Recent content by mountainman_gz

fishrod, haha well, in 1988 they didn't have indicator lights. I will try your milk container idea. There's only one way to find out, right?

So related question, I have an '88 V6 and my manual says my tank is about 17 gallons (65 Liters) BUT the needle on my truck is on the bottom part of Empty at 15 gallons (55 Liters). With this difference, I can drive another 60-90 Km or 36-54 miles. I haven't been "out of gas" yet. Has...

And Voila! <a href="http://s37.photobucket.com/albums/e54/getshynx/?action=view&current=PA260050.jpg" target="_blank"><img src="http://i37.photobucket.com/albums/e54/getshynx/PA260050.jpg" border="0" alt="Photobucket"></a>

Done and done Hey, I'm finally finished the 4runner. Take a look: <a href="http://s37.photobucket.com/albums/e54/getshynx/?action=view&current=PA250010.jpg" target="_blank"><img src="http://i37.photobucket.com/albums/e54/getshynx/PA250010.jpg" border="0" alt="Photobucket"></a> <a...

Would it be some type of air-flow system so that it dries off any moisture in the panel? I have no idea...

94Beast4Runner: I totally lazy and didn't care to take the emblems off. It was early in the morning haha. In light, if you look really closely, you can tell. But so far no one has noticed :D I didn't blast it. There was minimal rust in the front end probably due to past oil leaks which have...

Hey, So I was cutting my 4runner apart when! I found a hose at the bottom of the rocker panel. Weird. So I blew air into it and found that it comes out the top vents. What the hell is this tube for? WHy would there be a hose that goes to the rocker panel? WOuldnt they want the water to bead...

<a href="http://s37.photobucket.com/albums/e54/getshynx/?action=view&current=P9120065.jpg" target="_blank"><img src="http://i37.photobucket.com/albums/e54/getshynx/P9120065.jpg" border="0" alt="Photobucket"></a> <a...

<a href="http://s37.photobucket.com/albums/e54/getshynx/?action=view&current=P8290017.jpg" target="_blank"><img src="http://i37.photobucket.com/albums/e54/getshynx/P8290017.jpg" border="0" alt="Photobucket"></a> <a...

So I haven't replied in awhile, I've been busy (Not with the runner) I'm going to finish this baby off in the next few weeks There are a lot of pictures but they show the work Enjoy! Before: <a href="http://s37.photobucket.com/albums/e54/getshynx/?action=view&current=P8270042_2.jpg"...

Checked it out, the frame is pretty good. Most likely due to our dry climate. Had some problems with bushwacker so I'm going to make my own fenders :S we'll see how that goes. I triple coated the frame with a asphalt spray <a...

I inspected the frame today and took a grinder to the rust. It was superficial, nothing too bad. I coated it afterward. I'm planning on putting 3 coats on. That wheel well is by far the worst one. Other than Bushwacker, what else would work around there?

Hey again, I have some pics illustrating what I mean <a href="http://s952.photobucket.com/albums/ae3/mountainman_gz/?action=view&current=P8170031.jpg" target="_blank"><img src="http://i952.photobucket.com/albums/ae3/mountainman_gz/P8170031.jpg" border="0" alt="Photobucket"></a> <a...

Hey everyone, I was planning on cutting most of my wheel well out of the front and back due to rust. So there would be no fender overhang. I was wondering if bushwacker fenders would look ok? I was told they're made for if you cut out about 3 inches of material from the wheel well. I'm...

Hey, Ok, I'll give a whirl. Thanks