Victory Blitz/ARB skids/spidertrax installed

[Starsky]

Just to clarify - it's always on when the 4Runner is on. It goes off when I turn the truck off.

 

[papadop88]

Looks great, OP!

 

[Paragon1]

Yeah I just split the wire to my switchpro. I think that took longer than installing the sliders just because of routing the wires and trying to make it look clean.

Gotcha. Incidentally, how did you go about wiring up the rock lights? Victory didn’t have anything on their site, or if they did I missed it.

 

[stay_tuned]

Gotcha. Incidentally, how did you go about wiring up the rock lights? Victory didn’t have anything on their site, or if they did I missed it.

Yeah i was curious on this too, mainly needing to know which way to route wires.
:thanks:

 

[pookguy]

Gotcha. Incidentally, how did you go about wiring up the rock lights? Victory didn’t have anything on their site, or if they did I missed it.

Yeah victory didn’t have any wiring diagrams. What I did was run a wire from the domerock in the A pillar down through the firewall.
For the lights I connected them all up and ran that wire up through the engine bay on passenger side. Took that wire and connected to the domerock wire. Then from there took all the wires and connected to the switchpro. This allows me to turn the lights on demand with the switch and then also when I unlock from the fob or open the door.

 

[Paragon1]

Yeah victory didn’t have any wiring diagrams. What I did was run a wire from the domerock in the A pillar down through the firewall.
For the lights I connected them all up and ran that wire up through the engine bay on passenger side. Took that wire and connected to the domerock wire. Then from there took all the wires and connected to the switchpro. This allows me to turn the lights on demand with the switch and then also when I unlock from the fob or open the door.

Appreciate it, just to make sure nothing gets lost in translation is there any way you can post a quick diagram? Switchpro has about a 2 week lead time so i just want to get everything pre-positioned for when it arrives.

 

[Tennfly]

Victory Sliders

I ordered the Victory 4X4 Strike sliders.
I needed a step for my wife.
They are bolt on to the frame. My driver's side holes did not line up with the frame holes. Tried everything and failed.

 

[Victory 4x4]

Appreciate it, just to make sure nothing gets lost in translation is there any way you can post a quick diagram? Switchpro has about a 2 week lead time so i just want to get everything pre-positioned for when it arrives.

This guide is very helpful!

Rock Lights as Courtesy Lights on 4Runner - LED Illumination Package

 

[pookguy]

Yeah I used this diagram, but didn't bother with a relay

This has some good info on the module where I found it:
DomeRock Module for Courtesy Rock Lights V4 by DSIM Solutions | Tacoma World

 

[Sbenis]

Good looking rig !

 

[Paragon1]

I ordered the Victory 4X4 Strike sliders.
I needed a step for my wife.
They are bolt on to the frame. My driver's side holes did not line up with the frame holes. Tried everything and failed.

Did you try the passenger side? how far off were they?

 

[Victory 4x4]

I ordered the Victory 4X4 Strike sliders.
I needed a step for my wife.
They are bolt on to the frame. My driver's side holes did not line up with the frame holes. Tried everything and failed.

I'm sorry to hear this! Did you reach out to tech support? Send us an email at [email protected] and we can take care of this!

 

[Tennfly]

I got the passenger side on, as the frame holes were mostly aligned with the slider's holes.
The driver's side is another story. The holes were off 1/2 to 1 inch off. Tech support was called, but not much going over there with the Wu Flu shutdown.
I think I'll have to wallow out the holes on the slider and then put a large washer for support between the slider and the bolt.