Recent content by Lud

Sorry not eastern Carolina its Eastern industries Eastern 40364 Catalytic Converter $191. They also make a California compliant carb system for some more $$ but not to much --Lud

Heres all the big parts and numbers from amazon. This was for a 2002 4runner Walker 54681 Quiet-Flow Stainless Steel Muffler Assembly $114 :B0049J91H6 Walker 54081 Tail Pipe $67:B000C93E7K Walker 53616 Ultra EPA Certified Catalytic Converter $177: B001AGN71C (rear Cat) Walker 52399 Ultra EPA...

My cats were bad and the PO did a hack job to get a loud exhaust in. I redid the entire exhaust (2 cats, a walker quiet muffler, and tail pipe) with all the gaskets bolts and new hangers I got for just under 900. I think if I were to do a cat back it would have been around 200 bucks. I ordered...

So brought the truck back in for alignment and talked with a more experienced mechanics about hot to adjust caster and camber. We determined that i need to add 1 to the caster. He said he would have to charge me labor to make the adjust and so not willing to do that i brought it home jacked it...

So did the Zero calibration and it seemed to have fixed it. Was a ltle confused but figured it out. The diagram was reveresed from what was in mine but over all pretty easy. ill try the on ramp but trying to get it to go off i had no luck. still going to bring the truck in for an alignment since...

heres the print out so camber is still out on individual left. but the over all in the middle is good. --Lud

After the lift I had them align it and the caster was out. In Hawaii when you lift the vehicle your alignment has to be with in factory specs. That lead me to buy the LR UCA. order and got it installed. Went Back to get it aligned and they couldn't get the tie rod to move even though they did it...

Sure did. Measured about 4 times and the rear is all centered up. would that make the light come on during a turn? Ill measure it again on the truck and make sure it is the correct length.

Thanks for the responses. Im going to bring the truck back in the morning and see if one of the more experienced guys can get it. I figured with the new upper control arms it should be easy to align properly. Also I do have the print out at home ill snap a picture and upload it. While driving to...

Yes I got it aligned right after the lift. Goodyear I don't think did a good job so trying to find another company to get it aligned. Might have to drop it off again because for $110 and not being done right is annoying. How is Hot Lanta. I grew up in Marietta but haven't been back in about 10...

So I did a SS 1.2 lift on my 2002 4runner. I also did the LR upper control arms. Getting on the highway yesterday and today has a long right turn followed by a long left. Going about 35ish I get the traction control light on both turns Is this normal on a lifted 4Runner or is this a sign I...

Is that off of Nate Harrison Grade road? I use to take my KLR 650 up there all the time when I lived in SoCal. Absolutely beautiful views from up there. and you can get to the observatory without paying. --Lud

The PO did a hack job on the exhaust on mine and I had the same issue. I replaced both O2 sensors and it did not fix the problem. Ended up being that the CATS were bad. I bought new cats muffler and tail pipe with all the gaskets and hangars from amazon and it fixed the problem. Might need to...

Quick question, I was driving to work today and coming on the on ramp I got the traction control slipping signal I have the SS 1.2 lift and just finished the LR upper control arms. The on ramp has a pretty big curve and I was going about 35-40 around it when it came on. Is this normal or is...

So didn't do any work on the truck today but helped my friend work on his 1962 Ford F100. He got new wheels and tires and we painted to match his truck with the rim being red and the hub cap white. We also pulled off the old tie rod and Drag link. After putting all new pieces on we changed the...