch after installing their ARB bumper? Derek G 4th Gen T4Rs 1 12-03-2013 11:34 PM
BudBuilt Winch Plate Install Instructions? RyanC 5th gen T4Rs 27 12-11-2011 01:34 PM
Winch install w/o aftermarket bumper thetaxguy Off-Roading 17 08-25-2009 06:12 PM

Powered by vBadvanced CMPS v3.2.2

All times are GMT -4. The time now is 01:21 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger
 
Copyright © 2019


Garage Plus vBulletin Plugins by Drive Thru Online, Inc.