Eibach Pro-truck lift

[honda250xtitan]

Does anyone make a poly replacement top hat to use instead of the stock rubber? ]

ehhh that'll squeak and you'll never be able to clean it/grease it. stock rubber works fine for this application since it doesn't really move like you'd see in a control arm movement.

 

[honda250xtitan]

Ready when you are... already ordered your 1" lift rear coils in hoping that works with whatever you come up with for the front.

those coopers look PISSED:faint: i dig it

 

[Ryan at Eibach]

I think we'll be about 20% off web price with free shipping. If any of you want to pull the trigger now just PM me and I'll price it out.

bump

 

[BanditTRD]

I just purchased this kit for my '16 Trail. Would I have any options to lift the rear an additional .5 inch to get a little bit of rake? a 1.5 inch rear spring opposed to the 1 inch spring that comes with it? Or 1/2 inch Cornfed rear spacer perhaps?

 

[Lifeline]

I just purchased this kit for my '16 Trail. Would I have any options to lift the rear an additional .5 inch to get a little bit of rake? a 1.5 inch rear spring opposed to the 1 inch spring that comes with it? Or 1/2 inch Cornfed rear spacer perhaps?

I actually have the 1/2 inch cornfed rear spacer. I’m contemplating installing it with my Eibach lift when it comes in as well. Just sent Ryan a message for his feedback actually.

 

[MarkAlan]

Putting my lift on tomorrow.

 

[Ryan at Eibach]

Tell your GX buddies it's time! Our 3/2 kit drops next week.

 

[Ryan at Eibach]

Pulled the trigger on a spare TE37 and tire carrier

 

[JMZ400]

I just purchased this kit for my '16 Trail. Would I have any options to lift the rear an additional .5 inch to get a little bit of rake? a 1.5 inch rear spring opposed to the 1 inch spring that comes with it? Or 1/2 inch Cornfed rear spacer perhaps?

Wheelers offers a T12 coil made by Eibach that is supposed to give about 1.5 on the fifth gen. I picked a set up to use with this kit for the same desire just haven't installed anything yet. I'm feeling ike I'm wanting to get closer to a 3" lift so I'm deciding where to go from here. Has me stalled out.

Sent from my SM-A205U using Tapatalk

 

[BanditTRD]

Wheelers offers a T12 coil made by Eibach that is supposed to give about 1.5 on the fifth gen. I picked a set up to use with this kit for the same desire just haven't installed anything yet. I'm feeling ike I'm wanting to get closer to a 3" lift so I'm deciding where to go from here. Has me stalled out.

Sent from my SM-A205U using Tapatalk

My main concern is, the rear shocks say they are rated for 0-1" lift, so would I run into any complications if I were to install those springs?

 

[Ryan at Eibach]

My main concern is, the rear shocks say they are rated for 0-1" lift, so would I run into any complications if I were to install those springs?

You'll be fine.

 

[SunValleyV8]

bump

PM sent on pricing and question of lift with Eibach coils and 0-2.5 adjustable front shock.

 

[MarkAlan]

Lift is on, and it looks great. It drives great, a little more firm than stock but in a good way. Very little nose dive, and almost no roll when cornering. This is how it should come from the factory. I did add adjustable control arms, to get it to go back to factory settings since the wife will be driving the 4Runner. Yes I know they are not necessary. The 4Runner has been leveled with no Bro rake. This is a very nice kit. Thanks Ryan for all the help. I will post pics as soon as it stops raining.

 

[jcalvert86]

I'll get some pics up when we get the rig in for test fit

What's the hold up? :whip2:

Just ordered some Icon UCAs and don't want to take the 20 Pro back to the shop until it's ready to have the Cornfed spacers replaced with the new Eibach kit.

 

[alcomedic]

I think we'll be about 20% off web price with free shipping. If any of you want to pull the trigger now just PM me and I'll price it out.

PM sent. thanks

 

[gjcarving]

Tell your GX buddies it's time! Our 3/2 kit drops next week.

Cool! Any chance an adjustable Gx 460 is on the block? Looking for a slight lift like 1.5/1 or 1/1. Really want it for the valving.

 

[Steel28]

What's the hold up? :whip2:

Just ordered some Icon UCAs and don't want to take the 20 Pro back to the shop until it's ready to have the Cornfed spacers replaced with the new Eibach kit.

Tried to look but can’t find release info. Looking to grab it for my 2020 Pro.

 

[85GT-79FJ40]

Last week I installed the rear springs from this kit along with OME 883's in the front. Seems to be a decent match up for those like myself that only wanted about 2" in the front. I put a budbuilt winch mount and a 9500lb cheap smittybuilt winch on it too so I likely didn't get 2". But along with 5100's the truck drives worlds better than it did with the stock setup.

 

[ForRun]

Looks like I am not the only one anxiously waiting details of the 19-20 TRDPRO front lift springs.......

Ryan.... throw us a bone!

I'll get some pics up when we get the rig in for test fit

Tried to look but can’t find release info. Looking to grab it for my 2020 Pro.

Ryan, what's coming up for the pros? Just picked one up and sign me up!

 

[Ryan at Eibach]

All weekend PM's replied :help: