User Tag List

Reply
 
Thread Tools Rating: Thread Rating: 16 votes, 4.94 average. Display Modes
Old 03-17-2009, 10:27 PM #1
snowbizx snowbizx is offline
Member
 
Join Date: Dec 2008
Location: Chicago
Age: 40
Posts: 46
snowbizx is on a distinguished road
snowbizx snowbizx is offline
Member
 
Join Date: Dec 2008
Location: Chicago
Age: 40
Posts: 46
snowbizx is on a distinguished road
Changing Differential & Transfer Case Fluids - Pics Included

A few pics and a quick write-up to help the first timers (like me!) out there. Please excuse the cell phone pictures.

Tools needed:

- 12mm & 24mm socket
- 10mm hex bit socket
- Ratchet/Breaker bar (torque wrench recommended)
- 3"+ extender
- 7 qts. gear lube
- Bottle pump
- Drain pan

Part numbers for crush washers and fill/drain plugs (thanks @aika1 and @d_clark ):

Transfer Case Fill Gasket 90430-18008
Transfer Case Drain Gasket 90430-18008
Front Differential Fill Gasket 12157-10010
Front Differential Drain Gasket 90430-24003
Rear Differential Fill Gasket 12157-10010
Rear Differential Drain Gasket 12157-10010

Transfer Case Drain Plug 90341-18006
Transfer Case Fill Plug 90341-18006
Transfer Case Breather Plug 90930-03172
Rear Differential Drain Plug 90341-18057
Rear Differential Fill Plug 90341-18006
Rear Differential Breather Plug 90930-03031
Front Differential Drain Plug 90341-24014
Front Differential Fill Plug 90341-18032
Front Differential Breather Plug 90930-03136
Oil Pan Drain Plug 90341-12012
Oil Pan Drain Plug Gasket 90430-12031

For some extra room to work, I put my truck on a couple of ramp stands. I used a level on the side steps to find where the truck sits on even ground. Then I tried to find a spot on my driveway so that the car was level when it was on the ramps. Luckily, I found the perfect spot and I got working:



It looks uneven but it's really level, I promise

I started in the front and removed the 4 skid plate bolts. To get the the front 2 bolts, use an extension since they're recessed a few inches.

NOTE: It is a good rule of thumb to remove the fill bolt before the drain. If this does not come off, then STOP! and at least you're not stranded in your garage without any gear lube in your car...

First I drained and filled the front diff:



Drain Plug - 10mm hex bit, 48 ft/lbs
Fill Plug - 10mm hex bit, 29 ft/lbs
Fill quantity - 1.5 qts.


Next was the transfer case:



Drain Plug - 24mm socket, 27 ft/lbs
Fill Plug - 24mm socket, 27 ft/lbs
Fill quantity - 1.5 qts.


And last, I turned the car around (after reinstalling the skid plate) to do the rear diff:



Drain Plug - 24mm socket, 36 ft/lbs
Fill Plug - 24mm socket, 36 ft/lbs
Fill quantity - 3+ qts. (6.3 pints)


I just made sure that I filled each one up the fill plug to the point where gear lube started to drip out. Toyota spec is 0-5mm from the fill holes.

I only had 5k miles on the truck at the time, but I wanted to make the switch to synthetic... I used Amsoil 75W-90 in all three. Also, I heard it's not a bad idea to switch out the factory fill bc most of the break-in for the differentials is within the first 3500-5000 miles anyway.

Here's the metal that was on the rear's drain plug:



As you might expect, the transfer case gear lube was basically still new. The front and rear had minor discoloration. Also, don't forget the magnetic plugs are the drain plugs!

