Toyota 4Runner Forum - Largest 4Runner Forum

Toyota 4Runner Forum - Largest 4Runner Forum (https://www.toyota-4runner.org/)
-   5th gen T4Rs (https://www.toyota-4runner.org/5th-gen-t4rs/)
-   -   Just checked my oil catch can.. (https://www.toyota-4runner.org/5th-gen-t4rs/271698-just-checked-my-oil-catch-can.html)

jahdai42 04-17-2019 08:43 PM

Just checked my oil catch can..
 
So I put this sucker on 22 days ago and it already has an ounce of oil in there. It is also pitch black. I should have got one of these when it was new.

Volke 04-17-2019 09:32 PM

The oil in your catch can isn't necessarily an accurate representation of what's in your engine unless you have let it sit for a long time. It gets black and gunky from the moisture, but the oil in your engine burns most of that off when it gets hot enough. The oil in the catch can stays at roughly ambient temperature under the hood.

57buick 04-17-2019 11:31 PM

2 Attachment(s)
I installed one a couple weeks ago, looking forward to seeing what mine catches.

wcjeep 04-17-2019 11:58 PM

I could see a benefit if the vehicle was subject to long term steep incline/decline. Not sure what the benefit would be for normal daily driving. It's designed to go without the catch can.

jahdai42 04-18-2019 07:23 AM

Quote:

Originally Posted by wcjeep (Post 3273888)
I could see a benefit if the vehicle was subject to long term steep incline/decline. Not sure what the benefit would be for normal daily driving. It's designed to go without the catch can.

It really is just to keep that gunk out of the intake plenum. Nothing more.

Mantilgh 04-18-2019 09:14 AM

Just checked my oil catch can..
 
Quote:

Originally Posted by wcjeep (Post 3273888)
I could see a benefit if the vehicle was subject to long term steep incline/decline. Not sure what the benefit would be for normal daily driving. It's designed to go without the catch can.


Because that oil vapor condenses in the in the intake system and coats it. It can build up in the intake runners and on the back of the valves, more so on direct injection engines. It can coat and cause issues with the throttle body if it’s plumed in before it. The vaporized oil mixture is also probably not great for the combustion process, because it’s messing with the air/fuel ratios

The system is there for emissions/EPA.




Sent from my iPhone using Tapatalk

97BlackAckCL 04-18-2019 11:37 AM

Quote:

Originally Posted by 57buick (Post 3273879)
I installed one a couple weeks ago, looking forward to seeing what mine catches.

Any write up or detail of the install for this?

57buick 04-18-2019 06:59 PM

3 Attachment(s)
Easy install. First I bought the catch can below on Amazon. After doing research on catch cans and decided what kind of internal construction was best for catching contaminates.

Second, I removed that factory bolt on front of engine in picture, it had a small lip sticking out on factory bracket that kept my bracket from sitting flush so i ground that tab off, drilled a hole in my catch can bracket and bolted it back on.

Third, replace the pcv hose with your own hose going from the pcv to the catch can, then run a second hose from catch can to where the PCV valve originally went back into engine.

https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

Mantilgh 04-19-2019 01:35 AM

Just checked my oil catch can..
 
After saying what I said earlier. It really isn’t all that harmful in general, possibly depending on the condition of the engine.

But if you’re a person that buys vehicle and keeps it, it is a preventative measure. I think it’s something that should help keep the intake track cleaner, possibly helping reduce problems later.

I just pulled the intercooler off my 02 WRX thinking it would help me get to a hose I need to replace.

Stock PCV set up, which is routed in just before the turbo. 280,000 miles

Turbo outlet

https://uploads.tapatalk-cdn.com/201...a1f9985eae.jpg

Throttle body

https://uploads.tapatalk-cdn.com/201...bf989146f6.jpg

Could be worse, but could be better. I imagine there’s decent amount in the intercooler too because of the lack of it on the TB.





Sent from my iPhone using Tapatalk

Wrexeter 04-19-2019 02:41 AM

Quote:

Originally Posted by Mantilgh (Post 3274530)
After saying what I said earlier. It really isn’t all that harmful in general, possibly depending on the condition of the engine.

But if you’re a person that buys vehicle and keeps it, it is a preventative measure. I think it’s something that should help keep the intake track cleaner, possibly helping reduce problems later.

I just pulled the intercooler off my 02 WRX thinking it would help me get to a hose I need to replace.

Stock PCV set up, which is routed in just before the turbo. 280,000 miles

Turbo outlet

https://uploads.tapatalk-cdn.com/201...a1f9985eae.jpg

Throttle body

https://uploads.tapatalk-cdn.com/201...bf989146f6.jpg

Could be worse, but could be better. I imagine there’s decent amount in the intercooler too because of the lack of it on the TB.





Sent from my iPhone using Tapatalk

A turbo with a lot of miles on it will leak oil past its seals. At 280k miles, that shaft probably has a lot of play in it, and likely lets a lot of oil past its seals.

Every turbo car will burn oil, which means it is also putting it into the intake system as well.

So yes, if you look in your intercooler, it will have oil in it. Its also why those rubber intake hoses feel oily... the pressure eventually makes them leech oil.

WAT4R 04-19-2019 09:28 AM

Quote:

Originally Posted by 57buick (Post 3274353)
Easy install. First I bought the catch can below on Amazon. After doing research on catch cans and decided what kind of internal construction was best for catching contaminates.

Second, I removed that factory bolt on front of engine in picture, it had a small lip sticking out on factory bracket that kept my bracket from sitting flush so i ground that tab off, drilled a hole in my catch can bracket and bolted it back on.

Third, replace the pcv hose with your own hose going from the pcv to the catch can, then run a second hose from catch can to where the PCV valve originally went back into engine.

https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

What size / type hose did you use?

57buick 04-19-2019 10:30 PM

Quote:

Originally Posted by WAT4R (Post 3274617)
What size / type hose did you use?

cant remember think it was 3/8

Texas_Ranger 04-21-2019 10:51 AM

1 Attachment(s)
Its a 3/8 OD vacuum line but the fitting from the crankcase is slightly smaller then the one going into the upper manifold. For the smaller one you might want to use a ring gear to tighten it down. I used the spring that was one it and a zip tie to tighten it down even more so. I put mine in yesterday.

4RunnerAquasport 05-24-2019 02:24 PM

2 Attachment(s)
Installed mine today. I have too much other crap mounted in various places around my engine bay, so I had to come up with an alternative and secure spot. The drivers side intake bracket works quite well and the whole assembly is easily removed when I need room to work. @wfo9 thanks for the Moroso recommendation.

SparkySparks83 06-25-2019 12:30 PM

Coming from a high boost direct injection platform where it was common to us an oil catch can to keep thing clean and running smooth. The occ should be mounted so it is the lowest point in the system so any oil vapors in the hose run back into the catch can.


All times are GMT -4. The time now is 06:30 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger