Recent content by MannMade82

  1. M

    Oil change interval

    *Results may vary! I purchased my 2015 with 44k in 2017. Ever seen I have changed my own oil around the 10K mark. I always use Castrol Syntec and an OEM filter. I am at a little over 125K now but since 109K have been sending my oil to Blackstone for analysis. I am only two samples in (and one...
  2. M

    Looking into tires

    On my second set now. First was great. No issues at all...now I wish mine lasted 103k...closer to 50k for me before they were spinning in the rain. But I highly recommend them for daily driving and light off-road.
  3. M

    Purchasing Toyota Warranty

    Bought my wife a 2024 Highlander Platinum in June. I reached out to Troy for warranty quotes too. Much cheaper than the dealer offer. And can purchase anytime before the 3 year/36k mile mark. FD-Warranty
  4. M

    P2443 Code Still After Valve Replacement

    After changing spark plugs, my 2015 was throwing a P2443 code. So I found an OEM driver side secondary air injection valve on ebay and installed it. However, I am still getting the code at cold starts. Anyone else experience this and what was your course of action?
  5. M

    Should I replace the drive belt on my 2016 with 70k miles?

    Search on Amazon for: GEARWRENCH 15 Piece Ratcheting Serpentine Belt Tool Set | 3680D
  6. M

    Black transfer case dial knob

    :doh:
  7. M

    Mechanic I trust says I need to replace a frozen rear brake caliper, pad, rotor

    Not horrible if you aren't going to do-it-yourself. OEM Calipers are about $171 each online. $77 each for OEM rotors. $50 for quality pads (Akebono) and another $10 for a hardware kit. Then you'd have a labor...not sure how many hours their system shows. I'd consider a brake fluid flush/change...
  8. M

    Should I replace the drive belt on my 2016 with 70k miles?

    Just take your time and it isn't difficult to do. I used the Bando belt with the same part number printed on it as the OEM one. I also have this tool set, link below, and made it sooooo easy to replace: Amazon.com
  9. M

    Lifting the rear end 1" suggestions?

    How about Cornfed Suspensions 1" rear spacer?
  10. M

    Quick Tire Advice Request

    General ATX
  11. M

    Quietest AT Tires?

    General Grabber ATX. Super affordable, great traction, quiet, and look good too.
  12. M

    C4 Engine Bay Accessory Tray as ARB Single Compressor Mount

    Well it certainly fits without an issue. I have had it installed a week now and nothing hits. I did add a 45 degree elbow so the connection is level, but that's only my OCD, not a clearance issue.
  13. M

    C4 Engine Bay Accessory Tray as ARB Single Compressor Mount

    For those that are looking for an affordable ($25) mounting option for their ARB Single Compressor. Just need to drill new mounting holes and paint/coat. C4 ENGINE BAY ACCESSORY TRAY
  14. M

    C4 Fabrication Engine Bay Accessory Tray

    Anyone have a C4 Fabrication Engine Bay Accessory Tray? I have been trying to get the mounting surface dimensions but not getting a response from C4 or other retailers. I think it would make an affordable mount for a ARB single compressor at $25... Anyone?
  15. M

    Bilstein 5100 Height Settings

    I have had mine set at 1.75 with rear 1" Cornfed spacers for almost two years and I have zero complaints. Just get it aligned after the install. I installed them myself, solo...not hard to do if you are handy and have tools.

Members online

No members online now.

Forum statistics

Threads
278,493
Messages
3,551,631
Members
248,193
Latest member
erinobr2000
Back
Top