10-10-2016, 01:51 PM
|
#16
|
 |
Member
|
|
Join Date: May 2015
Location: Forest Falls, CA
Posts: 272
|
|
|
Member
Join Date: May 2015
Location: Forest Falls, CA
Posts: 272
|
Quote:
Originally Posted by 4Reak Show
My 95 4WD auto looked like the top pic before conversion, if that helps.
On another note, I'd kill for a set for 2nd gen 4WD Manual. Grey is best, any chance you'd do black? Thanks and good luck
|
I have a color match for the Tan but have not found a color match for the gray. If I can't find a gray color match then I will offer Tan and black. The 4WD manual trans cup holder is all done and a large batch already made. I will have pics of it installed tomorrow. Should be up on my website some time next week. I just need to wrap up the 4x4 auto double cup holder.
__________________
4Runner cup holders
|
|
 Reply With Quote
|
|
10-10-2016, 01:58 PM
|
#17
|
|
Member
|
|
Join Date: May 2015
Location: Forest Falls, CA
Posts: 272
|
|
|
Member
Join Date: May 2015
Location: Forest Falls, CA
Posts: 272
|
For those that don't go back a page here is my previous post. I need to know what year 2nd Gen the 2nd console (bottom pic) is from. My old 92 had the 1st console and from the earlier post a 95 had the same console so I'm very confused on where this console is from. So I was trying to wrap up the double cup holder design for the 4x4 automatic console and came across some conflicting imagery. I need some help here. I'm seeing two different consoles for the 4x4 automatic for the 2nd Gen 4Runner. What years are the two consoles below from? I have been working off of the 1st one but realized there may be two versions I need.
__________________
4Runner cup holders
|
|
|
Reply With Quote
|
|
10-10-2016, 04:12 PM
|
#18
|
|
Member
|
|
Join Date: May 2015
Location: Forest Falls, CA
Posts: 272
|
|
|
Member
Join Date: May 2015
Location: Forest Falls, CA
Posts: 272
|
Maybe I should just ask a more specific question. Does anyone on this forum have the console in the 2nd pic above? If so, what year is it?
__________________
4Runner cup holders
|
|
|
Reply With Quote
|
|
10-10-2016, 06:01 PM
|
#19
|
 |
Senior Member
|
|
Join Date: Nov 2013
Location: Elsewhere
Posts: 1,686
|
|
|
Senior Member
Join Date: Nov 2013
Location: Elsewhere
Posts: 1,686
|
Quote:
Originally Posted by bhicks22
Maybe I should just ask a more specific question. Does anyone on this forum have the console in the 2nd pic above? If so, what year is it?
|
Pretty sure the bottom picture is out of a Toyota Surf (probably the philipines), though most are right hand drive...
__________________
1994 4Runner AKA: Project Recycle
@503dropzone on IG
Last edited by Dropzone; 10-10-2016 at 06:04 PM.
|
|
|
Reply With Quote
|
|
10-10-2016, 07:48 PM
|
#20
|
|
Member
|
|
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
Member
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
Quote:
Originally Posted by Dropzone
Pretty sure the bottom picture is out of a Toyota Surf (probably the philipines), though most are right hand drive...
|
Ok. I will just stick with the console that I have and hope that it covers all the US spec Auto 4x4 2nd Gens out there.
|
|
|
Reply With Quote
|
|
10-10-2016, 11:30 PM
|
#21
|
|
Member
|
|
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
Member
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
So I'm working on the double cup design for the 4x4 auto right now and need some help. I need a top view of the console and a profile side view of the console from the passenger side looking towards the drive side. There are a couple dimensions I'm needing and I can just add my notes of where I need dimensions from if I have those to pics to draw on.
|
|
|
Reply With Quote
|
|
10-11-2016, 11:11 PM
|
#22
|
|
Member
|
|
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
Member
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
Alright Socal guys. I need access to a 4X4 auto. I have a prototype that just came off the machine. It fits on the center console piece I have BUT I don't know how it will fit up against the plastic shifter housing that has the P-N-D-etc. I want to make sure it clears that plastic hump. Anyone in the IE that would give me 5 minutes with their 2nd Gen?
|
|
|
Reply With Quote
|
|
10-12-2016, 01:36 PM
|
#23
|
|
Junior Member
|
|
Join Date: Sep 2011
Location: Tacoma, WA
Posts: 11
|
|
|
Junior Member
Join Date: Sep 2011
Location: Tacoma, WA
Posts: 11
|
Can't help with the auto but just went to your page and don't see the manual ones there. I'll buy one when they are.
Thanks.
|
|
|
Reply With Quote
|
|
10-12-2016, 02:15 PM
|
#24
|
|
Member
|
|
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
Member
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
Quote:
Originally Posted by odonekanobe
Can't help with the auto but just went to your page and don't see the manual ones there. I'll buy one when they are.
Thanks.
|
I have the manual double and the 2WD auto double done and in stock but not on my website. I want to have the 4WD auto done and available when I release them. I have a prototype in my hands and ready to test fit but just need the 4Runner to test fit on.
