Recent content by Ele'ele

I made a post long ago about my magnaflow installed. I also had the drone about 1700 rpm and thought I could take it. But after 2 weeks I took off my cat back and put the stock system on. I just could not live with that constant drone, especially since I was always driving in the 1700- 2000 rpm...

Hey Mike, I purchased wheel spacers from Fred Goesk and I could not be happier. Excellent workmanship, knew what he was doing, and knew what he was talking about. I paid about $350 and took about 1 week to order and receive the product. I did pay extra to have the lip on the spacer made...

tint In Tennessee, the law is strict and can only put 35% on the front. Like you mentioned it is way too light to match the rest of the 4runner. So I just drove over the state line to Arkansas and had them put another smoke film of 35% over the high performance 1st film. Matches and looks...

I still have stock mud guards on. My tires stick out about 1 inch from wheel wells, so my runner does get somewhat dirty but no big deal. I cut and heated my mud flaps to fit.

inner wheel trim You do not need to cut your trim. My tires also rubbed after i installed my 1.5" wheel spacers on stock rims with 265's. I cut some but the majority of the plastic, I just got a good lighter, heated up the trim and remolded the touching plastic inwards. Just keep pressure on...

rattles I have had rattles from my drivers side roof, and also very bad rattles from my sunroof area, and rattle from my drivers side sunvisor. In an attempt to quiet the sunroof rattle because it was the worst I sprayed the home depot expanding foam into the rear of the sunroof, about 2 full...

spacers I think I paid about $350. My spacers from fred also has the outer lip on the spacers which secures the rim to the spacer for even greater strength. I did not post pictures as I attempted to earlier on but failed. I am having a hard time with the picture thing. But look up fred on the...

One more thing, Because of the extra width, I had to trim some of my inner front wheel well trimmings. Only a little. The rest of the wheel well, What i did was to get a lighter and heat up the plastic and then just remold it inwards so that it does not touch. @85's will fit with lift but there...

I installed 1.5 inch spacers, giving me 3 inches of extra width. I did this to off set my 3 inch Revtek lift. My 4runner still handles great, too great! The tires stick out from the body about 1 inch. Not noticeable but you do see the extra width from the front and rear. I have the expensive...

air lift I just installed a airlift kit for my 2004 4runner, rear kit. It took about 5 hours to install. It was not hard. You have to disconnect the panhard and sway bars, drop the rear axle and install the air springs. Then figure out where you want to mount the air copressor, do the wiring...

1. Good Times (Lance) 03 SR5 V8 4x4 2. chiefiji (henry) 04 SR5 V6 4x4 3. On Fly (Juan)03 Sport V8 4x4 4. ssmathis (Scott) 05 Limited V8 4x4 5. Toybox (Joe) 03 Sport V8 4x4 6. kglueck (Kevin) 04 Limited V8 4x4 7. Bobby (Bobby... duh) 04 Sport V8 4x4 8. No-IP.com (Joel) 04 Limited V8 4x4 9...

Magnaflow Hey Huntrunner, I just purchased and installed the Magnaflow catback system for my 04 4runner V8. The system is awesome and the sound is great. It has aggressive V8 sound of a Mustang GT when I accelerate. There is a definite drone at about 2000rpm and this does not really go...

Ft. Drum I used to be stationed @ Ft. Drum 1989 -1991. It gets very cold but not cold enough to have an engine block heater. Just change your oils according to the seasons. But you will definitely benefit from the 4WD as I had a 4WD Jeep Cherokee. I was with 3/25 aviation brigade, Huey...

pictures Hey Iforce, how do I post pictures?

Hope this attachments work. Pictures of TRD air filter and modified intake.