Time to start towing! Good luck everyone

Last edited by snowbizx; 08-02-2014 at 12:46 PM.
snowbizx is offline   Reply With QuoteReply With Quote
Old 03-17-2009, 11:39 PM #2
KB084RUNNER KB084RUNNER is offline
Member
 
Join Date: Mar 2009
Location: Ohio
Posts: 459
KB084RUNNER is on a distinguished road
KB084RUNNER KB084RUNNER is offline
Member
 
Join Date: Mar 2009
Location: Ohio
Posts: 459
KB084RUNNER is on a distinguished road
Great post! Since I will be doing the same soon I appreciate it. I got the Amsoil 80w90 for the rear because that is what is in the book. I'll use mobil1 75w90 or Valvoline Syn 75w90 for the other two.
KB084RUNNER is offline   Reply With QuoteReply With Quote
Old 03-18-2009, 12:58 AM #3
snowbizx snowbizx is offline
Member
 
Join Date: Dec 2008
Location: Chicago
Age: 40
Posts: 46
snowbizx is on a distinguished road
snowbizx snowbizx is offline
Member
 
Join Date: Dec 2008
Location: Chicago
Age: 40
Posts: 46
snowbizx is on a distinguished road
[QUOTE]Originally posted by AMSOIL
[B]AMSOIL Severe Gear
snowbizx is offline   Reply With QuoteReply With Quote
Old 03-18-2009, 06:30 AM #4
kn38ms's Avatar
kn38ms kn38ms is offline
Member
 
Join Date: Dec 2007
Location: Texas Hill Country
Posts: 164
kn38ms is on a distinguished road
kn38ms kn38ms is offline
Member
kn38ms's Avatar
 
Join Date: Dec 2007
Location: Texas Hill Country
Posts: 164
kn38ms is on a distinguished road
I removed the spare when I drained my rear diff.
LOTS of room when removed.
Also its a good time to clean the rim and inspect etc...
__________________
07' Sport
4WD
4.7L
18.7 mpg

Awesome!
kn38ms is offline   Reply With QuoteReply With Quote
Old 03-18-2009, 03:47 PM #5
The Wanderer The Wanderer is offline
Member
 
Join Date: Apr 2006
Location: anywhere
Posts: 84
The Wanderer is on a distinguished road
The Wanderer The Wanderer is offline
Member
 
Join Date: Apr 2006
Location: anywhere
Posts: 84
The Wanderer is on a distinguished road
Looks good

I will be doing the same this summer. I currently have 35000 miles on her and the extra info will help. Probably going with Mobil 1.
__________________
2005 Limited V8 Galactic Gray
The Wanderer is offline   Reply With QuoteReply With Quote
Old 03-18-2009, 07:56 PM #6
CJ3Flyr's Avatar
CJ3Flyr CJ3Flyr is offline
Super Moderator
 
Join Date: Jan 2008
Location: Metro ATL & Cape Coral, FL
Age: 59
Posts: 6,276
CJ3Flyr will become famous soon enough
CJ3Flyr CJ3Flyr is offline
Super Moderator
CJ3Flyr's Avatar
 
Join Date: Jan 2008
Location: Metro ATL & Cape Coral, FL
Age: 59
Posts: 6,276
CJ3Flyr will become famous soon enough
Thumbs up

Great post, thanks I placed a link to it in a few other threads that are related



I don't want to contribute to a population explosion of stickies. If someone reads through the transmission servicing or the greasing driveshaft sticky they'll find a link to this if they want it.

This is another thread with more discussion: http://www.toyota-4runner.org/showth...threadid=10117


CJ3Flyr is offline   Reply With QuoteReply With Quote
Old 03-18-2009, 08:22 PM #7
J.A.'s Avatar
J.A. J.A. is offline
Senior Member
 
Join Date: Jul 2007
Location: NY
Posts: 1,472
J.A. will become famous soon enough J.A. will become famous soon enough
J.A. J.A. is offline
Senior Member
J.A.'s Avatar
 
Join Date: Jul 2007
Location: NY
Posts: 1,472
J.A. will become famous soon enough J.A. will become famous soon enough
Keep in mind that the Fill and Drain plug crush gaskets are Toyota specified as a "Non-reusable part".
J.A. is offline   Reply With QuoteReply With Quote
Old 03-25-2009, 01:39 AM #8
etom's Avatar
etom etom is offline
Member
 
Join Date: Sep 2005
Location: San Francisco
Age: 46
Posts: 100
etom is an unknown quantity at this point
etom etom is offline
Member
etom's Avatar
 
