Recent content by Kryptoroxx

This is probably a bit late but I have one on a 4th gen v8. It isn't designed for a body lift but given the way that you cut the bumper I think a body lift wouldn't have an effect. Sent from my SM-F721U using Tapatalk

I replaced the ones on mine using a 1uz silicone kit but you have the v6. There might be a kit out there but there isn't anything wrong with the oem lines either. Sent from my SM-G986U using Tapatalk

This has been an absolute pita to get them to seal. I'm going to see if I can't make something like this. Where did you get the rubber pieces? I used the stocks and they fit reasonably well on the rx350 projectors in the back. Not so much for the d2s 5.0 projectors though. Very very clean...

A little bit of brush up work today. I touched up the front bumper and rear bumper along with fixing the platform the rear tire carrier sits on. This time I used plastic along with 3m mold tape. Then for the longest "fix" I put my home ec skills to good use and restitched some of my tire...

The designer for true North made a version 2. I'm trying to remember the name of his company. Alec Lueddecke is his name. He does mostly Facebook and is all over the groups there. I have the tnf rear bumper myself and it hauls just fine. It does have a hitch but isn't rated. Here's mine for...

110 is going to be your best fit for the 06+ headlights. Go with diode dynamics or mori for the halos. They've lasted me around 3 years I think. Sent from my SM-G986U using Tapatalk

You will need a 5 channel amp instead of a monoblock. There are a few that come in the stock size but once you have the amplifier in your speakers will likely blow very quickly. They do not take much power to run....and they aren't the greatest either.....but you're after just music. You'll...

So the dtrl is the 12 pin relay. It is a pretty big beast and you'll know immediately if you have it. I have it so I got the 12 to 6 pin adapter and an adjustable relay but ended up keeping the dtrl features and upgrading to led without hyper flash via other means. I have it laying in my...

I'm kinda looking at something like this too. I figure it's easier to replace them before they go. I have a bender, flare tool, and I've done a few small pieces on previous rigs. Never a whole system though. Is there a particular brake line that is more resistant to rust than others? That...

I'll be working on this for a few days but I'm eliminating vacuum line issues before they start like they did with my 3rd gen. I found a kit for 1uz silicone vacuum lines and I'm slowly going through and replacing them. Some are going to be a real mofo to do though. I see that a couple of mine...

I've got a few. Photography has been a hobby for many years. Currently shooting with a Sony a6600 and a small collection of primes and zooms. Currently it's a little easier to kit lenses with an apc than full frame financially but I've had a lot of fun with it anyway. Sent from my SM-G986U...

If you have a limited you can tap the circuit for the door lights that were on the running boards. Not sure if the wiring exists for other trims but if you tap that circuit it would have a nice fade out about 15 seconds later. Then it would just be a matter of adding a switch with a relay to...

Lol I had 2 quarts left from my transmission and thought it was perfect......till I looked it up. Oh well. I'll do it with the diffs and transfer case. Amsoil going in those though. Sent from my SM-G986U using Tapatalk

Swap the fluid. I just did mine yesterday. Really a simple process once you get the fluid. I stuck with the yota ws stuff however there are those that swear by x. If you have an external cooler it's even easier. I hooked up those lines in front of my truck and only had to slide under to...

[emoji1787] Sent from my SM-G986U using Tapatalk