Recent content by SilverBullet01

yea, the rust free is quite the luxury. I may pay WAY too much for rent but it's one of the biggest perks for living in California. So I pulled out the old harness and saw that I could not remove the harness from the plug. I fully replaced the factory harness and plug with one that was...

In case it isn't obvious I did drop the spare to give me more space to work with. Spare is back in place so no more good photos of the harness, and wiring is cleaned up. Thank you everyone for the photos and suggestions!

Alright everyone, I finally got to it and got everything up and running. So I ended up ordering this harness on eBay...

ok this is looking like a really easy solution. Im liking this a lot. Thank you for the idea! I tow rarely, I use a hitch mounted bike rack the most, but I wanted a way to revert back to factory if I needed and this seems like the ticket. I already ordered a different wiring harness that has...

Honestly I thought about it. Wiring I have no issues with. If I do this im going to tap into the existing trailer hitch wiring since I won't have to run as long of a cable for it. I just need to tap 4 wires and make a new harness and since I can get the old harness out I can solder everything vs...

this is exactly what I was looking to confirm. Thank you!

I just recently swapped my oem coils out on my 05 for fresh Dobinsons. I thought I was getting a 2 inch lift, but the wheel to fender distance increased from 3 inches to about 7. So in theory a 2 inch lift also compensated for 2 inches of sag over that time.

So this is the route im taking currently. I have ordered this harness off of eBay. https://www.ebay.com/itm/297691429248 Figured I would see if this works to replace my existing factory plug, and order the 4pin harness from Diode. Stage Series C1R/C2R 4-pin Single-Output Trailer Wiring Harness

So in the second picture, im trying to remove the harness from the backside of that plug. Are the harness and plug all once piece because I think they might be. That's the exact spot I need to separate.

I see the two plugs for the harness to remove and replace the entire harness. Looking at it further, it seems that the only removable part is the entire plug/harness piece and its not removable from the back of the 7 pin itself to add this harness in line. I will probably be ordering their 4 pin...

after looking at it a bit more, I don't know if the factory 7pin plug is removable from the included wiring harness. I hope I am wrong because this would be so much easier to install, but I may have to cut the wiring from the Diode Dynamics harness and tap into the existing factory wiring and...

<blockquote class="imgur-embed-pub" lang="en" data-id="a/sFXrL5B" data-context="false" ><a href="//imgur.com/a/sFXrL5B"></a></blockquote><script async src="//s.imgur.com/min/embed.js" charset="utf-8"></script>

Im attempting to disconnect the back of the 7pin to add this wiring harness in line with the existing to the 7pin plug. This hitch light came with an inline harness and I can't seem to get the back of the harness off the plug to add this in line. I will try and take some photos of what im...

Ive always been a JL audio fan, not sure now after they were purchased by Garmin. I do love their stealth box setup. looks super clean. A bit more expensive but it packs a good punch. JL Audio SB-T-4RNR2/10W3v3/TP Stealthbox(R) for 2003-2009 Toyota 4Runner with Taupe interior | Competition...

Hey team, I've been googling and searching the forums for quite some time and Im running into an issue. I am attempting to remove the trailer hitch wiring (temporarily) so I can mount a wiring harness in line. For the life of me I can't seem to figure out how to press, squeeze, or pry off this...