Recent content by ahermanson09

Yeah I used those exact pins in the picture, 4 and 14. When I am performing step number 3 however, everytime it is connected for the split second the VSC OFF / TRAC OFF go away while it is connected but then CRUISE CONTROL blinks, the airbag picture blinks and the ABS starts blinking. Ive never...

I forgot to post that. I have a 2003. I did read about the change for the 05 and newer models. I don't understand why my truck is not accepting it. I have had a 203 in the past and it had this issue but the first try that I did the zpc it worked. I am dumbfounded on why this one wont take it. I...

I think I will have to take it in. I called a couple of my friends to see if they have a scan tool that has the option to re calibrate through the tool itself but no luck. I am going to take it in after I get my 2 Inch front leveling spacer and new tires and rims installed and once I get it...

okay so I tried it again following the steps exactly and not disconnecting it after the 4 shorts and still no luck. When I did that, the trac off light went away and both abs and vsc trac lights were blinking (ABS faster than VSC light when blinking) and I also noticed the cruise control light...

Odd, yeah I did read that if the abs light blinks a certain pattern and another light blinks after that it is telling you a code of a problem. But mine is not. ABS works fine because I tested it in the snow the other day. I am going to try this solution and see what happens tonight at around...

From the TSB in step 3: 3. Using SST 09843–18040, repeat a cycle of short and open between terminals Ts and CG of DLC3 4 times or more within 8 seconds. Verify that the VSC indicator light is lit indicating the recorded zero point is erased. I took this as 4 taps and then leave it open. Not...

I am sorry my mistake, I had it on the ON position. But I didn't keep the wires connected on the fourth tap before I turned it off. I thought it was just 4 taps of the wires and then leave them apart and then turn off. I will try leaving the fourth tap connected and then see what happens. Thank you!

Yeah i was never able to get it successful to continue onto these final steps. EDIT: Are you saying during the steps of shorting them out 4 times in a row that the fourth time needs to stay connected and then turn the car off to proceed to the next set of steps?

Here are the complete steps and what happened that I did. 1- while car is on level surface and steering wheel straight and ignition off I plugged two wires, one in 4 and one in 14 2- turned the vehicle on accessory and tapped the two wires together 4 times and then left them apart but still...

I actually never fully disconnected it from the port itself, I left the two wires in pins 4 and 14 IN the port itself, but never fully took them out when turning the car off. Maybe that is where I messed up at. I will have to try that procedure right after work or maybe on my lunch break.

Yeah i checked the pin location and it all seems to be in order. I cant seem to figure out what the issue is. It blinks the abs light and the TRAC OFF light goes away when I connect the two together 4 times in a row and not the VSC light, that stays lit.

When you say disconnect the SST, do i completely remove it out of the OBD2 port? I did all the steps but I couldn't get the car to do anything past shorting it 4 times. If you recall did the ABS light blink like mine did when you performed this?

Have you ever performed the steps of calibrating? I do know the difference between the 03 vs the newer 05 model and the different steps of each but in my video when I complete 4 shorts in a matter of 8 seconds or less, the ABS light flashes and the TRAC light turns off but the VSC stays on. Is...

I had this printed out and when I got to step 3 - "Using SST 09843–18040, repeat a cycle of short and open between terminals Ts and CG of DLC3 4 times or more within 8 seconds. Verify that the VSC indicator light is lit indicating the recorded zero point is erased." ... the TRAC OFF light...

Zero Point Calibration - NEED HELP Okay so I have looked around on the various pages about the zero point calibration steps and how to reset the whole thing. I plugged a OBD2 tool into my 4runner and cleared a code after I replaced my spark plugs and everything works fine however I set the VSC...