Recent content by lbro23

  1. lbro23

    What did you do to/in your 5th Gen today?!

    Finally finished my sleeping platform build. The two inserts are independent, so I can take out the driver's side and run a 3rd seat if I need to.
  2. lbro23

    What did you do to/in your 5th Gen today?!

    I finally got fed up enough with having to take bikes off of my bike rack to be able to get into my trunk, so I braced a hitch receiver I had laying around and mounted it to my swingout. What's that old saying about a grinder and paint???
  3. lbro23

    5th Gen For Sale/Wanted Thread

    FS: 4Runner OEM Parts North Atlanta All parts have been on the car for 100k miles and are used but in fully functioning condition. Located in Alpharetta, GA OEM Fog light assemblies Pair L&R: $30 OEM Roof rails, crossbars, seals, and associated hardware: Free to pick up (Edit: silver TE...
  4. lbro23

    What did you do to/in your 5th Gen today?!

    There is also the 275. Best (or worst) of both worlds, depending on whether or not they rub! Good Luck!
  5. lbro23

    WTB 1up Hitch Rack (Co Front Range)

    1up requires you to wait on a waitlist for 6 weeks for the privilege of paying them, and then waiting an additional 6-8 weeks for a rack. So in the mean time, I figured I'd put out a feeler on here: Want To Buy 1up HD or Super Duty Hitch Rack (2+ bikes). Silver or Black, 2" Hitch Receiver...
  6. lbro23

    5th Gen For Sale/Wanted Thread

    WTB 1up Hitch Rack 1up requires you to wait on a waitlist for 6 weeks for the privilege of paying them, and then waiting an additional 6-8 weeks for a rack. So in the mean time, I figured I'd put out a feeler on here: Want To Buy 1up HD or Super Duty Hitch Rack (2+ bikes). Silver or Black, 2"...
  7. lbro23

    5th Gen For Sale/Wanted Thread

    What are they? Judging by your pricing I'd assume the MAX in fog pattern?
  8. lbro23

    HELP Please!! - Intermittent ABS/VSC/TRAC Light Issue

    Looks like you're paying an extra $200 for an inch of breather tube, and some sort of extra mounting plate/bolt. The castings and I'm sure the wiring are identical. I don't usually trust the listed compatibility on Amazon, but Summit racing (who I do trust) lists the 009 for up to the '09...
  9. lbro23

    HELP Please!! - Intermittent ABS/VSC/TRAC Light Issue

    With this new information, here's theory #2: There is some intermittent short in the locker indicator switch that is causing the 4wd ECU to think its locked. When this happens, you get lights because ABS and VSC are disabled whenever you're locked up, and you get the blinking diff lock light...
  10. lbro23

    HELP Please!! - Intermittent ABS/VSC/TRAC Light Issue

    It seems unlikely that it'd be a bad calibration, as it wouldn't be such an intermittent problem. It definitely sounds like one of the sensors that feeds into the TC/VSC systems is having some intermittent issues. But ABS sensors wouldn't cause problems at a standstill, and a vehicle speed...
  11. lbro23

    How does the 5th gen fit tall drivers?

    My right knee will adjust the fan speed if I get in or out quickly, otherwise while driving its not a problem. 6'5" and fit fine in a 2014 w/ no sunroof, but only as the driver (seat all the way down, but still has a few more inches back). My head touches the ceiling as a passenger as the seat...
  12. lbro23

    Strange noise, help diagnose?

    Did you get the truck aligned after installing the lift? Perhaps the alignment is off, or just different than before and you're getting additional tire noise as a result. I notice my tires are slightly louder right after I rotate them before they "wear" into their new place (100ish miles).
  13. lbro23

    Air Ducting Attached to Skid Plate

    There is indeed a forward facing vent that some skid manufacturers replicate in different ways. But I think what you're referring to as ducting is the factory jacking point (that happens to be hollow to let air pass). Most aftermarket skids are just strong enough as is to jack from. If you're...
  14. lbro23

    What did you do to/in your 5th Gen today?!

    I see you've got a 1up on the swingout of what appears to be a CBI bumper. How do you like this setup? Do you have any close-up pictures of how they attach? I've got a single swingout but am looking to weld on a hitch receiver. Having to take bikes off just to get into the trunk is driving me...
  15. lbro23

    KDSS sway bar end link bushing updated with flanges?

    Kind of related question, but does anyone know how to go about changing the bushings on the piston/solid link? I want to do all 4 at once.

Members online

No members online now.

Forum statistics

Threads
278,310
Messages
3,554,079
Members
248,016
Latest member
Advally Service
Back
Top