Recent content by fastgtfairlane

I did bleed the porportioning valve. Still no fluid moving to the rear wheel cylinders. Bled the front as well. There was some air in there in the front and at the valve. Still no flow at the rear cylinders. Also opened the line coming from the valve to the rear circuit. It was also dry. So...

94 4runner sr5 3.0 5spd 4x4 298k miles Had to replace both rear axle bearings and seals recently. Had axles out for several days. Used rubber vacuum cap over brake lines during that time. After putting it all back together I have no fluid to rear wheel cylinders when attempting to bleed them...

Bought my 94 3.0 4x4 5spd about 5 years ago with 200k on it. I'm at 298k now. Engine still runs fairly well. It does leak and burn a little oil. To my knowledge the head gasket recall had been done before I bought it. It doesnt run hot. I did have the timing belt go out on me at like 260-270k...

Update. So after further investigations from driving, I've noticed the ac blows cold while driving at highway speeds but heats up and shuts off basically at a stop light. After driving home from work today and opening the hood with the vehicle running, I noticed the small condenser fan motor...

cool deal ill have to check that out. hard to tell without gauges what its really doing but it doesnt act like a refrigerant issue but more like a mechanical issue or electrical

the rear most window on my truck has come off the track. the plastic rollers have broken. anyone have any suggestions where to find the plastic rollers that goes in the window track?

got a 94 4runner 3.0. had the vehicle for several years. ac has always blown very cold. few days ago as im driving into work (about 30 min from home) i noticed the air temp coming out of the vents was warm. green ac light still lit. go to leave work and ac blows cold the entire time. this has...

i had what sounds like a similar issue with my 94 runner. i didnt have the drain and fill plug issue though. i thought it might be a bearing in the pinion or ring gear but ended up being absolutely shot axle bearings instead. removed the 3rd member to find no isssues. when i drained the fluid it...

ok cool i will have to try that very soon. ive gotten good at getting the door panel off and back on. kick panel should be much easier. sounds like that is where the problem exists. i figured there might be a common area to check.

looking at the design of the stock exhaust setup, you would think headers would really free up the exhaust flow getting rid of that crossover tube. if its too loud with headers, you could always run a resonator and a muffler to quiet it down. also the muffler choice will have a lot to do with...

passenger front window on my 94 4runner will power roll down but not up. i have replaced the window motor/ regulator assembly, as well as the driver window switch assembly and passenger window switch. if i use jumpers and reverse the two wires at the window motor and push the window button down...

cool thanks for the picture. according to that my truck has every option on it except for the sport package and auto trans. leather, sunroof, ac, rear heat, 31x10.50s, running boards, roof rack, premium radio with 6 speakers, cruise, and power package. shes been rode hard and put up wet. still...

So I finally got the axle bearings, seals, and brake shoes replaced yesterday. both bearings were worn slap out, the driver side brake assembly was full of gear oil when i pulled it apart. luckily for me, i have a buddy that builds auto trannys for a living and we did the work at his shop. made...

thats perfect exactly what i was looking for and pretty good pricing considering it includes the seals, retainer, bearing and c clip. im still not sure if the 3rd member is bad or not as i havent pulled it apart yet. i feel pretty confident the noise is coming from the right rear wheel bearing...

my 94 4runner has a rear end sqawk which sounds like a rear axle bearing. the gear oil was drained and refilled. water was found in the housing from backing the truck in the water to load and unload my jetski with a hitch hauler. the axle bearings felt bad with the wheels off. i was wanting to...