Recent content by Bonesetter

Hey everyone, I'm wondering if anyone has added the GZ Yeti Link kit to their rig, and if so how did you end up running the cables? They're large (6awg) with large attachments on the ends, so going through the engine firewall seems to be a no-go. I could run along the frame underneath, but then...

4th gen front bumper cover, crash bar, rails and crossbars. Austin TX. Front bumper cover has a cutout in the lower grille for a short stealth light bar and relocated license plate mounts. Intact driving light and turn signal housings. Rails and crossbars have some minor scratches but are...

FS: Husky floor mat set for 5th gen, $150, Austin TX My buddy traded in his 5th gen for a 4th gen because he was jealous of mine, and he's got the floor mats up for grabs for $150. Less than a year's wear on them, retail is about $310 new. He's not willing to ship, but can meet up with anyone...

My buddy traded in his 5th gen for a 4th gen because he was jealous of mine, and he's got the floor mats up for grabs for $150. Less than a year's wear on them, retail is about $310 new. He's not willing to ship, but can meet up with anyone in the Austin area or surrounding. PM for his contact...

Wavian gas can and gas can holder, 1.5" square tubing from HD, step drill bit, a smidge of hacksawing, and some 3/8" bolts with locking washers and nylon nuts.Not including gas can, about ~$100 including gas can holder. WO wanted ~$300 for their setup. I'll pull it and paint it next week.

Update: the wiring on the new signals was, indeed, reversed. Rewired with white to white/black, black to green, and everything is working now. Many thanks to y'all for the assistance!

As far as I can tell, the bulb housing is sealed and hard-wired in, so no pulling it out to reseat. I’ll try switching wires tomorrow to see if that fixes. Edit: Thanks so much, everyone, for weighing in, and sorry I didn't resize the pic. I'll keep you posted.

Used quick splices to wire the resistor in between the ground and power wires. The bulbs wouldn't light up before the resistors were placed either, though. I put the resistors in after noting hyper flash on my dash and rear signals.

Searches on both forum and Google haven't turned anything up, so I am once again asking for the assistance of those of you, probably all of you, who know more about this than I do (not a high standard to meet, and it's consistently exceeded by an enormous margin here on the forum). Put my new...

FS or trade: 2005 factory roof rack, running board(s). Austin TX. Best offer. Factory roof rack, including cross bars and all hardware (1 small crack in outer housing of rack mount), plus 1 driver side running board in good condition, 1 passenger side running board in moderately jacked up...

Ordered a set of sliders at 1201 the morning of code activation. Was advised today that sliders are on at least a 4 week production time. Not complaining, just sharing info. Thanks for setting this up, OP!

I’m a 4th gen guy, but my buddy’s currently backcountry hunting in NM in his 5th gen and sent me this to rub in the fact that I’m stuck working while he’s breathing freash air, so I thought I’d share it with you guys.

Rear wheel click/clank/rattle solved Problem solved: I'll drop this in here to add to the near-endless list of click/rattle/clunk threads. Turns out the click and rattle I was hearing came from two separate sources: 1. The mech who replaced the rear axle left a bolt loose on the sway bar...

Dude, thank you so much. The Icon was put in before I got the rig, so I had no idea. I really appreciate it.

For the record, there’s not even half a leaf on the shade tree that I wrench under, which leads me to this question. Got t-boned on my rear wheel several weeks ago, leading to insurance paying for the replacement of a bent rear axle, among other things. Got the rig back 4 days ago, driving with...