Recent content by power818

I am looking to get a roof rack for my 2019 4Runner. Unfortunately, the fit into my garage is tight. I have right around 4.5" of clearance above my roof into the garage door after my lift and 285 tires. That being said, I wanted to see what roof racks you guys recommend that are very tight to...

Install I got a set of 285/70/17 KO2's installed yesterday. They only rub in one spot on the driver's side mud flap at full lockout. I won't even have to take the mud flaps off. They barely touch, so I can probably zip tie the mud flap to hold it tighter to the body mount, and it won't touch at...

That's what I like to hear.

I installed Bilstein 5100's all the way around with stock coils. I set the front shock to 2.5", and in the rear, I went with the 1.5" daystar spacer. I did a full write up on it if you are interested. Bilstein 5100 2.5" Front and Daystar 1.5" Rear Spacer Write-up I personally felt like this...

This was not the case for me. I am at 2.5/1.5 with the Bilstein 5100 setup and had no issues getting proper alignment.

I am running stock UCA's and still want to fit the 285's. Do you have any knowledge to rubbing on the body mount and other locations with the 2.5/1.5 lift?

I have honestly never even used my 4WD, so I definitely am not a hardcore rock crusher. I know that it can make a difference measuring from the ground by wheels and tire selection. I am measuring with the Pro wheels and the stock tires which only have about 7k miles on them. Do you have...

I know this question has been asked before, but I have searched high and low and cannot find a good answer. I am running the TRD Pro Sema Wheels that have 4mm (3/16") offset and 93mm (3 11/16") backspace. I lifted my 4Runner with 5100's set at 2.5" in the front and a 1.5" daystar rear spacer...

I uploaded it to Flickr. I use it to upload pictures to posts, but I have not been able to make that work.

I recently replaced my OEM shocks with Bilstein 5100's and am looking to get rid of my take-offs. They have around 3500 miles on them. They came off of my 2019 SR5, and they have never seen anything but pavement. I haven't even had my vehicle in 4WD yet.

I'm beginning to get a little stir crazy during this lockdown, and I am looking for some inexpensive projects or modifications I can do. What have you guys been doing to your vehicles? Here's a list of the modifications I have made thus far: New wheels Running boards Blackout emblem kit Blacked...

I am trying to add a signature picture to my account, but I am having issues with this adding. I have tried to upload an image from my computer, and I have tried to add with a URL. Neither will work. When I upload from my computer, after clicking upload, the page reloads and nothing happens...

I used Bilstein 5100's front and rear. I got them for $372 out the door from Total Automotive Performance and received them in less than 48 hours to Alabama. Got the spacers for $35 from Amazon, so the entire build was under $400 total. And yea, I definitely should have taken pictures along the...

It is hard to tell what it is on the paint. I would give it a step-by-step approach going up in aggressiveness until you figure out what works. If you have already washed it, try cleaning it with full strength (undiluted) SuperClean Degreaser or really any degreaser will work. Give the degreaser...

I recommend Meguiar's Gold Class Leather Cleaner and the Leather Conditioner. I do detailing work on the side, and I have never had a seat that they didn't penetrate. If a seat is very dirty; however, I will clean it with a 1/5 dilution of SuperClean Degreaser before conditioning it. I do have a...