Dropzone's 1994 4Runner Expedition/Overland Build - Page 29 - Toyota 4Runner Forum

thespwilson · 04-04-2020, 09:38 AM

Quote:

Originally Posted by Dropzone

I haven't been really active on this forum since my long term project has been an 81 Toyota Trekker:

The truck is highly capable: 5.29's, dual cases, full caged.
It has been fun for the last 8 years but it is just getting beat to death. Frame is about shot. I am kind of tired of the whole beat the truck in the rocks phase.

I have been thinking about another truck/4runner as a replacement. SOmething that can act as a capable weekend warrior/semi daily driver.

So a few days ago look what the Dodge dragged home

Picked up my neice's 1994 4runner with 195k on it.
Recent rebuild on the 3.turd so it actually runs decents, dog slow with the Auto.
I got it dirt cheap, low 3 digit numbers due to a failed bearing/CV on the right front wheel that lead to this

Totally froze on her and freaked her out. Her mom said come get it.

It is kind of dirty but should clean up nicely

Has the usual drivers side torn seat but other than that nothing sometime with a vacuum and carpet cleaner can't cure

Plan is to tear apart the right front and see what got fubar'ed.
It needs tires, an exhaust and the left rear passenger window won't roll down.

Long term plan is to turn it into a more family friendly trail runner, won't have the same capabilities as the Trekker but time will tell. Looking to build something I can take the grandkids out to enjoy the woods in and maybe the occasional 2-3 night weekend expedition.

It will get some front (with a winch) and rear bumpers, probably an extra gas tank, drawer unit/sleeping platform. Maybe something like an ARB fridge.
Definitely a locker, sliders.
Thinking 33x10.50's for tires.

Build will be a slow one

great looking rig!

Dropzone · 04-04-2020, 10:01 PM

Got bored and decided to see if I could form some diamond plate to fit the curve of a door.
For years I have liked diamond plate on the lower part of a door.
Busted out an extra door to use as a form, a rubber mallet and some clamps. Pound the aluminum and than cut to fit.
It actually fit the curve of the 2nd gen door pretty good.
I used some 1/4" thick aluminum stock to act as sort of a door slider for idiots in the parking lot. Borrowed the door slider idea from @Dirtco
.
.
I'll need to strip the aluminum later on since I got a little impatient and didn't wait long enough for the paint to dry.

Dropzone · 04-12-2020, 12:23 AM

Got a late start working on the totally unnecessary diamond plate on the 4runner door project today.
Ended up taking the driver's side door off. And of course forgot there is 3 plugs on the door harness instead of 2 so had to fix a couple of wires I accidentally stripped.
I took vacation tomorrow from work so hopefully I can get this door back on and at least one other door done.

Dropzone · 04-12-2020, 10:09 PM

Day 3 of the #covid19projects that is totally unnecessary but keeps my mind off the BS of the world.
Tried to pull the passenger side harness from the firewall but looked like I would have to pull more of the dash than I wanted.
So plan B was to pull the door harness out of the door.
Gonna be a pain to re-install but oh well.
The diamond plate I had left over was a bit thicker than the stuff I used for the driver's side so had to use a bigger hammer and a piece of old railing. Beat it into submission and it seemed to fit the curve of the door nicely.
I almost wish I had left it polished, looks good..if i hadn't #monsterliner this thing i probably would have left it.
The missus suggested painting the door slider black. Actually sort of like it so I may hit the other two doors with it.
I only work 2 days this week so will hopefully have this thing wrapped up

Dropzone · 04-16-2020, 08:33 PM

Got the front doors hung and the wiring harnesses back in.
on the passenger side back door I decided to see how it would go forming the aluminum with the door still on the truck. It was a pain in the ass but actually went faster..
Not perfect but I like the way it came out.
Door sliders should offer great protection from people in the parking garage at work. It was one of those fun see if I can do it sort of projects to keep my mind off the BS of the world.
I am truly blessed to have a cool wife that let's me have a ton of garage time

Dropzone · 04-19-2020, 09:00 AM

found an older side shot so did a comparison.
other than some of the black bleeding through i like how it came out. I will probably order some more desert tan monstaliner down the road to do the rockers

Jlpskydive · 04-19-2020, 09:22 AM

Looks great!

Dropzone · 04-26-2020, 10:05 PM

Swapped grills this morning, trimmed it a bit tighter around the winch solenoid box

Got the 81 Trekker's grill emblem in a better spot

Also had a pile left over 8020 so Decided to give building a drawer unit a shot.
2 drawers, will end up being 16"x6" x 38" deep.
It will be low enough to still get Kenai's crate on top of it and still have head room for sleeping in the back.
I think I will have enough material left to extend it for a sleeping platform with storage underneath.

Dropzone · 04-27-2020, 10:27 PM

Got one drawer built and all the stuff cut for the other drawer.
I went with a non traditional drawer slide, trying out an overhead track idea. No clue if it will work or not.

4Reak Show · 04-27-2020, 11:12 PM

That's awesome. Curious how it will all turn out. I'm still on the fence for a drawer system in mine... The tailgate is sort of a gift and a curse all at once.

Dropzone · 04-29-2020, 10:16 PM

Got the BS covid19 drawer distraction project put together and installed. Need to paint and slap some carpet on top. Ended up taller than I wanted but overall happy with it.
2 drawers, inside dimensions 6 × 16 x 37"