FS: 8-Wrap Landcruiser Coils - $60 + S/H (Atlanta, GA)

[Koko4]

I’ve decided to sell my 8-wrap LC coils. I put them on my 4Runner and they lifted the rear a bit higher than I was anticipating. You can see the color codes on the pictures (one side is hard to distinguish). I believe them to be 8-wraps, but was never 100% sure on this. Located in Snellville, Georgia (outside of Atlanta).

I'd like $60 + you pay s/h. I can ship whichever method you prefer.

*Note: they are a bit dirtier than in the picture because I went offroading. Picture is to clearly show color code.*

 

[MattJakobs]

Shipping to 23452? Calling dibs but going to check the color codes to make sure they're 8 wraps. Do you have any pictures of them installed? Do you know how many miles are on them?

 

[yosh2000]

Calling dibs but going to check the color codes to make sure they're 8 wraps.

you cant call dibs, but then say you are going to confirm color codes. either you're in or out...

 

[MattJakobs]

you cant call dibs, but then say you are going to confirm color codes. either you're in or out...

Just checked color codes and confirmed. Just wanted to make sure so I guess that makes me in.

 

[Scramble]

But you cant see the color codes on the right? A little wipe down with a rag before taking pics would have been nice.

 

[Koko4]

But you cant see the color codes on the right? A little wipe down with a rag before taking pics would have been nice.

I wiped off what I could - the color codes on the right were not totally visible. Just that one color was left.


And Matt, I can check on shipping prices in the morning at the UPS store. I will find a box tonight and take it to them in the morning to get an estimate on shipping costs.

 

[Koko4]

Just wiped them off with brake cleaner and took better pictures. As you can see in the picture, they are obviously used. I had to use a rented spring compressor to compress the driver's side and fit it between the axle / body, while leaving the panhard bar attached. You may have to do the same unless you have a panhard drop bracket installed.

I also measured them. One is approximately 19" (the one that does not have the complete color codes visible) and the other is approximately 19.25" - 19.5". I hope that helps with the identification.

I found a box that they will fit in, and will check the shipping prices first thing in the morning. If you have a cell #, you can PM me it or text me at 404-626-3158, and if you'd like I can send them as soon as tomorrow (after doing PayPal, of course).

Thanks guys.

 

[khongcha]

Shipping to 65803

 

[Koko4]

I'll get everyone's quotes first thing in the morning.

So far the order is this:

1. MattJakobs (23452)
2. Scramble (10950)
3. Khongcha (65803)

 

[absalom]

PM sent - I already know how much shipping is going to be and I'm ok with the price. Just send me your paypal info whenever.

 

[Koko4]

Shipping prices-

23452 - $22
10950 - $26
65803 - $23

MattJakobs was first in line, but I think he decided against them, so scramble is second, followed by khongcha, then link12. Let me know. UPS store is open until 2 but they won't ship until Monday.

 

[Scramble]

Shipping prices-

23452 - $22
10950 - $26
65803 - $23

MattJakobs was first in line, but I think he decided against them, so scramble is second, followed by khongcha, then link12. Let me know. UPS store is open until 2 but they won't ship until Monday.

I'll take them. PM me your PP info. Thanks!

 

[Koko4]

I'll take them. PM me your PP info. Thanks!

10-4, sold and pending PayPal!

 

[Scramble]

10-4, sold and pending PayPal!

Money Sent!

 

[Koko4]

Sold!

 

[ShaneRC51]

PM sent - I already know how much shipping is going to be and I'm ok with the price. Just send me your paypal info whenever.

I think this dude just got the shaft...

 

[Koko4]

I think this dude just got the shaft...

Scramble was #2 in line - the guy didn't get "the shaft" - I was just following the order of the posts. I wish I had 1000x of these springs to sell, though, because I remember it took me forever to find them and it seems like someone is always looking!

 

[absalom]

I think this dude just got the shaft...

I was biting my tongue lol

 

[yosh2000]

I think this dude just got the shaft...

I was biting my tongue lol

you didnt call "dibs"...no shaft here...!!

ultimately [MENTION=109102]MattJakobs[/MENTION] got the shaft...he called "dibs" and never got them...oh thats right, he called "dibs" and backed out.

what is this world coming to when you cant even trust a man's "dibs"...

 

[Brique]

The dibs in America used to be much higher grade, but now with all the Chinese steel being imported, overall dib quality seems to have degraded significantly.