5th Gen For Sale/Wanted Thread

[Mutant138]

AZ locals parts sale

Arizona parts sale

Pedal Commander PC27 *NON Bluetooth* 5th Gen 4Runner ‘10+

$250

Had it on my truck for a year or two. Really like it. Definitely makes the truck more spirited by taking the slack out of the pedal and shift points. Want to put the money towards steel bumpers, winch, and new springs to compensate.

Vehicle Fitment:

10+4Runner
Possibly other Toyota Lexus models (GX, Sequoia, Land Cruiser, Tundra) buyers responsibility to do their research. Don’t think it will work with Tacoma’s.

PC27 - Pedal Commander Throttle Response Controller *NON Bluetooth* older model.



4Runner Tacoma FJ TRD OR Wheels *hobbyist special*

185

Originally bedlined. Looked good for two years or so.

One wheel has some trail rash. No centercaps.

Sand blasting and powder coating should cost you 3-400 bucks. Then you will have yourself some one off trd wheels.

The lips are reinforced, valve stems recessed, and they are lightweight making them an excellent choice for off-roading. Only swapped them out because they did not clear my specific upper control arm choice when I lifted. Was going to repaint them for another two years of service. Taking up too much room and I have too many other projects. My loss your gain.

17x7.5
6x5.5

Priced accordingly but open to reasonable offers.




DOBINSONS REAR OFFSET HEIGHT KDSS COIL SPRINGS FOR TOYOTA 4RUNNER AND FJ CRUISER 35MM LIFT (C59-723)

$125

Had them on my new model 4Runner for 2 or 3 months before opting for a lower lift.

Here is the selection of KDSS-specific rear coils. Suits these models:

Toyota 4Runner 2003 to 2009 4th Gen

Toyota 4Runner 2010 to 2019 5th Gen

Toyota FJ Cruiser 2006-2015

Lexus GX460

Lexus GX470

Rear Coil Options, with KDSS. **Or for vehicles with a leaning issue and want to offset the height

Our KDSS coils are 15mm taller on one side to go onto the US passenger side (right side) to compensate for vehicle lean

C59-723 – Stock rear end, 1.25″ to 1.5″ lift, offset height coils for KDSS leveling. 420/405mm, 17mm wire, 228LB rate

 

[Landosboost]

Victory Full length roof rack $850 pickup in Syracuse NY

2019 Victory Roof Rack 4runner 2010-2020 - auto parts - by owner -...


Thanks

 

[Mudhorn]

Red Steering Wheel Emblem
$25 shipped

Made by Jimmy Rigged on Etsy

Never opened, saving you on shipping and tax

Fuse Box Cover SOLD

Fuse Box cover $15 shipped

 

[BEAR x SF]

Factory flawed USR Tail lights, glued one side but left the other alone. Could be fixed with your choice of sealant, only visible when trunk hatch is open but when it's closed you wouldn't know it's there. Still in their original packaging. Looking to sell locally, based in San Francisco but will ship at buyers expense if I don't have a local buyer. Other than the flaws they're basically brand new. Looking for $200 but will hear out offers but I won't respond to lowballs.

Also have a driver side stock tail light. Taken off after 1,000 miles. Asking for $75 but willing to hear out offers.

Bump!

Knocking the price from $200 to $175 and the driver stock tail light from $75 to $50

 

[Ry'sRunner]

2020 TRD PRO roof rack for sale in San Diego. $500. Will be available by next weekend when I swap for a Gobi. 1600 miles in, basically like new, never carried anything on it.

 

[ElectroBoy]

VLEDS Reverse Backup LED 921 bulbs - $35 - San Jose CA

Edit: SOLD

For sale: Two VLED 921 bulbs for the reverse lights on a 5th Gen 4R. They work great, much brighter than the stock incandescent bulbs and a nice white color (5000K). Rated 850 lumens each. I used them for about two months then got a different brand of LED bulb.

They are currently $35 each from VLEDS. I will sell them to you for half price, $35 for two bulbs. Shipping included. Payment via PayPal.