Join Date: Sep 2005
Location: San Francisco
Age: 46
Posts: 100
etom is an unknown quantity at this point
Anyone in need of a couple of quarts of Amsoil 75w-90 Severe Gear oil? I just changed my diffs. and transfer case and have 2 unopened quarts left over (bought extra because I mixed up quarts w/pints ). I paid $12.75 each and can do $20 shipped for both.
__________________
2005 Limited Titanium w/Stone V8 4WD NAV
TRD dual cat-back exhaust, TRD Pro Wheels (Matte Gray), K&N intake (63-9029) w/amsoil dry filter, Amsoil fluids, 265/70/17 Toyo Open Country AT III, Bilstein 5100 @ .85", Sprint Booster V3
etom is offline   Reply With QuoteReply With Quote
Old 04-22-2009, 04:05 PM #9
mudbelly mudbelly is offline
Junior Member
 
Join Date: Feb 2009
Location: DFW, TX
Posts: 12
mudbelly is an unknown quantity at this point
mudbelly mudbelly is offline
Junior Member
 
Join Date: Feb 2009
Location: DFW, TX
Posts: 12
mudbelly is an unknown quantity at this point
Quote:
Originally posted by kn38ms
I removed the spare when I drained my rear diff.
LOTS of room when removed.
Also its a good time to clean the rim and inspect etc...
Werd on that - I just did this today after reading this. Taking out the spare made plenty of room, and I found some pretty deep "rubs" in the sidewall of the spare (2 years in same spot); I would suggest rotating the spare tire on its holder every few months (looks like I need to replace this one).

I used Royal Purple 75/90 in the diff. Just drain out old, clean bolts, squirt in new. I must say that this task is even easier than changing the engine oil. Just fiddy bones for some sweet synth punkin' juice...
__________________
2006 4.0L Sport Edition, Galactic Grey Mica, RWD, Spoiler, Roof, Stock

2008 Maxima SL
mudbelly is offline   Reply With QuoteReply With Quote
Old 04-24-2009, 07:03 PM #10
Border411's Avatar
Border411 Border411 is offline
Member
 
Join Date: Sep 2004
Location: Fairfax, VA
Posts: 696
Border411 is on a distinguished road
Border411 Border411 is offline
Member
Border411's Avatar
 
Join Date: Sep 2004
Location: Fairfax, VA
Posts: 696
Border411 is on a distinguished road
PLEASE REMEMBER THESE TORQUE SPECS!

Just to fill in the gaps, the torque on the front diff should be:

Drain:48ft/lbs
Fill:29ft/lbs

Rear Diff:
Drain and Fill:36ft/lbs

This is per the Toyota Repair Manual.
__________________
Shaun
2004 Titanium Silver Toyota 4Runner SR5 V6 4WD
265/70-17 LTX M/S, Bilstein 5100's Front (1 3/4" lift), DDM 35W HID 3000K Fogs, Silverstar High Beams, GE Nighthawk Low Beams, Showoff Krypton Hyper White Interior Bulbs, EGR Hood Protector, De-Badged, Husky Floor Liners (F/R), 3M Cabin Filter Mod, Fram SureDrain, Side Exhaust, Scion 1807 H/U
Border411 is offline   Reply With QuoteReply With Quote
Old 05-15-2009, 12:11 PM #11
fishrod's Avatar
fishrod fishrod is offline
Member
 
Join Date: Nov 2008
Location: Kelowna, BC
Posts: 269
fishrod is on a distinguished road
fishrod fishrod is offline
Member
fishrod's Avatar
 
Join Date: Nov 2008
Location: Kelowna, BC
Posts: 269
fishrod is on a distinguished road
Quote:
Originally posted by J.A.
Keep in mind that the Fill and Drain plug crush gaskets are Toyota specified as a "Non-reusable part".
What does this mean? The seals on the plugs need to be replaced when you remove them?
fishrod is offline   Reply With QuoteReply With Quote
Old 05-15-2009, 03:57 PM #12
G.I.G.'s Avatar
G.I.G. G.I.G. is offline
Senior Member
 
Join Date: May 2007
Location: Littleton, CO
Posts: 1,044
G.I.G. is on a distinguished road
G.I.G. G.I.G. is offline
Senior Member
G.I.G.'s Avatar
 
Join Date: May 2007
Location: Littleton, CO
Posts: 1,044
G.I.G. is on a distinguished road
Quote:
Originally posted by fishrod
What does this mean? The seals on the plugs need to be replaced when you remove them?
No, just the crush washers/gaskets. Not the plugs themselves.

