3rd Gen T4R DIY Maintenance, Repair and Modification Videos

mtbtim said:
While I think this video is cool and well done, how cost effective is this rebuild compared to just buying a rebuilt alternator? Usually you only replace the parts that are necessary and most of the time an alternator that starts having charging issues is because the brushes have worn down. You didn't say so at the beginning of the video but were the bearings actually bad or are you replacing them just because?
Click to expand...

When I took the OEM alternator off and replaced it with a HO alternator, it was in perfectly fine condition. I did this literally in order to make a video of the process and secondarily to have a "rebuilt" trail spare that I know I could rely on. Something I did off camera is clean up the case and insides as well.

mtbtim said:
Anyway, thanks for sharing this. By the way, how much money did you spend on all the parts to rebuild your alternator? in case you missed our video on this subject, here's ours. I added your video to the Table of Contents. You did a good job filming this. You should make more videos.
Click to expand...

I've been a big fan of PartsOuq as of late. From them, all in all, it was about $70 shipped for all the parts to do this.

I appreciate the complements on the video (Weekend Wrench Turner is my Youtube altered ego) and I've been trying to put out one a week for the last 4-5 months or so. Not all of them are working on the 4Runner, but are generally centered around working in the garage while my toddler is napping on the weekends. Been working on restoring an old floor model drill press lately, though a rear axle seal job has put off completion of that lately.

Sincerely though, you and Sean were the inspiration to start doing these videos. In fact, some of the videos I've done are just my take of things I've watched and learned from you both as far as working on the 4Runner. I in no way claim to do a better job than you both do, but do hope to at least contribute some shared knowledge to those who watch.
 
weekendclimber said:
When I took the OEM alternator off and replaced it with a HO alternator, it was in perfectly fine condition. I did this literally in order to make a video of the process and secondarily to have a "rebuilt" trail spare that I know I could rely on. Something I did off camera is clean up the case and insides as well.



I've been a big fan of PartsOuq as of late. From them, all in all, it was about $70 shipped for all the parts to do this.

I appreciate the complements on the video (Weekend Wrench Turner is my Youtube altered ego) and I've been trying to put out one a week for the last 4-5 months or so. Not all of them are working on the 4Runner, but are generally centered around working in the garage while my toddler is napping on the weekends. Been working on restoring an old floor model drill press lately, though a rear axle seal job has put off completion of that lately.

Sincerely though, you and Sean were the inspiration to start doing these videos. In fact, some of the videos I've done are just my take of things I've watched and learned from you both as far as working on the 4Runner. I in no way claim to do a better job than you both do, but do hope to at least contribute some shared knowledge to those who watch.
Click to expand...

Gotcha Scott. Well, it's cool you made the video because no doubt people will benefit from it. $70 is up there and I wonder what a Denso Rebuilt would cost. But, who knows really what you're getting when you buy a rebuilt one. Are they replacing the bearings or are they just replacing the parts necessary to get it running again.

Good to hear our videos inspired you to contribute to the DIY community.
 
Auto Trans Shifter Bushing Replacement & Transfer Case Shifter Seat Replacement

If you wanted to fix your sloppy Auto Trans Shifter, and at the same time replace your Transfer Case Shifter Seat, this video will show you how to get it done.

<iframe width="560" height="315" src="https://www.youtube.com/embed/gCHSRcq-LP8" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
 
Watched about half so far, and I learned about that cool tab on the auto shifter! This is my first automatic, and I had no idea...

Thanks Tim and Sean, and Alison too!
 
Key lock cylinder replacement. check it out boys!



.
<iframe width="560" height="315" src="https://www.youtube.com/embed/daKA8fJVomY" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>



.
 
Wiring problems

Hi, my name is Bruno and i'm new here, i just got a 3rd gen 4runner with 300.000 miles and it's not running for 2 reasons.
It's over heating and someone took the thermostat out and the biggest reason is because it almost caught on fire. it has some wiring problems. i would like to know if someone could help me get a wire diagram for this car and i'll take some photos to get you posted and to let you know if its going well or not.

Thanks for your help.

Bruno Arroteia
 
BrunoArroteia said:
Hi, my name is Bruno and i'm new here, i just got a 3rd gen 4runner with 300.000 miles and it's not running for 2 reasons.
It's over heating and someone took the thermostat out and the biggest reason is because it almost caught on fire. it has some wiring problems. i would like to know if someone could help me get a wire diagram for this car and i'll take some photos to get you posted and to let you know if its going well or not.

