Recent content by trd6209

As soon as it stops snowing I will post some photos. Matt Sent from my Pixel 5 using Tapatalk

So all I needed to do was connect the RCA video cable from the main harness to a secondary harness toake the backup camera work. Actually pretty simple if they would have described the install adequately. First impression is favorable but most of the features are pretty slick. Many of them I...

I just bought it and am in the process of swapping over. My backup camera isn't working, so I have a request in for tech support. The trim is flat and a little bit cheap looking but the screen looks nice. I will let you know how it goes. I have installed.probably 15-20 stereos in my life and if...

I know that this thread is a little bit older, but I purchased this for my 2016 Trail and my backup camera doesn't work. I get an big yellow exclamation point on the screen when I go into reverse. Did you have any issues with this?

I went with C4 Fabrication sliders and I love them. Bolted right up. No issues. Beautiful sliders and pretty low profile, but still gives the rig character. Sent from my Pixel 5 using Tapatalk

I had a similar install issue with mine and I found that I made the problem worse when I plumbed up the ladder. When I installed the ladder in place with the edge of the top bracket at 4.5 inches and pulled everything down tight I had no rubbing. In that position the bottom of my ladder...

Finally got around to installing my Method Racing NV 305s and 285 KO2s. Love the look and the ride Sent from my Pixel 3 XL using Tapatalk

I am thinking of this as well being from NJ. I will probably drill 2 holes in the bumper to the left or right of the fairlead and install 2 Rivnuts to accept the bolts. Should work well. I hate the idea of the flip up license plate. On a side note I just received my SSO roof rack. They didn't...

They do rattle a bit but 8t doesn't bother me. I like having them accessable. Could easily put them in a molle pouch and keep them quiet. I do like having this stuff up and off the deck. Sent from my Pixel 3 XL using Tapatalk

Maybe my logic is flawed, but if people run stock with 2 inch coil spacers I would think running 2 inch lift shocks with a 3 inch coil spring setup (2 inch 8con spring + 1 inch spacer) would be less detrimental to performance. If I did see an issue I think it would be at extremes of travel. If I...

I saw that the HD springs when purchased as a standalone item note that theyse springs will increase height by .5 inches. On the B8 6112 kit it says 2.6 for non-KDSS so I am guessing that's somewhere around 3.2 or so. Maybe actually a little taller for my application. Sent from my Pixel 3 XL...

Lesson learned. All in all I am wishing I would have just done the Icon stage 2 kit. At least I could have spanner wrenched my fronts to level it as opposed to tearing the entire thing back apart. May try to take some readings and see where it sit before 8 do anything else. Didn't want a...

Well I'm already "pregnant" with the HD springs so there isn't much to do about it now except for lowering my settings about 1/2 inch. I am already running C4 rock sliders and my SSO full roof rack. My next add is a winch bumper and winch. I do intend to have an RTT, but it won't be...

So according to the Bilstein instructions it looks like the height should be the same at Max (2.6) for non KDSS. It also shows that max for the B8 6116 struts is snoring settings 6 & 4 and not 7 & 5 like I have seen others post. What is odd is that according to Wheelers website there was a...

Correct, no KDSS. Sent from my Pixel 3 XL using Tapatalk