I just hit 30k on my 4R and serviced all 3 boxes with Mobil 1 75W-90. Having the V8 with full-time 4-wheel drive I was noticing some binding when cranking the wheel hard (getting in and out of parking spots, flipping U-turns, etc.) but since I have switched to the Mobil 1, it is all but gone away. I am REALLY glad I went with the Mobil 1 and would highly recommend it regardless of whether you tow or not.
__________________
'07 Galactic Gray 4Runner Sport Edition 4X4 V8

Icon 2.5" coilovers with remote resi's | LT285/70/R17 Goodyear Duratracs | SCS Stealth 6 wheels | Light Racing UCA's | Bud Built front skid | Shrockworks Sliders | Toytec diff drop | Volant CAI | PIAA 520 ATP lights | Removed resonator, rerouted exhaust out the side | WeatherTech floor liners | Rear diff breather mod | GX470 driveshaft | Mobil 1 in all the boxes
G.I.G. is offline   Reply With QuoteReply With Quote
Old 05-15-2009, 04:21 PM #13
J.A.'s Avatar
J.A. J.A. is offline
Senior Member
 
Join Date: Jul 2007
Location: NY
Posts: 1,472
J.A. will become famous soon enough J.A. will become famous soon enough
J.A. J.A. is offline
Senior Member
J.A.'s Avatar
 
Join Date: Jul 2007
Location: NY
Posts: 1,472
J.A. will become famous soon enough J.A. will become famous soon enough
Quote:
Originally posted by fishrod
What does this mean? The seals on the plugs need to be replaced when you remove them?
The metal washer on the fill and drain plugs. There will be a couple different part numbers involved. You may be able to get a way without changing them, once perhaps, but Toyota specifies that they should be replaced. They are cheap insurance, if the dealer has them in stock.
J.A. is offline   Reply With QuoteReply With Quote
Old 05-15-2009, 04:53 PM #14
fishrod's Avatar
fishrod fishrod is offline
Member
 
Join Date: Nov 2008
Location: Kelowna, BC
Posts: 269
fishrod is on a distinguished road
fishrod fishrod is offline
Member
fishrod's Avatar
 
Join Date: Nov 2008
Location: Kelowna, BC
Posts: 269
fishrod is on a distinguished road
Quote:
Originally posted by J.A.
The metal washer on the fill and drain plugs. There will be a couple different part numbers involved. You may be able to get a way without changing them, once perhaps, but Toyota specifies that they should be replaced. They are cheap insurance, if the dealer has them in stock.
Ah cool thanks.

Just trying to weigh up whether I should have a crack at this myself or just let the mechanic do it for ~$300. Dont have any Tools, or car stands. How important is the Torque specs when tightening the plugs? How do you measure that? With the tools im guessing.
fishrod is offline   Reply With QuoteReply With Quote
Old 05-15-2009, 05:51 PM #15
Border411's Avatar
Border411 Border411 is offline
Member
 
Join Date: Sep 2004
Location: Fairfax, VA
Posts: 696
Border411 is on a distinguished road
Border411 Border411 is offline
Member
Border411's Avatar
 
Join Date: Sep 2004
Location: Fairfax, VA
Posts: 696
Border411 is on a distinguished road
You need a torque wrench. Lowes has Husky torgue wrenchs for a reasonable price, and they have a lifetime warranty. I suppose you could probably try to get your truck level enough just putting the wheels up on a curb (you will have to figure out the orientation for all that though!).
__________________
Shaun
2004 Titanium Silver Toyota 4Runner SR5 V6 4WD
265/70-17 LTX M/S, Bilstein 5100's Front (1 3/4" lift), DDM 35W HID 3000K Fogs, Silverstar High Beams, GE Nighthawk Low Beams, Showoff Krypton Hyper White Interior Bulbs, EGR Hood Protector, De-Badged, Husky Floor Liners (F/R), 3M Cabin Filter Mod, Fram SureDrain, Side Exhaust, Scion 1807 H/U
Border411 is offline   Reply With QuoteReply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Powered by vBadvanced CMPS v3.2.2

All times are GMT -4. The time now is 06:25 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger
 
Copyright © 2020