dustin Keeler
Member
Id love to go with you guys and watch LOL
From the looks of your wheeling, I could'nt keep up. Ill look into the bumpers.
ADH8796 4runner Build
- Thread starter ADH8796
- Start date
Id love to go with you guys and watch LOL
From the looks of your wheeling, I could'nt keep up. Ill look into the bumpers.
JWaldz
Moderator
Gotta start somewhere! There are usually bypasses so no worries :thumb3:
ADH8796
New member
Thanks it's taking a little bit for it to grow on me but overall I like it and think it will be a better setup.
Like Waldo said their are normally places for you to drive around. And of course we always have extra seats.
ADH8796
New member
Well since I've switched to the AL rings I've been experiencing balancing issues. With the steel rings I never had any issues everything was always smooth as silk. But immediately after mounting up the AL rings things changed. Not really sure what the issue is so I'm going to dismount the rings and remount them. At this point I'm just hoping I didn't get the rings tightened down evenly and it's throwing off the balance.
ADH8796
New member
Started with the drivers side front tire. Unbolted the ring and made sure the wheel was as centered as possible and then added about 1oz of bb's. I figured it wouldn't hurt anything to add 1oz of bb's per tire so I just went ahead and tossed them in. After I got everything centered and bolted back up I went for a drive and wouldn't you know it no more wobble. I'm going to go ahead and add 1oz of bb's to the rest of the tires just so everything matches but other than that no more wobble.
AddictedOffroad
New member
Good to see you using those bumpers for what they are meant for!
Looks good bro!
Looks good bro!
HedgehogOutdoors
New member
Looks like a fun time, love your rig!
ADH8796
New member
ADH8796
New member
Well I've been trying to figure out blinkers for a while so this is what I ended up doing. I cut up my original blinkers so I could use the bulb socket in the corner bulbs. I wanted to keep my parking lights but I also wanted to utilize the corners as blinks. So I drilled a hole in each one of the corner light housings and with glue and silicone I used the back side of my original blinkers and attached them to my corners.
Along with that I added 2 LED lights to my grill for a little added light output. I really like the way everything came out. I have plenty of light output and everything seems pretty clean.
First pic is just parking lights on and the second pic is with the flashers on.
Along with that I added 2 LED lights to my grill for a little added light output. I really like the way everything came out. I have plenty of light output and everything seems pretty clean.
First pic is just parking lights on and the second pic is with the flashers on.
URBAN ASSAULT
New member
Lights look great.
Great trail pics! I love how you trained your dog to be your spotter
Great trail pics! I love how you trained your dog to be your spotter
ADH8796
New member
Thanks man. Yeah the dogs are great spotters as long as they steer clear of the tires lol.
ADH8796
New member
Thanks! I'm running 1" BL
Dous
New member
Nice small amount. After my set of tires wear out I am possibly going up to 35's but it would be without BL, it would be a lot of trimming!
ADH8796
New member
That's what I did with my last build. It's really not that much more trimming than to run just 1" BL in my opinion. But they both have their advantages.
Here's my last build for reference
99 Highlander on 35's E-locker. Build thread: ADH8796's 1999 4Runner Build-Up Thread - YotaTech Forums
Last edited:
ADH8796
New member
Thanks! Actually a group buy that [MENTION=58830]ARKRWLR[/MENTION] pointed out to me over on TacomaWorld. But same lights that everyone else has been selling in their group buys on this board.
