Recent content by garface

LFD Off-Road Ruggedized Crossbars Socal/LA I've got a set of 3 LFD Aluminum Crossbars plus bolt-on wind fairing as well as a bag of a bunch of hardware. They're for the 5th gen factory rack or use with their side rails for 5th gen. These are the earlier version of the crossbars with...

I'm a little scared to imagine how much it would cost to ship them unfortunately haha. It's just a little more logistics than I'd like to deal with if I can potentially sell them locally, sorry about that. Maybe if I still have them in a couple weeks we'll talk?

Apologies for the delay in response, wanted to dig up my original receipt so I could get you accurate info. Tires and wheels were purchased together in September 2017. They have 36,600 miles on them give or take a few. I do a fair amount of off roading but I'm not a big rock crawler so they...

285/70/R17 BFG Ko2 w/ Method Mesh Wheels EDIT: SOLD Hey Guys, Selling my set of 4 wheels and tires, Posted in classifieds section, please see link for more details. 285/70/R17 BFG Ko2 E rated w/ Method Mesh wheels and lug nuts. Inflated and ready to go, no TPMS. Located in Long Beach But...

Method Mesh w/ BFG KO2 $1k OBO SoCal EDIT: SOLD Hey Guys, Posted this on the classifieds section, but selling my wheels/tires off my 5th gen. 285/70/R17 BFG Ko2 with Method Mesh Wheels See the link for more details. Thanks!

What they look like on a truck (taken the day before I swapped them)

Edit: SOLD Hey Everyone! I just changed up my wheel/tire setup and my old set of 4 needs a new home! Tires have around 35k miles on them, still in absolutely great shape and will keep on rolling for quite some time. They've been super strong and durable and I haven't had a single issue with...

How's the fitment of the wheels? Pretty straightforward install or did they require any special parts? Haven't found a clear answer whether or not they are hub centric. Looks good though, I'm just about to ditch my current wheel/tire combo in favor of something way lighter and more subtle, it's...

I have a set of Icon 2" rear springs for sale. Used for 1year/ 20k miles. No issues, I just decided that it ended up a little taller than I needed, so I changed to Wheeler's T13's. Would prefer to pick up/drop off locally, but I have the packaging from my T13s and can ship if needed. I basically...

I'm curious about the height comparison between the stock roof rails w/ LFD crossbars and the LFD side rails with crossbars. Anyone know if they are much different? From looking at the sharkfin antenna in photos, looks like the LFD side rails are a little bit higher than my current setup with...

This looks almost like the bushings were greased through the zerks without loosening the pivot bolt first. this is something that absolutely necessary to prevent the bushings from expanding and getting wrecked. check out this instruction from total chaos...

Update: As of today I have a quiet truck finally! While prepping to install my Pelfrybilt sliders, I washed the truck, buffed out some pinstriping, and waxed it. I also figured I'd put some fresh grease in the UCA bushings, as I go out to the desert almost every week and a bunch of grease has...

Drove from LB to SD, spent almost 6 hours in the truck due to traffic, to pick up my new sliders from Pelfreybilt. Took them home, prepped for 2 hours and painted for 3. Washed the truck while the sliders dry overnight. And got a shiny new red shift knob from AJT designs put in and some new...

Good point. I'll get out there and check that today, had it in the alignment shop yesterday and have gone to the same place every time so that would explain it if they're using the lower torque value. Thanks for the tip!

I've been dealing with the exact same thing. Installed my Kings w/ Total Chaos UCAs and it was squeaking a day later. I know that polyurethane bushings and uniballs make more noise by nature but I'd like to see what I can do to make it as quiet as possible. And "race truck suspension makes race...