Exhaust Tip Installed

Here's mine.
 

Attachments

  • image.jpg
    image.jpg
    135.5 KB · Views: 5,086
Sorry to revive an old thread. Just tried to install my exhaust and it will not even slide on the muffler pipe. Do I need to spread it out ?
 
Well I feel stupid...this tip doesn't fit my factory tailpipe. Part #PT932-89100. Says fits all 2010 and up 4R's. Mine is a '14 Trail Premium and the pipe is oval shaped. No way this tip will go on unless I bend it all to hell.
 
Yup - our 2013 SR5 came with that tip and the rack crossbars too. Maybe it's another area thing; or standard dealer order thing.
 
Thesoundofpanic9 said:
Well I feel stupid...this tip doesn't fit my factory tailpipe. Part #PT932-89100. Says fits all 2010 and up 4R's. Mine is a '14 Trail Premium and the pipe is oval shaped. No way this tip will go on unless I bend it all to hell.
Click to expand...

Why would you need to bend it?
Did yours come with the 2 inserts and the clamp?

If so, it will fit.
 
Saker said:
Why would you need to bend it?
Did yours come with the 2 inserts and the clamp?

If so, it will fit.
Click to expand...

My tailpipe is shaped like an egg and the exhaust tip is round. I would need to bend the exhaust tip to fit the shape of the tailpipe. I take it other 5th gen's have rounded tailpipes? Not sure why mine would be any different. I'll take pics when I get home for work.
 
Thesoundofpanic9 said:
My tailpipe is shaped like an egg and the exhaust tip is round. I would need to bend the exhaust tip to fit the shape of the tailpipe. I take it other 5th gen's have rounded tailpipes? Not sure why mine would be any different. I'll take pics when I get home for work.
Click to expand...

The rest look just like the OP's pipe. Yours sounds like it has been changed out or squashed offloading.

Dan
 
I'm attempting to take the chrome tip off of mine and it appears a portion of the lip was crimped and I can only get the damn thing to wiggle around with lots of effort and WD40, sans clamp obviously.

Any advice for prying it off without bending the shi* out of my tailpipe?

Or I may just cut it off further up for the sake of not dragging it off road. :whistle:
 
Last edited:
Saker said:
Why would you need to bend it?
Did yours come with the 2 inserts and the clamp?

If so, it will fit.
Click to expand...

Thesoundofpanic9 said:
My tailpipe is shaped like an egg and the exhaust tip is round. I would need to bend the exhaust tip to fit the shape of the tailpipe. I take it other 5th gen's have rounded tailpipes? Not sure why mine would be any different. I'll take pics when I get home for work.
Click to expand...

Danimal said:
The rest look just like the OP's pipe. Yours sounds like it has been changed out or squashed offloading.

Dan
Click to expand...

Agree with Danimal....

You could always do this and kill 2 birds with one stone!

http://www.toyota-4runner.org/2013712-post75.html
 
I'm looking for one of these exhaust tips if anyone is "uninstalling"

Never mind ... found one!
 
Last edited:
You must log in or register to reply here.

Similar threads

S
2.7L with W59 Xmission - Clutch job stuck - Sanity check
Replies
2
Views
1K
davidch
D
P
TRD roof rack end clamp fell off
Replies
0
Views
1K
Pavement Tested
P
W
How to turn your Toyota 4Runner into a camper over a single weekend!
Replies
1
Views
3K
Thoseguys26
Thoseguys26
Clifford
Bump stops spin- cannot remove
Replies
2
Views
369
Clifford
Clifford
J
ARGH! 30k Mile Oil Leak-Front Timing Cover!
Replies
10
Views
8K
johnnygraphic
J

Members online

Total: 421 (members: 4, guests: 417)

Forum statistics

Threads
278,309
Messages
3,554,068
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top