final product. coffee table has a cut out for a tumbler and workspace. The right drawer has a simple cover to serve as a table / makeshift changing st

final product. coffee table has a cut out for a tumbler and workspace. The right drawer has a simple cover to serve as a table / makeshift changing st

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Test fit of equipment. This load out will change once I mount a roof rack and throw a box on top to house recovery gear. Plenty of room for mechanic

Test fit of equipment. This load out will change once I mount a roof rack and throw a box on top to house recovery gear. Plenty of room for mechanic

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Decided to added a 'coffee table' spring pop up to one drawer. Because of the compression locks, I had to space the pop up to give it clearance, and

Decided to added a 'coffee table' spring pop up to one drawer. Because of the compression locks, I had to space the pop up to give it clearance, and

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
2 coats of black stain and 2 coats of poly, love the dark look. I used carriage bolts on the outside (1 inch) with jam nuts in the drawer recess. I

2 coats of black stain and 2 coats of poly, love the dark look. I used carriage bolts on the outside (1 inch) with jam nuts in the drawer recess. I

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
I opted to use framing L brackets to mount the drawer system. I like this as it s strong than turnbuckles but I can still remove the drawer if needed

I opted to use framing L brackets to mount the drawer system. I like this as it s strong than turnbuckles but I can still remove the drawer if needed

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Taped off the drawer front to prevent splintering when cutting. 3/4 blatic on front of 1/2 drawers for strength and depth.

Taped off the drawer front to prevent splintering when cutting. 3/4 blatic on front of 1/2 drawers for strength and depth.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Final drawer front aligned and braced for cut. Once cut, i glued and secured after final test fit in drawer

Final drawer front aligned and braced for cut. Once cut, i glued and secured after final test fit in drawer

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
Built a mock drawer front to practice before the final product, huge help as it allowed me to shift and adjust spacing

Built a mock drawer front to practice before the final product, huge help as it allowed me to shift and adjust spacing

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
measuring depth of the compression latch

measuring depth of the compression latch

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
measurement for bracket to allow compression latch to secure to top of drawer.

measurement for bracket to allow compression latch to secure to top of drawer.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
simple drawers with 1/2 inch baltic all around. No fancy joints here.

simple drawers with 1/2 inch baltic all around. No fancy joints here.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
measuring and bracing the divider. If I did this again, I would cut pieces of wood to use to brace where drawers go and ensure even fit.

measuring and bracing the divider. If I did this again, I would cut pieces of wood to use to brace where drawers go and ensure even fit.

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
My first shot at pocket holes. This was to hold the sides, back and center in place. Eventually used screws and glue to firmly secure and ensure I h

My first shot at pocket holes. This was to hold the sides, back and center in place. Eventually used screws and glue to firmly secure and ensure I h

  • Media owner K5to4R
  • Date added Feb 26, 2021
  • Reaction score 0
  • Comments 0
K

K5to4R Drawer Build

  • Items 13
  • Album owner K5to4R
  • Date created
This was the first modification to my 2021 TRD ORP. It was also my first attempt at any sort of woodworking. It was a great product, I learned A LOT, made mistakes along the way but learned how to recover from them. Great project and now I have some great storage at a fraction the price of pre bu
Click to expand...
There are no comments to display.

Album information

Album owner
K5to4R
Date created
Item count
13
View count
0
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

K

K5to4R

Media items
13
Albums
1
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Members online

Total: 3,612 (members: 3, guests: 3,609)

Forum statistics

Threads
278,316
Messages
3,554,121
Members
248,016
Latest member
Advally Service

Share this page

Back
Top