VLED website:
HIGH OUTPUT WHITE 6 LED 921 - 921 - Reverse Back-Up - Shop By Application

 

[Chevrolegs]

I have the stock suspension off of my 2020 trd off road. Removed at 5750 miles. Nothing wrong with it, took it off and installed the eibach kit.

Located in Orange County.

$100

 

[SHagood]

OEM side rails and cross members taken off a 2018 ORP, excellent condition.

Located in Tampa, will ship at buyer's expense. Asking $100.

Price drop to $100, will ship.

 

[Padres86]

Been a while weeeee, but what are you getting/got next?

I'm sad to see her go, but it's time to move on.

For those of you who've been following me, we've done a lot of adventures on this rig, and it's performed flawlessly both on and off road. But it's time for the next big adventure, which means eventually moving to another platform. I'm not in a rush to sell, so I'd love for someone to appreciate the hard work that's been put in this.

Truck will be professionally detailed and maintenance (including spark plugs, oil change, transfer case/diff fluids) will be performed before the new owner takes the keys. Pretty much all major maintenance to the suspension components and brakes were done within the last 30 days.

2015 Toyota 4Runner TRD Pro
91,xxx miles
One owner (two, if you count the wife)

Mostly complete list of mods:

Exterior
McQueen fenders w/ snorkel cutout
Eezi-Awn K9 2.2M Rack w/ 40mm legs
RAV4 Blind Spot Mirrors
ARB 2000mm Awning (will include awning room)
Satin Black 3M 1080 Roof Wrap

Armor/Recovery
Shrockworks Front Plate Bumper
BAMF Bolt-on Rock Sliders
RCI Full Underbody Skids
CBI Rear Bumper- Dual Swing Out, modified to hold propane and Maxtrax
Warn M8000 Synethetic
Factor 55 Flatlink/1" Fairlead

Engine
TRD Cold Air Intake
ARB Safari Snorkel

Interior
Custom cargo platform with rear seat deletes (rear seats can be swapped in/out independently)
Dual USB plug in center console
Red/white switchable LED Interior Lighting
Husky Weatherbeaters
Molle window panel

Brakes
Stoptech Slotted Rotors (changed last month)
EBC Yellow pads (changed last month)

Electrical/Lighting
40" Rigid Pro Single LED Light Bar on roof rack
Rigid Ignite Rock Lighting x 4
2x Rigid SRQ Pro on side of rack
2x Rigid SRQ Amber on rear rack (amber trail flashers)
Xenon Depot HID kit w/ Philips 4300k bulb upgrade
Odyssey Group 25 Battery
National Luna Single Battery Monitor
Bussman Relay Box w/ OTTRATTW Switches in center console
ARB Twin Compressor OBA system w/ ARB 1gal tank
Blue Sea fuse panel in rear cargo
Blue Sea HD Disconnect for winch

Suspension/Wheels
King 2.5 Extended Travel fronts w/ CDC adjusters and 700# springs- rebuilt this month
King 2.5 rear shocks w/ CDC adjusters- need service soon
Total Chaos UCAs- rebuilt this month
Icon Overland rear coil springs
Timbren Active Off Road Bumpstops rear
Wheelers Bumpstop Fronts
SCS Ray 10 17x9.5
Nitto Ridge Grapplers 305/70/17 (34x12.5)

I'm sure I'm forgetting something, but please PM for any questions. Asking $45K, located in the Bay Area.

Tent, fridge, comms, and recovery gear are NOT included- otherwise this is a complete turnkey vehicle build.

 

[Padres86]

***NEW*** Icon billet lower trailing arm kit for 5th gen 4Runner - Jax Bch,FL

Selling brand new in box Icon billet lower trailing arm kit for 5th gen 4Runner. $650 (MSRP $787.45). PM me if interested.

 

[Padres86]

***NEW*** (4) Spidertrax 1.25" Spacers for 5th gen 4Runner - Jax Bch,FL $200

Selling a set of (4) brand new Spidertrax 1.25" blue spacers (WHS007) for 5th gen 4Runner - Jax Bch,FL $200

 

[sn_85]

Been a while weeeee, but what are you getting/got next?

