Recent content by andynj

So I changed out the Charcoal canister and still can't fill the gas tank. I dont have any error codes and am starting to wonder if perhaps it is my gas gauge. Its showing 3/4 tank right now I guess I should get a container and run it dry and see what happens. What I might do is drive 20miles...

The blue thing is the light from the camera scope I put down the fill tube :) best tool ever btw!

I don't think its my gas guage because when filling fuel backs up into the fill tube and then very slowly goes down so there is room in the tank just very slow filling. I suspect a venting issue maybe a deformed vent hose and am going to drop the spare wheel and have a poke around this weekend...

2007 V6 100k miles no check engine light, no codes in OBD2. Last 2 times I tried to fill up at gas station pump stopped before a full tan, second time tried to force more in but filler neck filled up and overflowed on to ground. Seems like a venting issue but need help to diagnose whether...

Thats a good price especially from a dealer for this job, I did it last year on mine and had to buy some special tools to get the CV's out, while I was in there I drained and refilled the front diff too and the drain plug on that was a PITA to get out. I also had to replace the seal on the diff...

I was looking to do the same thing and splice the DD wiring to a plug that goes into the hitch harness on the T4R but the matching of the wires was a little ambiguous and when i plugged it iin I got a check engine light that I needed to clear. Let me know if you figure out the wiring color to...

I replaced my seat cover bottom with one off Amazon for my gray leather seats, color was a great match and it fit great. They are different from side to side though as there are cut outs below the plastic for the knobs and buttons on the side of the seat. You might be able to make a side to...

I looked at the install for a lot of different products when I researched remoted start for my 4th Gen. The Viper and another self install solution from Amazon looked tempting from the price and their descriptions made it sound really easy to install until you looked at the bare wire harness in...

New Projector lights solved it for me I had the same challenges as the OP in my 07 which has OEM projector housings. Mine were in perfect shape no dulling or yellowing but at any speeds about abvout 60mph you were outrunning the low beams and it was outright scare, I tried Auxbeam LEDS they...

I bought this bottom seat cover 4 years ago from Amazon, it says its not available anymore but you can prob find the company. I was $100 and is full leather. Color is really very close to OEM, probably exact when the leather was new you really can't tell. Fitting is OK figure on about 2...

i have considered upgrading but everytime I look the thought of spending the amount of money required for a new vehicle compared to the function, reliability and ease of maintenance of my 07 T4R the numbers just don't add up. Sure I would love ventilated, massaging seats, a digital dash...

Not the best pics, lights are pretty easy to install and wire. Halos come on with ignition, flash on indicators and turn off on low and high beams. They come with direct plugs for low and high beams so no splicing on those you just need to splice into the running lights for the Halos...

I tried upgrading my bulbs in an 07 SR5 as they were pretty terrible stock. I tried Auxbeams first and whilst bright I found on the high way and anything over 50mph I was outrunning the lights. I switched to DD SL2's which were expensive thinking it was the bulb but same thing - they were...

Haven't used these but I replaced the drivers side CV's twice due to torn boots and they were both neoprene ones. I would recommend getting one with plastic boots like OEM. The ones I posted above are much more heavy duty with hard plastic boots and about the same price. Also if only one boot...

You may have already done this but did you do the brake booster sequence to bleed it after the caliper was changed. I can't remember exactly but with ignition on but car off (I think) you need to press the brake like 8 times (?) it might then beep you press it a couple more times and its bled...