Media added by K5to4R

Navigation

Browse albums

Trending media

final product. coffee table has a cut out for a tumbler and workspace. The right drawer has a simple cover to serve as a table / makeshift changing st

final product. coffee table has a cut out for a tumbler and workspace. The right drawer has a simple cover to serve as a table / makeshift changing st

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Test fit of equipment. This load out will change once I mount a roof rack and throw a box on top to house recovery gear. Plenty of room for mechanic

Test fit of equipment. This load out will change once I mount a roof rack and throw a box on top to house recovery gear. Plenty of room for mechanic

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Decided to added a 'coffee table' spring pop up to one drawer. Because of the compression locks, I had to space the pop up to give it clearance, and

Decided to added a 'coffee table' spring pop up to one drawer. Because of the compression locks, I had to space the pop up to give it clearance, and

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
2 coats of black stain and 2 coats of poly, love the dark look. I used carriage bolts on the outside (1 inch) with jam nuts in the drawer recess. I

2 coats of black stain and 2 coats of poly, love the dark look. I used carriage bolts on the outside (1 inch) with jam nuts in the drawer recess. I

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
I opted to use framing L brackets to mount the drawer system. I like this as it s strong than turnbuckles but I can still remove the drawer if needed

I opted to use framing L brackets to mount the drawer system. I like this as it s strong than turnbuckles but I can still remove the drawer if needed

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Taped off the drawer front to prevent splintering when cutting. 3/4 blatic on front of 1/2 drawers for strength and depth.

Taped off the drawer front to prevent splintering when cutting. 3/4 blatic on front of 1/2 drawers for strength and depth.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Final drawer front aligned and braced for cut. Once cut, i glued and secured after final test fit in drawer

Final drawer front aligned and braced for cut. Once cut, i glued and secured after final test fit in drawer

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Built a mock drawer front to practice before the final product, huge help as it allowed me to shift and adjust spacing

Built a mock drawer front to practice before the final product, huge help as it allowed me to shift and adjust spacing

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
measuring depth of the compression latch

measuring depth of the compression latch

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
measurement for bracket to allow compression latch to secure to top of drawer.

measurement for bracket to allow compression latch to secure to top of drawer.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
simple drawers with 1/2 inch baltic all around. No fancy joints here.

simple drawers with 1/2 inch baltic all around. No fancy joints here.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
measuring and bracing the divider. If I did this again, I would cut pieces of wood to use to brace where drawers go and ensure even fit.

measuring and bracing the divider. If I did this again, I would cut pieces of wood to use to brace where drawers go and ensure even fit.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
My first shot at pocket holes. This was to hold the sides, back and center in place. Eventually used screws and glue to firmly secure and ensure I h

My first shot at pocket holes. This was to hold the sides, back and center in place. Eventually used screws and glue to firmly secure and ensure I h

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0

Members online

No members online now.
Total: 8,674 (members: 0, guests: 8,674)

Forum statistics

Threads
278,440
Messages
3,551,251
Members
248,149
Latest member
044runner4

Share this page

Back
Top