Rigid Industries (Lights & 5thGen Grille Introduction) *Group Buy* Spring 2015

[jicko]

Does anyone have any suggestions as to the best way of wiring up the roof rack LED bar? Where and how did you run your wires to the hood? I have to wire mine up soon and hopefully they will look as nice as [MENTION=57196]needsmoresalt[/MENTION] !

I recommend that you ground the bar to the rack and sneak 1 wire, preferably a "black" wire, but have it carry your +12V down from the side of your windshield into the engine compartment, where you will have your relay installed. This should be the cleanest install, for 1 single 40" bar.

 

[TotalAutomotiveLV]

Does anyone have any suggestions as to the best way of wiring up the roof rack LED bar? Where and how did you run your wires to the hood? I have to wire mine up soon and hopefully they will look as nice as [MENTION=57196]needsmoresalt[/MENTION] !

Good info here - fjcruiserforums.com/forums/how-technical-articles/61976-roof-rack-lights-wiring-gauge-installation-parts-1-2-3-a.html

 

[Z0MBIEproof]

Any chance I can still get in on one of those 5th Gen 2015 led grilles?

 

[TotalAutomotiveLV]

Any chance I can still get in on one of those 5th Gen 2015 led grilles?

Those are now shipping! Please contact us via PM if youd like to order one.

 

[Headhunter14]

Those are now shipping! Please contact us via PM if youd like to order one.

Is it too late to get in on the fog light order?

 

[4Funnr]

Is there a plug and play fog light kit for 2010-2013 T4R?

 

[TotalAutomotiveLV]

Is there a plug and play fog light kit for 2010-2013 T4R?

Rigid has their lower grill with openings for D2/Dually lights, which would be the closest thing to a a fog light plug and play kit. You can see the product below,Click here to order. You would also need the lights as well if you didn't already have a set.

PM for pricing or to order

 

[hoe_nah]

any news on the fog kits? is it possible to add some stuff to my order?

 

[TotalAutomotiveLV]

For those who have open orders still, if you would like to add or change it please PM us or reply to your order email and we will extend the same discount..

 

[TotalAutomotiveLV]

FINALLY! We have got the very first order of fog light brackets and will begin shipping all of the pre-orders from our last group buy today:guitar3:

We have limited sets in stock so if you want a set, we highly recommend placing your order before these are all gone

PM us for the T4R Rigid discount code

 

[manofsteele2003]

Sweet, I've been anxiously waiting for these bad boys.

 

[TotalAutomotiveLV]

We were the first to ship these out with over 30+ sets shipped out last week. Who will be the first to install them and post up?

 

[hoe_nah]

FINALLY! We have got the very first order of fog light brackets and will begin shipping all of the pre-orders from our last group buy today:guitar3:

We have limited sets in stock so if you want a set, we highly recommend placing your order before these are all gone

PM us for the T4R Rigid discount code

just wondering when mine will be shipped out?

 

[hoe_nah]

any updates? did anyone get the fog kit yet?

 

[hoe_nah]

GOT UM...thanks to the guys at tap auto, and a shout out to mike for helping me over the phone.

side note: installed these and had to reaim them a few times, found that if you look closely at the directions the tab on the opposite side of where the bracket screws in, stays on the outside of the fog light hole.

 

[balistikboy]

any updates? did anyone get the fog kit yet?

I haven't received any update email lately either. Not sure where on the preorder list I was for these. I'm assuming I wasn't in the top 30 or so since I haven't received a shipping notice.

Anyone have any pics of them installed? Post them up!

 

[CheletteTRDPRO]

I have had mine for three weeks and are installed there cool but not the greatest design

 

[manofsteele2003]

I have had mine for three weeks and are installed there cool but not the greatest design

Agreed, just installed mine and they're not the best fit and finish.

 

[hoe_nah]

yeah i thought they were going to sit flush inside the stock area. i had to fiddle around with them to get proper aiming and alignment

 

[manofsteele2003]

yeah i thought they were going to sit flush inside the stock area. i had to fiddle around with them to get proper aiming and alignment

Yes that was also a pain, with what little adjustments there are I had to do it with the bumper off then put it loosely in place to check before reassembly.