Black Friday Deals

[AuSeeker]

Thank you!!! Any idea what regular price for the DT long tubes for our v8 trucks go for? Does $708 sound like regular price or a bf deal?

Jason Burtman sells the DT long tubes for the 2003/2004 for $729.98, Doug Thorley lists them on their site for $750.

Burtman Industries[2752]=2041018469&opt[8173]=

The price shown at the above link is for the shorties, you have to use the drop down menu to select the long tubes to see that price.

 

[montijo505]

White knuckles sliders are 15% off

White Knuckle are BEEF.


Sent from my iPhone using Tapatalk

 

[Bluesky 07]

Maybe this thread is for 4R gear only but couldn’t pass up this deal at Home Depot. 36” W x 18” D x 62” H (closed), regularly $598, on sale for $398 (I believe through 12/4 but check to be sure) minus another 10% veterans discount for a total of $358.20 plus tax. Link

 

[roy326]

Ironman4x4

Full skids: $509 shipped
2” or 2.5” lift $599 shipped (springs /shock/strut)

 

[MrBruns]

does anyone know if these lo-pro winch bumpers affect the TSS front he new 4runners ?

I too had this question. Ive been running some tests with a pool noodle strapped to the front of the 4r. Ive had it as low as 2 inches below the Toyota garnish. No effect on the sensor. I gave this information to C4 with a response saying that this sensor wouldn't notice the pool noodle material. Said it had to be metal or aluminum of some sort. So I ran the same test with aluminum foil wrapped around the noodle. Still no effect on the sensor. Ive also been waiting for accurate measurements on where this bull bar sits. From C4 and many pictures ive seen the bull bar starts just below the Toyota letters. The bar is 1 and 3/4 in diameter and comes out about 3 inches from the front of the garnish. These measurements and tests were for the full height bull bar option. The mid height bull bar i think would be out of the question as it looks to run directly in front of that sensor. Hope this helps. Aside from actually buying this bumper and installing it before powder coating it to run a 100% accurate test, im not sure what else to do.

 

[snowpeak]

I too had this question. Ive been running some tests with a pool noodle strapped to the front of the 4r. Ive had it as low as 2 inches below the Toyota garnish. No effect on the sensor. I gave this information to C4 with a response saying that this sensor wouldn't notice the pool noodle material. Said it had to be metal or aluminum of some sort. So I ran the same test with aluminum foil wrapped around the noodle. Still no effect on the sensor. Ive also been waiting for accurate measurements on where this bull bar sits. From C4 and many pictures ive seen the bull bar starts just below the Toyota letters. The bar is 1 and 3/4 in diameter and comes out about 3 inches from the front of the garnish. These measurements and tests were for the full height bull bar option. The mid height bull bar i think would be out of the question as it looks to run directly in front of that sensor. Hope this helps. Aside from actually buying this bumper and installing it before powder coating it to run a 100% accurate test, im not sure what else to do.

That’s interesting. Thanks for sharing your progress! This should be its own thread imo to keep a discussion going so we can get a definitive answer. Black Friday sale or not, I think it’s worth it.

Anyone see any deals on Bilstein 6112?

 

[steven350]

I too had this question. Ive been running some tests with a pool noodle strapped to the front of the 4r. Ive had it as low as 2 inches below the Toyota garnish. No effect on the sensor. I gave this information to C4 with a response saying that this sensor wouldn't notice the pool noodle material. Said it had to be metal or aluminum of some sort. So I ran the same test with aluminum foil wrapped around the noodle. Still no effect on the sensor. Ive also been waiting for accurate measurements on where this bull bar sits. From C4 and many pictures ive seen the bull bar starts just below the Toyota letters. The bar is 1 and 3/4 in diameter and comes out about 3 inches from the front of the garnish. These measurements and tests were for the full height bull bar option. The mid height bull bar i think would be out of the question as it looks to run directly in front of that sensor. Hope this helps. Aside from actually buying this bumper and installing it before powder coating it to run a 100% accurate test, im not sure what else to do.

wish c4 would just extend/raise the pull bar and sell that as the new norm

 

[Kryptoroxx]

That’s interesting. Thanks for sharing your progress! This should be its own thread imo to keep a discussion going so we can get a definitive answer. Black Friday sale or not, I think it’s worth it.

Anyone see any deals on Bilstein 6112?

Honestly no I haven't. Battleborn has a 15% sale but during normal pricing I noticed I got a better deal with the t4r discount than I would have if I went with the black friday deal. The difference us less than 30 bucks though so really we aren't talking about a serious increase/discount.

Sent from my SM-G965U using Tapatalk

 

[JuniorPigeon]

I tried the Rotopax website and no luck the BF2019 coupon for 15% off, "coupon invalid"... eBay has some decent price on Rotopax too

They ended up fixing the code, got a few goods and it worked perfect. I believe it's still active as well.

 

[CV4RNR]

Any deals still happening? Lifts?