AFAIK he kept it. Haven't seen any new rigs on his IG. He definitely has a beautiful build though!!!

 

[Padres86]

AFAIK he kept it. Haven't seen any new rigs on his IG. He definitely has a beautiful build though!!!

Thanks

 

[ForRun]

SOLD - Lexus LED Fogs

That was fast, these sold in less than 1/2 hr
These run $225 new. Had them on the runner a couple months, hardly used thanks to covid. Starting to black out my runner. Build quality is much better than the runner oem led and they are perfect fit.
$150 firm, Shipped to lower 48

 

[shrub1]

Baja Designs Squadron Pro R driving light/combo pattern

A Pair of Baja Designs Squadron R Pro driving light/combo pattern.
Includes Baja Designs wire harness and switch.
Like new, turned on once while parked in the garage. That's it! Zero nicks or scratches.
$250.00
Would prefer local pick up or will meet half way in Orange County CA.

 

[ForRun]

VALANCES SOLD will re-list grill top section
Front and rear valances and top of front grill.

These came off 20orp with ~1500 miles. Front valance is drilled for plate.
$120 shipped for Valances
Make an offer for grill. You can get it blacked out and only need to pull yours out one time

 

[ForRun]

2020 Orp suspension
Taken off ~1500 miles.
100 plus shipping from 60008.
No I'm not dragging these to UPS or fed ex to price.

 

[krhayes79]

TRDOP Carpet Mats

I have a full set of TRD Offroad carpet mats in gray that have never been used and still in the plastic.

PM if interested.

 

[Berty_K]

Rear Differential Breather Relocate Kit, $40, Free Shipping

I’m selling a rear differential breather kit for our trucks. This kit relocates the breather into the engine bay near the other breathers. There are two reasons you would want to do this:

1. You drive in deep water: if you’re on a trail and your rear differential becomes submerged, the sudden cooling of the differential causes the pressure in the housing to drop. Water gets sucked into your housing, mixes with the gear oil, and damages your differential.
2. Your breather doesn’t work anymore: If you have an old or rusted breather, there’s a good chance it is no longer working. If the breather can’t release pressure and oil gets pushed out of the differential seals, causing premature wear.

This is a “beginner friendly” DIY, so no need to be intimidated! My instructions (provided here) will walk you through the entire process from start to finish. I’ll also provide my contact information for you to reach out if any issues come up.

Kit cost is $40 shipped anywhere in the US. Payment via Paypal, Venmo, or Zelle. All components are manufactured in the USA and are high quality.

• 15 feet low pressure fuel line
• 1 male brass barb (Threads into rear differential)
• Breather assembly (90 micron nickel-plated steel breather and female brass barb, assembled with teflon tape)
• 2 stainless steel worm drive clamps
• 1 galvanized steel loop clamp
• M6 locknut
• 10 zip ties
• Instructions (also attached to this post)

Items you will need:

• 14 mm wrench or deep socket
• 10 mm wrench or socket
• ½ inch wrench or crescent wrench
• Snips or scissors
• (Optional) PB Blaster/penetrant
• (Optional) Jack, Jack stand, Wheel Chocks

Compatible vehicles:

• 3rd, 4th, 5th gen 4Runner rear differential
• FJ Cruiser rear differential

Instructions:

 

[weeeee]

Been a while weeeee, but what are you getting/got next?

AFAIK he kept it. Haven't seen any new rigs on his IG. He definitely has a beautiful build though!!!

Oh man, not every day that I go on here but glad I caught you guys. I haven't been very active on here or IG. I definitely need to get out and camp more!

I wanted to get into a GX460 or a 70-series LC Troopy last year a couple years ago but officially listed it for sale late last year. Ultimately I got cold feet and pulled the sale since just didn't make much sense to try to rebuild something that I've already dialed in. The 4Runner is awesome but sometimes I just wish it wasn't so underpowered. Other than that it's been great.