CBI Front Bumper Install

[noobshooter]

A couple of month ago I called CBI to order a front bumper. Nathan said that CBI was in the process of making some changes to the design of the bumper. He asked if I wanted to order the old design, or wait a couple of months and wait for the new design. I decided to wait and this is the bumper I received :bluejump:

The bumper install was very straight forward. The bumper included 2 sets of brackets (one large set, one small set), and 12 bolts, washers, and 10 flange nuts.

First I removed the stock bumper using the instructions here:

Front bumper removal instructions - Toyota 120 Platforms Forum

Next I removed the center support to fit a winch.

Install the large frame to bumper bracket, but do not tighten it down. You will need to keep it a bit loose to make adjustments/fit.

Mount the CBI bumper, but do not tighten the bolts. You will need to keep them loose to make adjustments/fit.

I first centered the bumper and tightened down the nuts that held the bracket to the frame. Then, I adjusted the height to get the bumper around 1/2 inch from the fenders and headlights.

I then installed the two small support brackets (pic shows how the small brackets go on).

And thats it!! The overall time to remove the factory bumper and install the CBI bumper was around 4-5 hours. I did the removal myself, but had my brother help with the CBI bumper install.

This bumper rocks!!:cheers:

 

[Ultramontanist]

Great write-up and beautiful bumper! The guys at CBI are great. I have the old design on mine and I have to say I think I'm a bit jealous, from your pics the new design looks a bit cleaner than mine. Enjoy!

 

[mikey's2010SR5]

Good looking bumper

 

[blk-4runner]

thanks for the write-up, cant wait til i recieved my front bumper from cbi.

 

[loconzly]

Mmmm....nice bumper! I've been hunting for a good one and this one seems beefy and streamlined without being too giant.

Do you know what it weighs?

 

[Runner27]

Nice bumper. Just a side note: your 4runner 2wd?

 

[gaterose]

Looks great! I have a feeling I'm going to end up buying a bumper...

 

[Colemanfu]

Yea, kind of wish I could "un see it" ha.
That's a sharp looking setup. Well done!
What's next :biggrin2:?

 

[run4estrunner]

nice, i like the coverage on the sides, as in it leaves less open than a Demello without being as bulky as a SW.

 

[noobshooter]

Do you know what it weighs?

Not sure. CBI's site says 120 lbs. I can tell you that I was able to lift it off the ground myself, and I have a bad back. It was lighter than I expected.

 

[Doozi]

Very, very nice! I've been dying to see their new design!

Thanks for sharing!!

 

[noobshooter]

Nice bumper. Just a side note: your 4runner 2wd?

Yes, it's 2WD. I don't have a big need for a 4WD. Most of my off-road adventures are on gravel/trail roads at high speed. + Im getting ready for the zombie apocolypse like everyone else :ak472:

 

[Dawg4Runner]

I like it! Steve is an artist.

 

[wadle5]

Bumper

A couple of month ago I called CBI to order a front bumper. Nathan said that CBI was in the process of making some changes to the design of the bumper. He asked if I wanted to order the old design, or wait a couple of months and wait for the new design. I decided to wait and this is the bumper I received :bluejump:

The bumper install was very straight forward. The bumper included 2 sets of brackets (one large set, one small set), and 12 bolts, washers, and 10 flange nuts.

First I removed the stock bumper using the instructions here:

Front bumper removal instructions - Toyota 120 Platforms Forum

Next I removed the center support to fit a winch.

Install the large frame to bumper bracket, but do not tighten it down. You will need to keep it a bit loose to make adjustments/fit.

Mount the CBI bumper, but do not tighten the bolts. You will need to keep them loose to make adjustments/fit.

I first centered the bumper and tightened down the nuts that held the bracket to the frame. Then, I adjusted the height to get the bumper around 1/2 inch from the fenders and headlights.

I then installed the two small support brackets (pic shows how the small brackets go on).

And thats it!! The overall time to remove the factory bumper and install the CBI bumper was around 4-5 hours. I did the removal myself, but had my brother help with the CBI bumper install.

This bumper rocks!!:cheers:

What do you have for suspension to handle that?

 

[noobshooter]

What's next :biggrin2:?

Upgrade the skids.
Replace the P.O.S Tom Tom unit/speakers.
Dillon mini gun turret (for the zombies) SUV-mounted Dillon Aero Minigun - YouTube
CBI rear bumper package.

 

[noobshooter]

What do you have for suspension to handle that?

Overland/Radflo 2.5" coilovers.

 

[absolute yota]

Thats what I want , with a single hoop in the center. Looks nice, how long did it take to get it after ordering ?

 

[JustSomeName]

how much did they charge you for the bumper? their site doesnt show a price...

 

[noobshooter]

Thats what I want , with a single hoop in the center. Looks nice, how long did it take to get it after ordering ?

2+ months, but I ordered the bumper before they were finished with the design. I was told the bumper would take some time before I would get it, and was also kept informed of the progress. All the other products (skids, tire carrier) I have ordered from them have been delivered within a month.

how much did they charge you for the bumper? their site doesnt show a price...

Contact CBI. Their pricing was broken down with options.

 

[97BlackAckCL]

Love the bumper, looks great!