Toyota 4Runner Forum - Largest 4Runner Forum

Toyota 4Runner Forum - Largest 4Runner Forum (https://www.toyota-4runner.org/)
-   5th gen T4Rs (https://www.toyota-4runner.org/5th-gen-t4rs/)
-   -   Westcott TRD Pro Kit Installed (https://www.toyota-4runner.org/5th-gen-t4rs/290553-westcott-trd-pro-kit-installed.html)

volfan615 09-26-2020 07:32 PM

Westcott TRD Pro Kit Installed
 
Had my Westcott Designs lift installed yesterday and then today installed 285/70 Wildpeaks and had alignment done. It looks great and actually rides better than before.

Measurements for center of hub to fender:
RF Before 21 - After 23
LF Before 21 - After 23.25
RR Before 22.5 - After 23.75
LR Before 22.5 - After 23.75

Before
https://i.imgur.com/E3uc4Ui.jpg

After
https://i.imgur.com/aE5zUJ1.jpg

Final result with 285/70 Wildpeaks
https://i.imgur.com/Pj8Hwdu.jpg

plummerg 09-26-2020 07:41 PM

Looks great!

DENviaATL 11-20-2020 11:26 AM

Did you have to do a dif drop or anything else?

edgesalon 11-20-2020 01:22 PM

Quote:

Originally Posted by volfan615 (Post 3548601)
Had my Westcott Designs lift installed yesterday and then today installed 285/70 Wildpeaks and had alignment done. It looks great and actually rides better than before.

Measurements for center of hub to fender:
RF Before 21 - After 23
LF Before 21 - After 23.25
RR Before 22.5 - After 23.75
LR Before 22.5 - After 23.75

Before
https://i.imgur.com/E3uc4Ui.jpg

After
https://i.imgur.com/aE5zUJ1.jpg

Final result with 285/70 Wildpeaks
https://i.imgur.com/Pj8Hwdu.jpg

looks great did you do the install or had a shop do it and may i ask how much to install the lift thanks

JRod0981 05-28-2021 04:24 PM

Just found out about this lift today when talking to a local shop about lifting my 4runner. Super affordable in comparison to the other toytec/dobinsons lifts I was looking at. And I have a lower header in my garage so i'm worried when I have my ski racks on about getting close to the top of my garage after a lift.

On their web site it says it's not a spacer/body lift but having a hard time not seeing that. Did you have to do upper control arms to fit the 285/70/17 wildpeaks at all or just the lift?

Stephencovar 06-19-2021 09:21 AM

Your rig looks great! Out of curiosity, what’s the finally ride height in the rear from the ground to the top of your TRD roof rack? I want to get this lift but I’m concerned about not fitting in my parking garage at work. The vehicle limit is 6’8”. I believe my rig is sitting at 6’5” with stock size KO2s.

I also want to get 285s but don’t want to mod the body, including removing mud flaps. Are you having any rubbing issues?

Brick Sprickly 06-19-2021 10:15 AM

Quote:

Originally Posted by Stephencovar (Post 3648453)
Your rig looks great! Out of curiosity, what’s the finally ride height in the rear from the ground to the top of your TRD roof rack? I want to get this lift but I’m concerned about not fitting in my parking garage at work. The vehicle limit is 6’8”. I believe my rig is sitting at 6’5” with stock size KO2s.

I also want to get 285s but don’t want to mod the body, including removing mud flaps. Are you having any rubbing issues?

285s on a stock Pro will require some trimming if you don't have an accommodating lift beyond the standard Pro lift. You can go up to 275s w/o trimming.

Stephencovar 06-19-2021 01:14 PM

Quote:

Originally Posted by Brick Sprickly (Post 3648467)
285s on a stock Pro will require some trimming if you don't have an accommodating lift beyond the standard Pro lift. You can go up to 275s w/o trimming.

Do you think I’d need trimming if I were to go with the Westcott lift?

Rottwagon 06-19-2021 02:50 PM

Quote:

Originally Posted by Stephencovar (Post 3648498)
Do you think I’d need trimming if I were to go with the Westcott lift?

I went with 285s with the Westcott and did not have any rubbing or require any trimming.

Brick Sprickly 06-19-2021 11:35 PM

Quote:

Originally Posted by Stephencovar (Post 3648498)
Do you think I’d need trimming if I were to go with the Westcott lift?

Yeah listen to Rottwagon as I have no experience with that lift.

Stephencovar 06-20-2021 10:35 AM

Quote:

Originally Posted by Rottwagon (Post 3648529)
I went with 285s with the Westcott and did not have any rubbing or require any trimming.

This give be a lot more confidence in placing my order. May I ask, what is the final ride height from the ground to the top of the TRD Pro basket? I just want to make sure I fit inside the parking garage at work.

Sr. Carrots 09-25-2021 02:46 PM

Wonder how the ride is with the Westcott lift? Thinking about installing one on my ‘16 Pro.

spartacus 09-26-2021 10:10 AM

Quote:

Originally Posted by Sr. Carrots (Post 3675766)
Wonder how the ride is with the Westcott lift? Thinking about installing one on my ‘16 Pro.

Since you are in', " the state of confusion". i will copy it from the first post of this thread.
Measurements for center of hub to fender:
RF Before 21 - After 23
LF Before 21 - After 23.25
RR Before 22.5 - After 23.75
LR Before 22.5 - After 23.75

Sr. Carrots 09-27-2021 12:26 PM

Ride quality; no confusions regarding ride height, but thanks.


All times are GMT -4. The time now is 01:49 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***Ad Management plugin by RedTyger