Media added by SidKo

Navigation

Browse albums

Trending media

Democratic Point, Long Island, NY

Democratic Point, Long Island, NY

  • Media owner SidKo
  • Date added Jun 17, 2019
  • Reaction score 0
  • Comments 0
Cut off of the Morimoto XB lights. Used a blanket to cover the low beams while aligning the Morimoto fog lights.

Cut off of the Morimoto XB lights. Used a blanket to cover the low beams while aligning the Morimoto fog lights.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
The Morimoto pins had to be widen a tad bit.

The Morimoto pins had to be widen a tad bit.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
Once you test the polarity and confirm it works, attach the connector.

Once you test the polarity and confirm it works, attach the connector.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
Testing the polarity before attaching the connector to the Morimoto fog lights.

Testing the polarity before attaching the connector to the Morimoto fog lights.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
Make sure the alignment screw is snapped back into place.

Make sure the alignment screw is snapped back into place.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
Pushing back and securing the alignment screw when attaching old mounting bracket to the Morimoto fog lights.

Pushing back and securing the alignment screw when attaching old mounting bracket to the Morimoto fog lights.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
After placing the OEM mounting bracket, place back the plastic screw that used for the alignment of the fog lights.

After placing the OEM mounting bracket, place back the plastic screw that used for the alignment of the fog lights.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
OEM fog light mount removed/separated from light fixture.

OEM fog light mount removed/separated from light fixture.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
OEM fog fixture without its mount.

OEM fog fixture without its mount.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
To remedy the large gap between the Morimoto fog light lens and the housing that it sits in, I decided to swap out the mounts. Top is OEM and bottom i

To remedy the large gap between the Morimoto fog light lens and the housing that it sits in, I decided to swap out the mounts. Top is OEM and bottom i

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
Morimoto installed into position. Notice the large gap between the lens and the housing on the bumper.

Morimoto installed into position. Notice the large gap between the lens and the housing on the bumper.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
Left is OEM fogs and on the right is the Morimoto XB fog lights.

Left is OEM fogs and on the right is the Morimoto XB fog lights.

  • Media owner SidKo
  • Date added Nov 30, 2018
  • Reaction score 0
  • Comments 0
Some thing left a deposit under the hood.

Some thing left a deposit under the hood.

  • Media owner SidKo
  • Date added Nov 16, 2018
  • Reaction score 0
  • Comments 0
Headlight Switch

Headlight Switch

  • Media owner SidKo
  • Date added Nov 5, 2018
  • Reaction score 0
  • Comments 0
Trail edition rocker trim by Shrockworks. Rust on the mounting hardware provided by Shrockworks.

Trail edition rocker trim by Shrockworks. Rust on the mounting hardware provided by Shrockworks.

  • Media owner SidKo
  • Date added Oct 7, 2018
  • Reaction score 0
  • Comments 0
Trail edition rocker trim by Shrockworks. Rust on the mounting hardware provided by Shrockworks.

Trail edition rocker trim by Shrockworks. Rust on the mounting hardware provided by Shrockworks.

  • Media owner SidKo
  • Date added Oct 7, 2018
  • Reaction score 0
  • Comments 0
Empty switch located below the push to start button for the Sprint Booster controller.

Empty switch located below the push to start button for the Sprint Booster controller.

  • Media owner SidKo
  • Date added Aug 1, 2018
  • Reaction score 0
  • Comments 0
Sprinter Booster installed. Be careful not to zip tie excess controller cable to the heater core. It gets very hot and could potentially melt the zip

Sprinter Booster installed. Be careful not to zip tie excess controller cable to the heater core. It gets very hot and could potentially melt the zip

  • Media owner SidKo
  • Date added Aug 1, 2018
  • Reaction score 0
  • Comments 0
TRD Cold Air Intake installed on the Limited.

TRD Cold Air Intake installed on the Limited.

  • Media owner SidKo
  • Date added Jul 18, 2018
  • Reaction score 0
  • Comments 0
Installing the Morimoto XB (Oval) LED fog lights. Driver's side has the Morimoto fog lights installed.

Installing the Morimoto XB (Oval) LED fog lights. Driver's side has the Morimoto fog lights installed.

  • Media owner SidKo
  • Date added Jul 4, 2018
  • Reaction score 0
  • Comments 0
Installing the Morimoto XB (Oval) LED fog lights. Aiming the lights after the install. The center of the LED lights itself is at 28.5" inches from the

Installing the Morimoto XB (Oval) LED fog lights. Aiming the lights after the install. The center of the LED lights itself is at 28.5" inches from the

  • Media owner SidKo
  • Date added Jul 4, 2018
  • Reaction score 0
  • Comments 0
Installing the Morimoto XB (Oval) LED fog lights. After inserting the pins with the supplied connector, spread or pry the pins further apart so it can

Installing the Morimoto XB (Oval) LED fog lights. After inserting the pins with the supplied connector, spread or pry the pins further apart so it can

  • Media owner SidKo
  • Date added Jul 4, 2018
  • Reaction score 0
  • Comments 0
Installing the Morimoto XB (Oval) LED fog lights. Testing the polarity before using supplied connector.

Installing the Morimoto XB (Oval) LED fog lights. Testing the polarity before using supplied connector.

  • Media owner SidKo
  • Date added Jul 4, 2018
  • Reaction score 0
  • Comments 0

Members online

Total: 274 (members: 3, guests: 271)

Forum statistics

Threads
278,306
Messages
3,554,045
Members
248,016
Latest member
Advally Service

Share this page

Back
Top