FS: Fuel Savage wheels/Nitto Terra Grappler G2's. $1350, Kathleen GA.

[Paragon1]

FS: Fuel Savage wheels/Nitto Terra Grappler G2's. $1225 Kathleen, GA

20x9, +1 offset, so they're flush with the fender. Only 13K on them. Nothing wrong with them at all, I'm just going for more aggressive setup. Let me know if you have any questions. $1225 firm.

http://www.toyota-4runner.org/5th-gen-t4rs/200959-wheels.html

 

[Paragon1]

bump

 

[Paragon1]

bump

 

[JRZ4runner]

Did you have to life your 4runner to make these fit with out rubbing? Are they the all black ones?

 

[Paragon1]

Did you have to life your 4runner to make these fit with out rubbing? Are they the all black ones?

If you're running the stock height, you will get a little rubbing while in reverse with the wheel turned to full lock. You don't necessarily have to lift it though, you can trim the fender liner to accommodate the wider wheel. The reason it didn't rub too bad is the offset of these wheels is +1 instead of -12 (which is wider).

I ran stock height for about a month before going through with my pre-planned lift (1.25 in on blisteins). It was never an annoyance. In fact, I'm wishing i only did the .8 lift as i prefer the raked look like i had with my last one.

They are the black ones with the black lip. However i removed and polished each of the 100 bolts around the perimeter of the lip.

 

[JRZ4runner]

I wish

If you're running the stock height, you will get a little rubbing while in reverse with the wheel turned to full lock. You don't necessarily have to lift it though, you can trim the fender liner to accommodate the wider wheel. The reason it didn't rub too bad is the offset of these wheels is +1 instead of -12 (which is wider).

I ran stock height for about a month before going through with my pre-planned lift (1.25 in on blisteins). It was never an annoyance. In fact, I'm wishing i only did the .8 lift as i prefer the raked look like i had with my last one.

They are the black ones with the black lip. However i removed and polished each of the 100 bolts around the perimeter of the lip.

If I lived a little bit closer I would definitely take them off of your hands, but the 10+ hour drive just puts them out of my price range.
Good luck selling them.

 

[Paragon1]

he bumps the ad to the top again...

 

[Paragon1]

Bump

 

[RikiTiki]

These are available in Kathleen Ga correct? My brother lives there , my wife and I are coming through Tuesday this week . the slight rubbing does concern me) as her 4R is not lifting or spaced but I think either way I'll take em and adjust later Let me know what your schedule looks like

 

[bryantd85]

Your signature says you're in Melbourne Fl, that's where I am! Did you move up to GA?

 

[Paragon1]

These are available in Kathleen Ga correct? My brother lives there , my wife and I are coming through Tuesday this week . the slight rubbing does concern me) as her 4R is not lifting or spaced but I think either way I'll take em and adjust later Let me know what your schedule looks like

Yeah they're in Kathleen, but I'm deployed at the moment and won't get back until the middle of next week. Also, still have to order my new set! Just trying to make sure I have a buyer first.

 

[RikiTiki]

Roger that, just let me know when you're back in town (pm me) my brother could pick me for me. Thx

 

[bay_area4runner]

Are these still available

 

[Paragon1]

bump

 

[Paragon1]

Are these still available

yes, however the price in the original ad was incorrect apparently due to my inability to use a computer properly. $1350 firm.

 

[Paragon1]

Your signature says you're in Melbourne Fl, that's where I am! Did you move up to GA?

Yeah I was living there for a while but just moved back to Georgia. Headed to Melbourne today though.

 

[Paragon1]

Bump

 

[Paragon1]

Bump

 

[Paragon1]

bump

 

[Paragon1]

Bump