Installed. notice the extra light in the reflector, this is from the projector not being sealed, you can use foil tape to seal the holes where light m

Installed. notice the extra light in the reflector, this is from the projector not being sealed, you can use foil tape to seal the holes where light m

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
Once youve adjusted the aim of your projector go ahead and replace the glass covers onto the reflectors, if you are completely done, Jb weld the screw

Once youve adjusted the aim of your projector go ahead and replace the glass covers onto the reflectors, if you are completely done, Jb weld the screw

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 2
check out that cool cutoff.

check out that cool cutoff.

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
Notice how the beams are aligned and level.

Notice how the beams are aligned and level.

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
the cutoff color gets more vibrant from a farther distance.

the cutoff color gets more vibrant from a farther distance.

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
now as you can see both beams are level but they are not the same height, if you set the reflector adjusters at the same level you can use the mountin

now as you can see both beams are level but they are not the same height, if you set the reflector adjusters at the same level you can use the mountin

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
Now this is the important part, once youve mounted your projectors you want to align the bulb so its sitting in the same spot that the old halogen bul

Now this is the important part, once youve mounted your projectors you want to align the bulb so its sitting in the same spot that the old halogen bul

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
Projectors fitted in both reflectors

Projectors fitted in both reflectors

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
after mounting the projector I attached the reflector, without the glass back onto the mount.

after mounting the projector I attached the reflector, without the glass back onto the mount.

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
After I drilled the holes in the reflector I mounted it, I used 6 32 2" screws When I take it apart again Im going to use some nicer m4 cap nut screws

After I drilled the holes in the reflector I mounted it, I used 6 32 2" screws When I take it apart again Im going to use some nicer m4 cap nut screws

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
The two white plastic pieces adjust the angle of the headlamps. In my opinion you should align you projector coaxially with the bore of the thing stic

The two white plastic pieces adjust the angle of the headlamps. In my opinion you should align you projector coaxially with the bore of the thing stic

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
You can Ziptie and tape the bubble wrap over the lense to protect it while you assemble the headlight, also you can stick the bulbs in to keep dust pa

You can Ziptie and tape the bubble wrap over the lense to protect it while you assemble the headlight, also you can stick the bulbs in to keep dust pa

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
I put blue tape over the glue on the edge so the plastic dust wouldnt get into it.

I put blue tape over the glue on the edge so the plastic dust wouldnt get into it.

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
Dremeled out the back of the reflector.

Dremeled out the back of the reflector.

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
Reflector with glass and center piece removed I used a heat gun on edge and a razor blade then a wide chisel to pry it open, Sort of a pain but Once

Reflector with glass and center piece removed I used a heat gun on edge and a razor blade then a wide chisel to pry it open, Sort of a pain but Once

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
This is the back of the reflector

This is the back of the reflector

  • Media owner D Farms
  • Date added Mar 1, 2014
  • Reaction score 0
  • Comments 0
D Farms

3rd Gen FXR-3.0 Retrofit

  • Items 16
  • Album owner D Farms
  • Date created
There are no comments to display.

Album information

Album owner
D Farms
Date created
Item count
16
View count
0
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

D Farms

D Farms

Media items
57
Albums
4
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Members online

Total: 3,274 (members: 4, guests: 3,270)

Forum statistics

Threads
278,316
Messages
3,554,124
Members
248,016
Latest member
Advally Service

Share this page

Back
Top