Thanks for your help.

Bruno Arroteia
Click to expand...

You might be able to find an online version of the wiring diagram but a better bet might be to just try to find one for sale on Ebay for your year. Lots of people sell the factory service manuals and wiring diagrams.
 
Hilux 167 Snorkel Install

In this video we show you how to install a Hilux 167 Snorkel on your 3rd Gen. This mod is nice for anyone who wheels their rig because water crossings are common for a lot of 4wheel drive trails and this could mean the difference of getting across safely or getting stuck and flooding your rig.

<iframe width="560" height="315" src="https://www.youtube.com/embed/UlSQI_Y8gk4" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
 
mtbtim said:
In this video we show you how to install a Hilux 167 Snorkel on your 3rd Gen. This mod is nice for anyone who wheels their rig because water crossings are common for a lot of 4wheel drive trails and this could mean the difference of getting across safely or getting stuck and flooding your rig.

<iframe width="560" height="315" src="https://www.youtube.com/embed/UlSQI_Y8gk4" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
Click to expand...









Watched the video....Ive never had my A pillar off. If off is the back of the rivets visible and can a person put silicone goop there too to help make sure it all seals
 
3bears said:
Watched the video....Ive never had my A pillar off. If off is the back of the rivets visible and can a person put silicone goop there too to help make sure it all seals
Click to expand...

You are drilling into a void and can't access the back side. I confirmed this morning what Anwar told me and you cannot assess the area where the rivets are being affixed to by pulling off the A-pillar trim piece.
 
mtbtim said:
In this video we show you how to install a Hilux 167 Snorkel on your 3rd Gen. This mod is nice for anyone who wheels their rig because water crossings are common for a lot of 4wheel drive trails and this could mean the difference of getting across safely or getting stuck and flooding your rig.
Click to expand...

Great videos man! Binge watched the videos in your channel LOL. Was planning to do this mod but worried about rust and stuff :D .. Looks really nice tho
 
tylenol650 said:
Great videos man! Binge watched the videos in your channel LOL. Was planning to do this mod but worried about rust and stuff :D .. Looks really nice tho
Click to expand...

How are you going to look cool cruising the mall without this mod. Don't worry about the rust. Just use some touch up paint or clear coat like we use in the video and you're golden.

Glad you like the videos and good luck with your rig.
 
Really would have been nice if he was using a rig with bad ball joints so you could see movement that would require replacement.
 
While Timmy's videos can be a bit longwinded they are very informative, better that most that are out there. Good job.
 
roger65 said:
Really would have been nice if he was using a rig with bad ball joints so you could see movement that would require replacement.
Click to expand...

Yeah, in a perfect world we would have been able to show the movement in some bad ball joints but as the Rolling Stones sang, you can't always get what you want.
 
mtbtim said:
Well thanks Roger. We're glad you approve.
Click to expand...

Watched the upper and lower ball joints ones again yesterday as I was doing my daughters rig. I ran out of time and only did the passenger side upper along with both lowers. Are the uppers ones that wear out as easily as the lowers? Sure was a hassle with marginal tools from O'Riellys.
 
roger65 said:
Watched the upper and lower ball joints ones again yesterday as I was doing my daughters rig. I ran out of time and only did the passenger side upper along with both lowers. Are the uppers ones that wear out as easily as the lowers? Sure was a hassle with marginal tools from O'Riellys.
Click to expand...

The uppers last longer and are not prone to failure like the LBJs are.
 
You must log in or register to reply here.

Similar threads

5VZ-FE
New steering rack, tons of movement
2
Replies
29
Views
80K
phattyduck
P
E
Impossible Rear Drive Shaft Rebuild? Double Cardan U Joint / CV Ball Seat
Replies
2
Views
2K
T4R2014
T4R2014
farmerjon
'98 Limited: swap push button 4WD transfer case for 98 SR5 j-shifter tcase &amp; ADD
Replies
2
Views
2K
TheDurk
TheDurk
N
FS 2000 Limited 4wd w/E-locker $5k Chambersburg, PA
Replies
4
Views
595
Novashards
N
E
Cracked oil filter bracket assembly
Replies
5
Views
2K
eanema
E

Members online

Total: 402 (members: 4, guests: 398)

Forum statistics

Threads
278,310
Messages
3,554,080
Members
248,016
Latest member
Advally Service

Share this page

Trending content

Back
Top