Recent content by 7harper

Super jca21!! That number does'nt cross on the US toyota parts site though. So , it must be a Canada only part and he'll have to call that guy in Vancouver to have it shipped. Also , not sure about emissions difference in Canada. That is unless he finds a Stant locking cap to work but...

Is it Toyota OEM?I guess it's a Canadian part, because it's not in the US parts manual. What's the part number to see if it can be ordered? There should be a 10 digit part number on it. I read this recently in another post ...to order Canadian parts " Call Vancouver Toyota Parts and ask...

Here is a link to a custom indash install. http://www.toyota-4runner.org/general-discussions/64565-ipad-toyota-dash.html

Is the one your missing for a 2010 right? SR5/Limited or Trail Edition? Which one as all 4 are different ? Front Limited, SR5 Model R 63491-35040 $47.93 L 63492-35040 $47.93 Trail Model R 63491-35030 $47.93 L 63492-35030 $47.93 Rear...

The 5th Gen Runners have dual cats attached directly to the exhaust manifolds on the engine.One on each side.You have to have access under the hood to get at the top bolts. Harry Houdini himself, in his prime ,couldn't have cut them off. If you own a 5th ,crawl up under there and check out your...

Let me get this straight. You know that the K&N lets more dirt into your engine but your logic is" Crap is always going to get in there regardless." With logic like that ,why use a filter at all ?Crap is always going to get in there regardless." Then it can really flow and you'll gain another...

Yep ,just the 2 inch Toytec spacer lift in the front only with stock rear.The Toytec 2 inch lift is actually a 1 inch CNC'd aluminum spacer that fits on top of the springs to get the lift. Little or no difference in ride quality but you will need an alignment as it throws the camber/caster out...

That's about what mine was stock.Check both sides as mine was 1/4" higher on the pass. side.Don't remember if the gas tank was full or not . The Toytec 2 inch lift spacer in the front gave me 1 3/4 inch front lift to make it just about level.

I used a spring compressor to compress the springs in the wheel well so I did'nt have to disconnect the hydraulic lines on my X-Reas shocks when I put the Toytec spacers in. It is definitely doable but one of the biggest pains and I would'nt advise anybody to do it on truck springs which have a...

The Toyota Land Cruiser Prado is the 4runners foreign cousin. They are built on the same frames and share alot of the same parts as the 4Runner and they sold just about all over the world except North America. Sweet rides , I wish they were easier and cheaper to import one to the states. No...

Here is a thread with what your talking about. It's the brake booster and normal. http://www.toyota-4runner.org/5th-gen-t4rs-its-finally-here/59049-10-brakes-help-needed.html

Right now I have a Toytec 2 inch front spacer lift. I'm putting on Icon coilovers and rear shocks for a 3/2 lift. UPS lost my rear shocks though. Long story short .....They say they were delivered to my front porch last Friday but they were not and it was insured and supposed to be sig...

That sounds more like it! The 5.71 backspacing would definitely rub on you UCA's. You can get a 3/2 lift and have some minor front trimming. Or you can get the Terra Grapplers in a 275/55/20 like most people and have no rubbing. 275/60/20 is a 32.99 inch diameter tire / needs lift and trim...

Ahh , I'm 7harper now. Still can't log into my harper7 account:fishing: Thinkin' the gators done ate gatorgreg!!lol A real pain for me when I had spacers/adapters on is my local Discount Tire said they were some kind of liabilty and would'nt put wheels on them. So when I went to recheck balance...

That is what he has...... As far as fitment goes!! You know wheels fits better then me as you were my mentor. What do you think he should do? There is no better fitment then a 8 inch wide rim with 4.5 backspace. That's a fact!