Recent content by ViaPhoenix

It has definitely finished the test cycle, but even before the misfire was fairly noticeable, and previously clearing of the codes it would be back before ever leaving park. Still only at 30-40 miles tho, (only 6 miles RT to work each day). Any guidance for looking at live data? link to...

I am using Toyota plugs from my local dealership. I replaced my TPS sensor (I have been getting codes for this) and swap coil pack 3 and 5 yesterday. I let it idle for 20-30 minutes in my drive way then drove 1 mile or so yesterday and then to work today (~10 miles Round trip)...no codes so...

thanks, what about porcelain/collar above the crush washer discoloring, normal?

yeah i am on a path, i just tried googling spark plug condition NGK and other sources, but i didnt seem to be able match mine to their images. step 1 swap spark plug step 2 swap coil packs step 3 cylinder compression test step 4 carb cleaner through fuel injectors step 5 replace spark plug...

Hello Tshooting a cyliner 2 misfire. So far i have just replaced the cylinder 2 spark plug, no change. My first look i felt it looked normal, but wanted to bounce it off some of you all as well to check. The gaps are a little big, i can get the .045 on one side and .050 on the other

I did order online, but it was suppose to be OEM, but the internet is a lair, sometimes. Co-worked mentioned the TPS being off could have leaned out the fuel. I guess i will load the parts cannon for the TPS. As far as the misfire, these are the steps i am going to take, thoughts? Also, so...

I couple year back I got the TPS code, and just cleared the code and it stayed off, but after a few months i still loaded the parts cannon that change the TPS. Recently about 2 months ago i started driving my 97 around again after sitting for a while (completely dead battery) and the code...

Finally swapped in the manual hubs, new OEM seals and bearing, replaced the UCA with a JBA UCA, and got it aligned.

Hey! Just upgraded to a set of 7.5 Wraps to correct a rear sag after adding a lot of weight to my rear. I installed them in Mar '21 and probably only put 1000-1500 miles on them. I would obviously prefer a local buyer, but will figure out how to ship if you pay for the shipping.

Swapped out my OME 890's for LC80 7.5 wraps (Toyo part# 48131-6A480), so much happier with how it leveled out the T4R. I got 1 3/4" lift at the tire and ~3" for the rear bumper. Also, I have a set of OME 890's for sale now :) ~1500 miles on them. Thanks so much Bad Luck and RomanSchnobrich...

I started with this link and like 14 tabs later i found myself on my link with the Toyo Part numbers. I will prolly put a WTB out there and see what i find, but good to know the part numbers in case nothing turns up. Not sure why, but i always thought i need to get a driver/pass pair from...

Thanks! I had forgotten about those options from my original research, but I remember feeling that sourcing the 7.5 wraps was going to be tough, since no one seemed to have a part number and I've never see an LC in the junk yards here in PHX. I think I just found on a ih8mud thread -Link-...

In the last couple weeks, I have done the washer fluid bottle relocate mode, replaced the spray nozzles with the Honda Odyssey sprayers from a couple pages back, and got my CBI re bumper mounted on finally (it arrived while i was on vacation in September). Full Res photos, and videos from the...

Sorry if this doesn't belong here, but at least half the post is detail the work i did to clean up a family friend's 4runner that he has owned since 1998 that had seen better days. I wish I took before photos on the interior. I have spent the last 4 months fixing up a 97 SR5 5Spd for my dad...

...8 Months later... Alright, update time!! My dad took Title of this in Late August, and i have been working on it when I can since and we are finally ready to put it on the market. I have taken 4 weeks of vacation and worked on my own 4runner some, so it lead to taking a while to clean up...