Recent content by CoCoCo4Runner

  1. C

    Yet another rear suspension question

    To my knowledge it's a stock setup with an original 1998 spring with 250k miles, and a stock strut with 20k miles.
  2. C

    Yet another rear suspension question

    Appreciate the perspective. Right now my stock front end is 35.5/36" from ground to fender, rear is about 1.5" lower. I don't mind a bit of positive rake, but with new rears that would be about a 3-4" overall lift in the rear.
  3. C

    Yet another rear suspension question

    Long story short the rear suspension is shot, it sags and handles zero weight. If I stand on the hitch it probably drops a foot. I've done some research, and am looking hard at the OME 906/5100 combo. I am focusing more on the rears, as the front struts were replaced with OEM at the dealer by...
  4. C

    The 3rd Gen All Questions Allowed Thread

    Hadn't even considered airbags. Is this something I'd put in with my tired rear suspension?
  5. C

    The 3rd Gen All Questions Allowed Thread

    Going to ask here before making a new thread. I've had my 4runner for a few years and haven't really driven it all that much, it's very much a third car that I use for hauling people/things, or driving off-road. I also use it for shorter around town trips when it's warm and I can drop all the...
  6. C

    Water intrusion

    Well, that was easy. Stuck the hose on the roof and let it rain for a few minutes, immediately saw dripping from the sunroof seam. Now it isn’t too hard to imagine how a cups of water got into the cabin after having been rained on heavily for 12+ hours straight. At some point it had been...
  7. C

    Water intrusion

    Hi all, a recent storm surge revealed that I have a massive leak in the 4runner, the center console was filled with 2” of water, and the trans tunnel/drivers side carpet is very wet. It’s going to be raining all week, so aside from parking it indoors, where can I begin to check for leak spots...
  8. C

    3D Printable Headrest storage

    Weird, maybe only the Limited models?
  9. C

    What Did You Do To Your 3rd Gen Today?

    Yep I'm sure they are. And I needed cotter pins for the upper ball joint, the lower ball joint (I used OE Toyota) came with a new nut and cotter pin.
  10. C

    3D Printable Headrest storage

    Cool design, I'll have to load up some PETG and try it out. But aren't there holes in the seats when they're folded down where you insert the headrests?
  11. C

    What Did You Do To Your 3rd Gen Today?

    Installed new LBJ’s and associated bolts. Absolutely kicked my ass, I think most of the components could be original, end links looked tired and the LBJ were whooped. Torn boots and no idea how old they are, God forbid they were original… Took me about 90 min per side, between trips to...
  12. C

    1998 4Runner Small Mods

    Exhaust smells gassy, visible smoke when cold
  13. C

    The 3rd Gen All Questions Allowed Thread

    Back again with more questions. Question 1: Where does this lead? It’s coming out the back of the lower intake plenum on the driver side. I’ve got a somewhat unique situation, 1999 engine went into a 1998 4runner, but due to circumstances I only had either the donor intake manifolds or a set...
  14. C

    1998 4Runner Small Mods

    Yeah that may have been me haha! Unfortunately it's not running as well as I'd hope, running very rich with a high idle. Trying to chase down vacuum leaks to see if that's the cause.
  15. C

    99 3rd gen limited v6 running rich?

    Vacuum leak could be causing it as well, and something you can check without throwing too much money at the truck. My truck is also running rich :(

Members online

No members online now.

Forum statistics

Threads
278,306
Messages
3,554,045
Members
248,016
Latest member
Advally Service
Back
Top