Last edited by bhicks; 10-12-2016 at 02:57 PM.
|
|
|
Reply With Quote
|
|
10-12-2016, 06:38 PM
|
#25
|
 |
Member
|
|
Join Date: Jan 2011
Location: Virginia Beach, Va.
Posts: 60
|
|
|
Member
Join Date: Jan 2011
Location: Virginia Beach, Va.
Posts: 60
|
Quote:
Originally Posted by bhicks
It's possible. I have about a 1/2 dozen different Toyota grey colors in stock. Hopefully one will match. All 3 consoles I have used for mockup were the tan color. I should be able to track down a gray one at my local pick a part this week.
|
Thanks for the reply. My console is a gray color. It looks like your 1 st photo of 2 different consoles.
Also I sent a photo to your e-mail, titled: 2nd gen console color.
Thanks for making a product for over 20 yr old vehicle.
__________________
92, V-6, AT, 31x10.50, 4.88, Leather interior, purchased:1/24/11 with 192,194 miles. New Toyota dealer installed timing belt, timing belt pulley, water pump, T-stat, acc. belts: 12/6/11, 202,475 miles. 242,xxx miles as of 12/08/14. 252,xxx miles as of 08/22/15. 282,xxx miles as of 2/12/18.
KYB Monomax Performance Gas Shocks 565058-front
KYB Monomax Performance Gas Shocks 565059-rear
Moog CC255 Variable Rate Rear Springs
Last edited by astynx; 10-12-2016 at 06:48 PM.
|
|
|
Reply With Quote
|
|
10-13-2016, 07:01 PM
|
#26
|
|
Member
|
|
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
Member
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
|
Reply With Quote
|
|
10-14-2016, 12:47 PM
|
#27
|
|
Member
|
|
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
Member
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
I'm at the point where I'm almost ready to beg. I BADLY need access to a 4WD auto 2nd Gen in Socal. Somebody has to be somewhat local to me with one. I have a prototype done and ready for install. I can't move and make and the final fitment changes until I get it fitted.
Last edited by bhicks; 10-14-2016 at 12:50 PM.
|
|
|
Reply With Quote
|
|
10-15-2016, 09:51 AM
|
#28
|
 |
Senior Member
|
|
Join Date: Jul 2015
Location: Northern California
Age: 37
Posts: 1,471
|
|
|
Senior Member
Join Date: Jul 2015
Location: Northern California
Age: 37
Posts: 1,471
|
Quote:
Originally Posted by bhicks
I'm at the point where I'm almost ready to beg. I BADLY need access to a 4WD auto 2nd Gen in Socal. Somebody has to be somewhat local to me with one. I have a prototype done and ready for install. I can't move and make and the final fitment changes until I get it fitted.
|
I have a customer up here in Napa/BayArea with a 4x4 auto but I don't know if you'd ship it and how useful I'd be for final fitment... And that's a long drive for you just to test fit. If that's an option I'm willing to help.
Other idea would be to head to a pick n pull. The Row 52 App shows when cars arrive and if you can find a fresh, unmolested interior that could work. Just talk to them about your project and they should let you bring in a cupholder. Most guys here are rather laid back. (It's a f*ckin junkyard for goodness sake).
Good luck and we're all excited for you progress.
__________________
The 4Reak Show: 1995 4Runner, 3.4 swapped, manual conversion, supercharged & 7th injected, Eaton TrueTrac in rear, poly bushings F&R, lots of other outrageous add ons...
Wife's: 2016 Trail Premium, bone stock until she joins T4R.org one day...
|
|
|
Reply With Quote
|
|
10-15-2016, 07:35 PM
|
#29
|
|
Member
|
|
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
|
|
Member
Join Date: Dec 2012
Location: Forest Falls, CA
Posts: 180
|
I am going to look at a 2nd Gen craigslist ad that is close to me. Promised the seller I would help him sell it by posting info on it here in return for giving me access to his interior for a few minutes. Should have some test fit pics and needed measurements soon.
|
|
|
Reply With Quote
|
|
10-15-2016, 07:59 PM
|
#30
|
 |
Senior Member
|
|
Join Date: Jul 2012
Location: Imperial County, CA
Posts: 2,354
Real Name: Jeff
|
|
|
Senior Member
Join Date: Jul 2012
Location: Imperial County, CA
Posts: 2,354
Real Name: Jeff
|
Wow. Sorry your having such a hard time trying to find an auto console. I think there is one in the junkyard by my work. If you still need it on Monday I could probably swing by.
If anyone is thinking about sending bhicks a console and worrying about not getting it back, I can say my dealings with him have been superb! Great quality products (that I love!) and great service. I can't recommend this guy or his products enough.
__________________
97 SR5 4runner: 2" OME Lift, rear E-Locker, 231mm Tundra Brakes, 203K, B&M 70264 Tranny Cooler, Duratracs
Build
|
|
|
Reply With Quote
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
|
Linear Mode
