SOcalTRAIL
New member
Damn bro, truck is looking insane. Loooove those wheels.
Adio3x's Build/Pic thread.
- Thread starter adio3x
- Start date
Qjake
New member
Andrew,
Would you mind taking a couple pics with the centercaps on? I'm really liking those wheels, I think they'd look awesome on my mag grey:boink:
Also these are the Koing Countersteer Offroad's shown on the FN Wheels site correct? Where do I keep getting 6 shooters from :shrug:
Would you mind taking a couple pics with the centercaps on? I'm really liking those wheels, I think they'd look awesome on my mag grey:boink:
Also these are the Koing Countersteer Offroad's shown on the FN Wheels site correct? Where do I keep getting 6 shooters from :shrug:
adio3x
New member
Thanks all!!!
As for the centercaps, its a real pain to put them in now lol. The only way to do it is, jack the car up and take off all the wheels. I'll post some pics of my buddy Joe's FJ, he has them too but with the centercaps.
The wheels are Konig Six Shooters. I don't think they have them up on the site yet. The countersteer offroads are a little different if you look at the spokes and I think they only come in 16s.
adio3x
New member
Just a quick update!
Went to the FJ Jamboree a few weekends ago. I had a blast wheeling with all those FJ guys, the park was pretty cool too. It was very tight in most spots, ended up getting a whole lot of rock rash on the new wheels and unseating a tire, luckily it reseated as I put more air in.
Limb risers did a great job!
So I got home and was unhappy with the situation that happened to my tires. Got a great deal on some 295/70/17 Nitto Trail Grapplers. Fit so much better, only bad thing is they rub pretty hardcore in the front. I may end up trimming a little of the rear fender and doing the BMC upfront.
And finally this! I got bored with the lightforces, great output, but not as great as these.............
Ok I'm done for now. See you next summer when the TRD supercharger is suppose to come out :hello:
Went to the FJ Jamboree a few weekends ago. I had a blast wheeling with all those FJ guys, the park was pretty cool too. It was very tight in most spots, ended up getting a whole lot of rock rash on the new wheels and unseating a tire, luckily it reseated as I put more air in.
Limb risers did a great job!
So I got home and was unhappy with the situation that happened to my tires. Got a great deal on some 295/70/17 Nitto Trail Grapplers. Fit so much better, only bad thing is they rub pretty hardcore in the front. I may end up trimming a little of the rear fender and doing the BMC upfront.
And finally this! I got bored with the lightforces, great output, but not as great as these.............
Ok I'm done for now. See you next summer when the TRD supercharger is suppose to come out :hello:
adio3x
New member
Sorry Mike, didn't see your question at the bottom of the page.
Backspacing is 5"
FactoryRide
New member
that looks killer man. :jaw drop: What happened with the projectors? You still working on them?
mikey's2010SR5
New member
All good. How about some more photos with the 295s? That is the route I am thinking of come next set of tires.
MeBe4running
New member
My goooodness me..... that is awesome! :guitar3:
Qjake
New member
The new Six's? Man that blows! Is it on the spokes? I've been considering a set of them but was concerned with the spokes being out so for that they'd get beat up. Liking the new meats, looking good!
adio3x
New member
Haha thanks Spencer. I'm going to postpone the build on those. Almost done with one of them, I just don't have time or a place to work on them while at school.
Heres a side pic, you can see how close they are to the fenders. I forsee some damage if they get stuffed. Its either trim the fender or I don't think anyones done a body lift before, I don't really want to, but thats an option.
It was all mostly on the lips. We were crawling narrow creek beds with some boulders on both sides. Most of all the rigs went around the rocks, while I had to crawl over them lol. Atleast I got to use my sliders. I don't think you should worry about scraping the spokes, unless you're making contact with the body, I think you should be fine.
Last edited:
FactoryRide
New member
I gotcha man. Looks good either way.
MeBe4running
New member
Did the body mount chop yesterday, my buddy took a piece of a hummer h1 bumper again and welded it in lol. Absolutely no rubbing at all at full lock!!! Anyone that plans on running my setup ~ Spacers and a 295, I suggest you grind down this piece or just cut it off.
This hummer where you're outsourcing your parts from must have little left on it nowadays
Looks great Andrew!
and more switches
Frikking nice job Andrew! Truck looks amazing. And another video with killer soundtrack. I'm sure you can find some Krewella or Skrillix to play with
Okki
mrvandelay
New member
What exactly is that thing you suggest we cut in addition to the BM?
adio3x
New member
Not sure if the TE's have it, but I'm pretty sure its just a bracket to hold the rocker panel in place.
NorthWest 4R
New member
Isn't that the front lower fender mount?
Similar threads
