Recent content by Devo9000

Hi. I found them at junkyards pretty easily. Most of them have a website where you can see what vehicles they have. I modified mine to extend the tracks and run another bar. Good luck Sent from my iPhone using Tapatalk

Clearing out 3rd gen stuff. Up for grabs is excellent condition rear axle housing and 3.9 diffs (so says axle code, I never actually checked) These were cleaned and sprayed with oil and stored in a covered tub in the shed. Housing was treated the same and had ends covered with plastic wrap and...

Ok guys, I got your PMs. Will be packaging stuff up and figure out shipping. Sent from my iPhone using Tapatalk

Clearing out the shed. Have : rear axle housing - non elocker, rust free and clean- pick up only front and rear diffs. 3.9:1 ratio - rust free and clean. Can ship for a fee Above parts off a mint condition 2002 with 120kmi Polyurethane 3” spacer lift USPS flat rate medium box Tacoma whip...

Running them on an 02 for a year. 8/9 perch with LC 8wraps with tokikos. Rides great, nice on road ride and handles high speed rough roads and tracks no problem. Run 33 x 10.5s on stock 15” alloys. No wheel spacers and No rubbing on control arms or fender wells. I do not have flares. I...

These are what Toyota supplied. Mine were all corroded and I replaced with these. Plug and play if you have the bracketry. HELLA H12090041 55 Watt H3 Type Micro Fog Lamp https://www.amazon.com/dp/B000VU96WW/ref=cm_sw_r_cp_tai_9gdmCbE5ETFT0 Plenty bright and can go yellow or white. Nice cut...

Cleaning out garage and found this brand new TV cable. Somehow got sent 2 of these when I rebuilt that tranny way back when. Have since sold the truck and have no need for it. Free plus shipping. Prob can fit in flat rate box. For stock auto trans in 3.0 pre96 trucks and runners Sent from...

I got injectors from flamethrower, I think he’s on eBay. This was for my ‘90 p/u. I think he does for the 3rd gen too. He’s got a lot of positive input over on yotatech. Good price too! Sent from my iPad using Tapatalk

For the under carriage I’d go pressure washer. That’s how I did mine when I first got my runner years ago, thick caked on grease. For the engine bay, I use a very greasy rag. Scrape the thick stuff off with a stiff plastic scraper and wipe the rest with a greasy rag. You want that grease...

I put an FJ knob on my j shift transfer that i swapped into my 02. Looks good and fit perfect. Never liked that original weeny knob. Got it off eBay for like $12. Sent from my iPad using Tapatalk

I went with land rover disco 2 seats. Much more comfortable for taller broader shoulders. Seat tracks are same width. Remove feet from yota seats and weld on to rover tracks. These seem to be around in the junkyards in much better condition than yota seats. Also there’s an outfit that makes...

I also had same issue, but it wasn’t intermittent. Was a cheap fix. $100 j-shift transfer case and a pair of shafts from a ‘96. Always goes into gear now.[emoji38] Sent from my iPad using Tapatalk

Have a look at the billstein 6112s. I just put them on in the last year and am plenty pleased. A sort of step up from a standard set without the price tag of kings or fox. For my purposes a racing shock was not necessary. I think I paid about $800 . Sent from my iPad using Tapatalk

You’d run the newer 6112s because the piston and oil capacity is much larger than the older 5100 Sent from my iPhone using Tapatalk

4Runner 6112s on 8 and 9 perch LC 7wraps rear 33s Spoke with MRT in Vegas about very same thing...more stiffer ride they say. My setup is great on crap bumpy roads at speed and off-road high speed dirt tracks Not too shabby crawling Sent from my iPhone using Tapatalk